Mtx Audio RFL5300 Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor Mtx Audio RFL5300 (40 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/40
mtxaudio.eu
RFL5300
5 Channel Class-AB Power Ampliļ¬er
850W RMS CEA
Ownerā€™s Manual - MTX RFL5300
Thank You !
Thank you for purchasing an MTX Audio High-End ampliļ¬er. Proper installation matched with MTX speakers and subwoofers provide
superior sound and performance for endless hours of waking the neighbors, slamminā€™ your friends or ļ¬‚at out stomping wanna-be
players. Congrats and enjoy the ultimate audio experience with MTX !
Speciļ¬cations :
ā€¢ 5-Channel Class-AB ampliļ¬er
ā€¢ CEA2006 certiļ¬ed Power Output :
Channels 1, 2, 3, 4
- 120 Watts RMS x 4-channels at 2 ohm and THD+N ā‰¤1%
- 80 Watts RMS x 4-channels at 4 ohm and THD+N ā‰¤1%
- 240 Watts RMS bridged x 2 at 4 ohm and THD+N ā‰¤1%
Channel 5
- 370 Watts RMS x 1-channel at 2 ohm and THD+N ā‰¤1%
- 250 Watts RMS x 1-channel at 4 ohm and THD+N ā‰¤1%
ā€¢ Crossover :
Channels 1, 2
- High pass 12dB/oct variable from 40Hz to 5000Hz
Channels 3, 4
- Low pass 12dB/oct variable from 800Hz to 5000Hz
- High pass 12dB/oct variable from 40Hz to 800Hz
- Band pass 12dB/oct variable from 40Hz to 5000Hz
Channel 5
- Low pass 24dB/oct variable from 40Hz to 800Hz
ā€¢ Signal-to-Noise Ratio (1 Watt) : > 98dB
ā€¢ THD+Noise (Distortion) (1 Watt) : ā‰¤ 0,05%
ā€¢ Frequency Response (Ā±1dB) : 10Hz-90000Hz
ā€¢ Maximum Input Signal : 6V
ā€¢ Maximum Sensitivity : 200mV
ā€¢ Phase switch 0Ā° or 180Ā°
ā€¢ EBC remote control
ā€¢ Dimensions : 626mm x 204mm x 59mm
RCA Inputs - These RCA inputs are used with head units that have RCA or Line level outputs (head units need a minimum level of
200mV output for proper operation of the ampliļ¬er).
MTX recommends only high quality RCA cables to decrease the possibility of radiated noise entering the system.
Gain Control - The gain control matches the input sensitivity of the ampliļ¬er to the head unit being used. The operating range varies
from 200mv to 6V.
Adjusting the gain
1. Turn the gain control on the ampliļ¬er all the way down (counter clockwise).
2. Turn up the volume control on the head unit to approximately 3ā„4 of maximum.
3. Adjust the gain control on the ampliļ¬er until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The ampliļ¬er is now calibrated to the output of the head unit.
High Pass X-Over Switch - Used to turn on the active high-pass (HP) x-over on and oļ¬€. When engaged (On) the x-over is ā€œONā€, when
disengaged (Oļ¬€) the x-over is ā€œOFFā€.
High Pass X-Over Frequency Control - Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from
40Hz to 5000Hz (Ch1, Ch2). The frequency is adjustable from 40Hz to 800Hz (Ch3, Ch4).
Low Pass X-Over Switch - Turns the active low pass (LP) x-over on and oļ¬€. When engaged (On) the x-over is ā€œONā€, when disengaged
(Oļ¬€) the x-over is ā€œOFFā€
Low Pass X-Over Frequency Control - Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 800Hz
to 5000Hz (Ch3, Ch4). The frequency is adjustable from 40Hz to 800Hz (Ch5).
Band Pass X-Over : To use, turn ā€œONā€ the LP (3) and HP (5) x-overs at the same time, creating a band-pass x-over for kick woofers or
midranges. You can tune the ļ¬lter with frequency controls (4) and (6).
Input Switch : If the head unit is equipped with 4 RCA outputs (2 front and 2 rear), use the ch-3 ch-4 mode and connect the 4 RCA
outputs to the ch-1 ch-2 ch-3 ch-4 RCA inputs on the amp. If only 2 RCA outputs are available from the head unit, use the ch-1 ch-2
mode and connect the RCA outputs to the ch-1 and ch-2 inputs of the amp.
Input Switch channel 5 : If the head unit is equipped with a dedicated subwoofer output, use the ch-5 mode connect the RCA from the
subwoofer output to the subwoofer ch-5 RCA inputs on the amp. If no dedicated subwoofer output is available from the headunit use
the ch1 - ch2 mode, the channel 5 will take the signal from ch-1 and ch-2 RCA inputs on the amp.
Phase switch - Used to match the bass from subwoofers and front speakers. Toggle the phase switch from 0Ā° to 180Ā°. Keep the loudest
bass response.
EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while the EBC itself can be
placed anywhere in the vehicle for on demand bass adjustments. EBC is included.
Controls and Inputs :


Product specificaties

Merk: Mtx Audio
Categorie: Autoradio
Model: RFL5300

Heb je hulp nodig?

Als je hulp nodig hebt met Mtx Audio RFL5300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Mtx Audio

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio