Mount-It! MI-397 Handleiding

Mount-It! Flat panel steun MI-397

Lees hieronder de 📖 handleiding in het Nederlandse voor Mount-It! MI-397 (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

please contact us

(Mount-It!) for assistance.

(Mount-It!) for a replacement.

please contact us

SKU: MI-397

TV Wall Mount with Extra Long Extension

The angle of the screen can be adjusted down up to 10 degrees and up 5 degrees. To adjust the tilt angle

of the TV, loosen the tilt adjustment nuts shown here then adjust the tilt to the desired angle then tighten the

nuts back down.

Note: If the screen tilts down slowly over time adjust the screen back to the proper angle and ensure the tilt

adjustment nuts are firmly tightened.

The mount allows up to 3 degrees of levelling adjustment post installation. To adjust the level of the TV

loosen the 2 nuts located behind the rectangular VESA plate, level the TV then tighten the 2 nuts again to

secure the TV in position.

Tilt Adjustment

4Levelling Adjustment

We recommend using professional installation services if you are unable to follow the instructions provided in this manual.

(855)- 925-5668

Please scan this QR code

to visit the product page.

+5°

-10°

S-5

-3° +3°

S-5

ø 6mm

(ø 1/4")

90mm

(3.5")

Wood Stud Installation Option

Attach the TV to the VESA Arms (No Spacers)

Attach the TV to the VESA Arms (With Spacers)

MI-397 80

WARNING: This installation manual is intended to provide guidance on how to install the TV mount and the TV on a suitable wall.

Please contact a qualified professional if you are unsure of the steps described in the manual or have doubts about the safety of the

installation. Improper installation may cause damage or serious injury. We cannot be held liable for damage or injury caused by

improper mounting. Incorrect assembly, inappropriate use or for use cases not explicitly specified in this document. If unsure, please

Mount and Accessories

TV Mounting Hardware

Wall Mounting Hardware

CHOKING HAZARD. Package includes small parts. Not for children under 3 years. Adult supervision is required

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used.

Use the correct monitor mounting hardware suitable for your installation.

1. Use a stud finder to locate the wall studs and mark their location with a pencil.

2. Hold, tape or secure the Wall Template (#L) to the wall at the desired installation location. Use a bubble

level to ensure the straightness of the Wall Template (#L) and on the center of the studs mark the locations

for the 4 Lag Screws as shown. Once marked, remove the Wall Template.

3. Use a 1/4” drill bit and drill on the marked locations to a depth of 3.5”.

4. Hold the Mount (#M) to the wall over the holes and secure to the wall using all 4 Lag Screws (#A) and

Lag Washers (#B).

Select the appropriate size Mounting Bolt (Select one size #D, #E) and Square Washer (#C) for your

display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the

correct bolt size for your display refer to your TV user manual or contact the TV manufacturer for sizing

information. Attach the 2 VESA Arms (#N) to the back of your TV using the selected bolts and washer.

If necessary, use the included spacers (#I, J) between the mount and the screen as shown above to adjust

the length of the mounting bolt. Multiple spacers can be used in combination to achieve the desired bolt

depth.

Select the appropriate size Mounting Bolt (Select one size #F, #G,#H) and Square Washer (#C) for your

display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the

correct bolt size for your display refer to your TV user manual or contact the TV manufacturer for sizing

information. Attach the 2 VESA Arms (#N) to the back of your TV using the selected bolts, washer and

spacers.

Hang the TV on the mount arms as shown in the diagram. Caution: Use the help of a second person for

safe lifting and easier installation.

Attach the Safety Clips (#S-1 and #S-2) to the bottom of the VESA arms as shown here, and secure them

in place using Safety Bolts (#S-3).

1.Hold, tape or secure the Wall Template (#L) to the wall at the desired installation location. Use a bubble

level to ensure the straightness of the Wall Template and mark the locations for the 5 Lag Screws as

shown, then remove the template.

2.Use a 2/5” drill bit and drill on the marked locations to a depth of 3.7”. Note: Do not drill mounting holes

into mortar (such as between bricks or stones) only drill and install into solid stone or concrete surfaces.

3.Clear any dust and debris from the holes and insert the 5 Concrete Anchors (#K). Hold the Mount (#M) to

the wall over the holes and secure to the wall using all 5 Lag Screws (#A) and Lag Washers (#B).

Hang the TV on the Mount Arms

55kg

(121lbs)

Wall Mount

M (x1)

VESA Arms

N (x2)

Wall Template

L (x1)

Hex Wrench

S-4 (x1)

S-1 (x1)

Security Clips

S-2 (x1)

Security Bolt

S -3 (x2)

Wrench

S-5 (x1)

Square Washer

C (x4)

15mm Spacer

I (x4)

5mm Spacer

J (x4)

Concrete Anchor

K (5)

M4 14x (x4)

M6 14x (x4)

M6 30x (x4)

M8x20 (x4 )

M8 45x (x4)

Lag Screw

A(x5)

Lag Washer

B (x5)

132

X X

√

16/24 inches

Level the wall plate

6mm(1/4”)

B A

90mm (3.5”)

Concrete/Stone Installation Option

1b 95mm

(3.7")

ø 10 mm

(ø 2 /5")

X X

√

D/E

F/H

S-1/S-2

S-3

Product specificaties

Merk:	Mount-It!
Categorie:	Flat panel steun
Model:	MI-397

Heb je hulp nodig?

Als je hulp nodig hebt met Mount-It! MI-397 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Flat panel steun Mount-It!

Mount-It! MI-395 Handleiding

19 November 2024

Mount-It! MI-14002 Handleiding

19 November 2024

Mount-It! MI-4753 Handleiding

19 November 2024

Mount-It! MI-14003 Handleiding

19 November 2024

Mount-It! MI-14009 Handleiding

23 Juni 2024

Mount-It! MI-394 Handleiding

23 Juni 2024

Mount-It! MI-14010 Handleiding

23 Juni 2024

Mount-It! MI-2752 Handleiding

23 Juni 2024

Mount-It! MI-20810 Handleiding

23 Juni 2024

Mount-It! MI-2753 Handleiding

23 Juni 2024

Handleiding Flat panel steun

Nieuwste handleidingen voor Flat panel steun

Twelve South HiRise Pro Handleiding

30 Januari 2025

XTRARM XTR-FS5030 Handleiding

30 Januari 2025

Rocstor ErgoReach ED7 Handleiding

30 Januari 2025

Atdec AWMS-DW Handleiding

30 Januari 2025

Atdec AWM-W Handleiding

30 Januari 2025

Atdec AWMS-HXB-H Handleiding

30 Januari 2025

Akai 1342TS1 Handleiding

30 Januari 2025

Chief TS318SU Handleiding

30 Januari 2025

Chief TS318TU Handleiding

30 Januari 2025

Adicam MINI Film Cart Handleiding

29 Januari 2025