Mtx Audio RT202 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Mtx Audio RT202 (19 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/19
AMPLIFIER
OWNER’S
MANUAL
RT202 RT404
AMPLIFIER OWNER’S MANUAL
2
3
CONGRATULATIONS...
on your purchase of a new MTX Audio
Road Thunder Amplifier! MTX has long
been the industry leader in mobile audio,
and we have reached new heights with
the development of the new MTX Road
Thunder amplifiers. You couldn’t have
chosen a more reliable, powerful, or
better performing amplifier.
We manufacture every amplifier using
the latest Intelligent Surface Mount
Technology. Some of the advantages of
the new design are significant improve-
ments to the amplifiers electrical and
mechanical properties. ISMT devices feature
substantially shorter internal and external
lead lengths. This reduces stray capacitance
and inductance, which results in cleaner and
more accurate musical reproduction with sig-
nificantly less noise interference. The ISMT
mounter produces amplifier boards with
smaller and lighter components, which are
more resistant to vibrations inherent in the
automotive environment.
We want to ensure you get continuous high
performance from your MTX Road Thunder
amplifier, so we recommend that you have it
professionally installed by your authorized
MTX dealer.
HOW TO USE THIS MANUAL
If you are installing this amplifier yourself, we
recommend that you read the manual cover-
to-cover before you install it. Familiarize
yourself with the features and details on the
input and output panels. Make sure you have
all the equipment you need. Then follow the
step-by-step installation instructions included.
Sample installation diagrams may be found
on our website:
mtx.com
If you have any questions, write or call us:
MTX Audio
4545 E. Baseline Rd. Phoenix, AZ 85042
602-438-4545 • 800-CALL MTX
technical@mtx.com
mtx.com
Please take a moment to register your
purchase online at mtx.com.
Please, also record the serial number of
your amplifier in the space provided below,
and keep this manual for future reference,
as well as your sales receipt as proof of
ownership. (The serial number of your
amplifier is marked on the bottom of its
metal chassis.)
Serial Number:
Date of Purchase:
Introduction
ENGLISH
Unique rubber Insulated Iso-Feet™
Nickel-plated, heavy duty terminal block type connectors
Speaker and low level inputs
Input select 2CH/4CH switch on RT404 functions as a built-in Y connector
Color-coded wire harness for speaker level input installation
Smart-Engage™ auto-turn on for easy integration with factory head units
Built-in, defeatable18dB/octave HP/LP crossover at 85 Hz
RT404 front channel crossover is a defeatable18dB/octave, high pass, at 85Hz
Adjustable input sensitivity
Bridgeable, multi-channel circuit design
Regulated PWM Mosfet Switching Power Supply
New, more reliable high powered transformers
Buffered, isolated output for daisy chaining multiple amplifiers
Pure N-Channel Design
Intelligent Surface Mount Technology
Class A 100% discrete driver circuit topology
Real-time computerized protection circuit
Anti-shock PCB mounting design
Acoustically Seamless Turn-on/Turn-off
Features
Specifications
RT202
RMS Power measured at 14.4 Volts DC:
37.5 Watts x 2 into a 4 Ohm load with < 1% THD
75 Watts x 2 into a 2 Ohm load with < 1% THD
150 Watts bridged into a 4 Ohm load with < 1% THD
Dynamic Power measured at 14.4 Volts DC:
50 Watts x 2 into a 4 Ohm load
100 Watts x 2 into a 2 Ohm load
200 Watts bridged into a 4 Ohm load
Signal to Noise Ratio: 100dB A-Weighted
(Referenced to Rated PWR at 1VRMS Input Sensitivity)
Frequency Response: 20-20,000 Hz ±.25dB
Crossover: Defeatable, 18dB/octave at 85 Hz,
selectable for high pass, low pass
Dimensions: Including Iso-Feet™
7.98" x 9.75" x 2.1" (20.3cm x 24.8cm x 5.3cm)
RT404
RMS Power measured at 14.4 Volts DC:
37.5 Watts x 4 into a 4 Ohm load with < 1% THD
75 Watts x 4 into a 2 Ohm load with < 1% THD
150 Watts x 2 bridged into a 4 Ohm load with < 1% THD
Dynamic Power measured at 14.4 Volts DC:
50 Watts x 4 into a 4 Ohm load
100 Watts x 4 into a 2 Ohm load
200 Watts x 2 bridged into a 4 Ohm load
Signal to Noise Ratio: 100dB A-Weighted
(Referenced to Rated PWR at 1VRMS Input Sensitivity)
Frequency Response: 20-20,000 Hz ±.25dB
Crossover: Defeatable, 18dB/octave at 85 Hz,
selectable for high pass, low pass, or full range on
rear channels and high pass or full range for front
channels
Dimensions: Including Iso-Feet™
11.5" x 9.75" x 2.1" (29.2cm x 24.8cm x 5.3cm)
5
FRONT
GAIN
AMP
X–OVER
2CH 4CH
FR HP
R L
FRONT IN SUM OUT REAR IN
AMP
X–OVER
REAR
GAIN
LP FR HP
R+ L+
R L
R+ L+
L
R
L
R
SPEAKER
LEVEL
INPUT
FRONT
RCA
INPUT
SPEAKER
LEVEL
INPUT
REAR
AMPLIFIER OWNER’S MANUAL
4
1. RCA Input Jacks These RCA input jacks are for use with source units that have RCA or Line Level
Outputs. An independent set of jacks are provided on the RT404 for front and rear stereo inputs. A source
unit with a minimum level of 200mV is required for proper operation. The use of high quality twisted pair
cables is recommended to decrease the possibility of radiated noise entering the system.
2. Input Select 2CH/4CH This switch, found on the RT404, is used to match the amplifier’s input to the
source units output so all four channels of the amplifier are driven. If your source unit has 2 outputs (left
and right) connect them to the amplifier’s front channel inputs, and place the input select switch in the 2CH
position. If your source unit has 4 outputs, (left front, left rear, right front, right rear) connect them to the
amplifier inputs and place the input select switch in the 4CH position. In the 4CH position, the fader on
your source unit will operate.
3. Speaker Level Inputs This input will allow the amplifier to operate from source units with speaker level
outputs. Output speaker leads from the source unit should be tied directly to the wire harness provided
with the amplifier.
Wire harness color codes:
Grey/Black = Source unit right negative (-) White/Black = Source unit left negative (-)
Solid Grey = Source unit right positive (+) Solid White = Source unit left positive (+)
With the Smart-Engage™ auto-turn-on circuit, a remote turn-on wire is not necessary when connecting
the speaker-level input wire harness to a high powered source unit. The amplifier will automatically turn
on when music is received.
4. RCA Output These RCA outputs allow for a signal to be sent to other amplifiers in a daisy-chain
configuration. The RCA outputs on all Road Thunder series amplifiers will send a full-range signal to
additional amplifiers.
5. Gain Controls – These controls are used to match the input sensitivity of the amplifier to the particular
source unit that you are using. The controls are factory set to 1Vrms. Note that the RT404 has a separate
gain control for front and rear channels.
6. Crossover Select This switch controls the type of crossover configuration that you desire. Road
Thunder series 2-channel amplifiers include a defeatable 18dB/octave, 85Hz crossover that is high
pass/low pass or full range selectable. The RT404 four channel amplifier includes a defeatable
18dB/octave, 85Hz crossover that is high pass or full range for the front channels, and a high pass, low
pass or full range for the rear channels.
Input Panel Layout


Product specificaties

Merk: Mtx Audio
Categorie: Receiver
Model: RT202

Heb je hulp nodig?

Als je hulp nodig hebt met Mtx Audio RT202 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Mtx Audio

Handleiding Receiver

Nieuwste handleidingen voor Receiver