Mtx Audio WET75.4 Handleiding

Mtx Audio Hifi systeem WET75.4

Lees hieronder de 📖 handleiding in het Nederlandse voor Mtx Audio WET75.4 (32 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 85 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

OWNER’S MANUAL

WET SERIES AMPLIFIERS

M T X . C O M

Use your smartphone to scan or visit

youtube.com/user/MTXAudioUSA

to learn how to properly install this

ampliﬁer.

M T X . C O M

PRODUCT INFORMATION

Model #

Serial #

Dealer’s Name

Date of Purchase

INTRODUCTION

Thank you for purchasing this MTX Audio Hi-Performance marine grade ampliﬁer. Proper installation

matched with MTX speakers and subwoofers provide superior sound and performance for endless

hours of enjoyment on your boat wherever the current takes you. Congratulations and enjoy the

ultimate audio experience with MTX!

FEATURES

• Compact Size

• Double Sided PCB

• Surface Mount Components

• MOSFET Design

• LPF and HPF Crossover

• Adjustable Bass Boost

• Noise Free Design

• Short, Thermal, and High/Low Voltage Protection

• Conformal Coated PCB

• Plexiglass Cover for Controls

• Stainless Steel Hardware

• Rubber Gaskets Around RCA Connectors

CONTROL FUNCTIONS

1. Speakers - Connect speakers/subwoofers to these terminals. Be sure to check wire for proper

polarity. Never connect the speaker cables to the chassis ground.

2. +BATT (+12 Volt Power) - Connect this terminal through a FUSE or CIRCUIT BREAKER to the

positive terminal of the vehicle battery or the positive terminal of an isolated audio system

battery. WARNING: Always protect this power cable by installing a fuse or circuit breaker of the

appropriate gauge within 18 inches (45cm) of the battery terminal connection.

3. Remote Turn On - This terminal turns on the ampliﬁer when (+) 12 volt is applied to it. Connect it to

the remote turn on lead of the head unit or signal source.

4. GND - Run an equal gauge wire from the Ground (GND) terminal on the MTX ampliﬁer to the

negative terminal on the battery. Use the shortest distance possible. It is always a good idea to

replace the factory ground at this time with a cable equal or larger than the new ampliﬁer power

cable. CAUTION: Do not connect this terminal directly to the vehicle battery

ground terminal or any other factory ground points.

5. RCA Input Jacks - These RCA input jacks are for use with source units that have RCA outputs. A

source unit with a minimum level of 200mV is required for proper operation. The use of high

quality twisted pair cables is recommended to decrease the possibility of radiated noise entering

the system.

6. Gain Control - The Gain control will match the ampliﬁer’s sensitivity to the source units signal

voltage. The operating range is 5V to 200mV. This is NOT a volume control.NOTE:

M T X . C O M 3

7. Low Pass Filter Control (Mono Block) - This control is used to select the desired low pass x-over

frequency. The frequency can be adjusted from 40Hz to 220Hz for all bass mono models.

8. Subsonic Filter Control (Mono Block) - This control can ﬁlter out unwanted low frequency from

20Hz (OFF) to 50Hz. This function should only be used with vented enclosures.

9. Bass Boost Level Switch (Mono Block) - This switch can boost bass level by 0dB, 6dB, or 12dB.

The boost frequency is centered at 50Hz.

10. High Pass Filter (Full Range) - This controls the frequencies played for the front channels. Low

frequencies can be cut off from OFF to 200Hz. At OFF position, no low frequencies cut off,

meaning full range.

11. X-Over Mode and Frequency Control (Full Range) - These controls allow control over the

frequencies played for the rear channels. There is an option for Low Pass, Full Range, or High

Pass. In LP or HP mode, the crossover frequency can be tuned from 50Hz to 750Hz.

12. Power Indicator - This LED will light up when the ampliﬁer is working properly.

13. Protection Indicator - The Red LED will light up and ﬂash if there is a fault presented to the

ampliﬁer. Please disconnect the ampliﬁer and resolve the fault before reconnecting the ampliﬁer.

PANEL LAYOUT

4-Channel Ampliﬁer Panel Layout

1 4

6 13

6 12115

Product specificaties

Merk:	Mtx Audio
Categorie:	Hifi systeem
Model:	WET75.4
Kleur van het product:	Zwart
Breedte:	45.7 mm
Diepte:	96.5 mm
Hoogte:	35.5 mm
Signaal/ruis-verhouding:	80 dB
Efficientie:	1 procent
Maximaal uitgangsvermogen (RMS):	400 W
Input sensitiviteit:	200 mV
Versterker klasse:	A/B
Aantal versterker kanalen:	4 kanalen
RMS vermogen uitvoer per kanaal (4 Ohm):	75 W
RMS vermogen uitvoer per kanaal (2 Ohm):	100 W