Mtx Audio RT604 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Mtx Audio RT604 (44 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/44
RT604
4 Channel Class-AB Power Amplifier
360W
RMS
Designed by MTX in Phoenix, USA
www.mtx.eu.com
www.mtx.com
GNDREM+12V
POWER SPEAKER
FRONT
FRONT
REAR
REAR
BRIDGE
R+
+
R- L+ L-
-
LOW INPUTHLI
FR FL
+ R - G - L + GAIN X-OVER LPFHPF
6V 0,1V
6V 0,1V
40Hz 400Hz
FULL
HPF LPF
FULL
HPF LPF
40Hz 400Hz
40Hz 400Hz 40Hz 400Hz
FR FL
+ R - G - L +
www.mtx.com - www.mtx.eu.com
Owners Manual - RT604
Introduction
Thank you for purchasing an MTX Audio Hi-Performance amplier. Proper installation matched with MTX speak-
ers and subwoofers provide superior sound and performance for endless hours of waking the neighbors, slam-
min' your friends or at out stomping wanna-be players. Congrats and enjoy the ultimate audio experience with
MTX !
Specications :
• 4-Channel Class-AB Amplier
• CEA2006 certied Power Output :
- 90 watts RMS x 4-channel at 2 ohm and THD+N ≤1%
- 60 watts RMS x 4-channel at 4 ohm and THD+N ≤1%
- 180 watts RMS x 2-channel at 4 ohm and THD+N ≤1%
• Crossover :
- High pass 12dB/oct variable from 40Hz to 400Hz
- Low pass 12dB/oct variable from 40Hz to 400Hz
• Signal-to-Noise Ratio (1 watt) : > 80dB
THD+Noise (Distortion) (1 watt) : ≤ 1%
• Frequency Response (±1dB) : 20Hz-30000Hz
• Maximum Input Signal : 6V
• Maximum Sensitivity : 100mV
• Dimensions : 364mm x 180mm x 55mm
• High level inputs
Control Panel
Control Panel :
Gain Control (GAIN) : The gain control matches the input sensitivity of the amplier to the source unit being used.
The operating range varies from 100mv to 6V.
Adjusting the gain
1. Turn the gain control on the amplier all the way down (counter clockwise).
2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplier is now calibrated to the output of the source unit.
Low-Pass High-Pass X-Over Switch (X-OVER) :
In “LPF” position, the active low pass (LP) x-over is turned on
In “HPF” position, the active high pass (HP) x-over is turned on
In “FULL position, the x-over is turned o
High Pass X-Over Frequency Control (HPF) :
Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..
Low Pass X-Over Frequency Control (LPF) :
Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..
RCA Inputs (LOW INPUT) : These RCA inputs are used with source units that have RCA or Line level outputs.
(Source units need a minimum level of 100mV output for proper operation of the amplier).
MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-
ated noise entering the system.
PowerOn/Protection LED - The LED illuminates red when the amp is switched on. When the amps is in shortcir-
cuit or thermal protection, the LED is blinking.
Speaker level inputs (HLI) :
This input will allow the amplier to operate from source units with speaker-level outputs. Output speaker leads
from the source unit should be tied directly to the wire harness provided with the amplier.
Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.
(+12V) Power Terminal : This is the main power input for the amplier and must be connected directly to the posi-
tive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable in the
vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to massive
currents that can induce noise into the audio system. It is also very important to have a tight, secure connection
for maximum performance. MTX recommends using 10mm
2 power wire with the MTX RT604 amplier.
Remote Terminal (REM) : The amplier can be turned on by applying 12 volts to this terminal. Typically this volt-
age is supplied by a wire from the source unit marked remote” or “power antenna.
Ground Terminal (GND) : A proper ground is required for your amplier to operate at peak performance. A short
ground cable the same diameter as the power cable should be used to attach the ground terminal directly to
the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be
attached.
Speaker Terminals (SPEAKER) : Connect speakers to these terminals. Observe speaker polarity throughout the
system. Improper phase can result in loss of bass response and/or poor overall sound quality.
Bridge Mode : When bridging the amplier, use the right positive terminal and the left negative terminal only.
Warning : do not bridge the amplier with an impedance lower than 4 ohm.
Fuse (FUSE) : When fuse blow, replace them with the same value. Never use a higher rated fuse !
Caution : fuses are located under the amp.


Product specificaties

Merk: Mtx Audio
Categorie: Receiver
Model: RT604
Kleur van het product: Zilver
Breedte: 364 mm
Diepte: 55 mm
Hoogte: 180 mm
Signaal/ruis-verhouding: 80 dB
Maximaal uitgangsvermogen (RMS): 180 W
Input sensitiviteit: 100 mV
Versterker klasse: A/B
Aantal versterker kanalen: 4 kanalen
RMS vermogen uitvoer per kanaal (4 Ohm): 60 W
High pass filter: Ja
Low pass filter: Ja
RMS vermogen uitvoer per kanaal (2 Ohm): 90 W
High-pass filterbereik: 40 - 400 Hz
Low-pass filterbereik: 40 - 400 Hz

Heb je hulp nodig?

Als je hulp nodig hebt met Mtx Audio RT604 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Mtx Audio

Handleiding Receiver

Nieuwste handleidingen voor Receiver