Motorola MS350R Handleiding

Motorola Walkie talkie MS350R

Lees hieronder de 📖 handleiding in het Nederlandse voor Motorola MS350R (5 pagina's) in de categorie Walkie talkie. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

1MS350 Series

MS350 Series

KEM-ML36100-15

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using The Radio.

The information provided in this document supersedes the general

safety information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

This two-way radio contains a transmitter and a receiver. To

control your exposure and ensure compliance with the general

population/uncontrolled environment exposure limits, always

adhere to the following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the

radio generates measurable RF energy exposure only when

transmitting (in terms of measuring standards compliance).

Exposure to Radio Frequency Energy

This Motorola two-way radio complies with the following RF

energy exposure standards and guidelines:

• United States Federal Communications Commission, Code of

Federal Regulations; 47CFR part 2 sub-part J.

• American National Standards Institute (ANSI)/Institute of

Electrical and Electronic Engineers (IEEE) C95. 1-1992.

• Institute of Electrical and Electronics Engineers (IEEE) C95.

1-1999 Edition.

• International Commission on Non-Ionizing Radiation

Protection (ICNIRP) 1998.

• Ministry of Health (Canada) Safety Code 6. Limits of Human

Exposure to Radiofrequency Electromagnetic Fields in the

Frequency Range from 3 KHz to 300 GHz, 1999.

• Australian Communications Authority Radiocommunications

(Electromagnetic Radiation—Human Exposure) Standard, 2003.

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.

• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.

To ensure optimal radio performance and make sure human

exposure to radio frequency electromagnetic energy is within

the guidelines set forth in the above standards, always adhere

to the following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could

damage the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding

the antenna affects its effective range.

Body-Worn Operation

To maintain compliances with FCC guidelines if you wear a radio

on your body when transmitting always place the radio in a

Motorola-supplied or approved clip holder, holster, case or body

harness for this product. Use of non-Motorola-approved

accessories may exceed FCC guidelines.

If you do not use one of the Motorola-supplied or approved

body-worn accessories and are not using the radio held in the

normal use position, ensure the radio and its antenna are at

least 1 inch (2.5 cm) from your body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or

without an accessory cable, position the radio and its antenna

at least one inch (2.5 cm) from the body.

Approved Accessories

53724: Remote Speaker with Push-to-Talk Microphone

53725: Headset with Swivel Boom Microphone

53727: Ear bud with Push-to-Talk Microphone

53728: Flexible Ear Receiver

56320: Earpiece with Boom Microphone

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately shielded,

designed or otherwise configured for electromagnetic

compatibility. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received,

including interference that may cause undesired operation.

Facilities

To avoid electromagnetic interference and/or compatibility

conflicts, turn off the radio in any facility where posted notices

instruct you to do so. Hospitals or health care facilities may be

using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off the radio when onboard an

aircraft. Any use of a radio must be in accordance with

applicable regulations per airline crew instructions.

Medical Devices – Pacemakers

The Advanced Medical Technology Association recommends

that a minimum separation of 6 inches (15 cm) be maintained

between a handheld wireless radio and a pacemaker. These

recommendations are consistent with the independent research

by and recommendations of the U.S. Food and Drug

Administration.

People with pacemakers should:

• ALWAYS keep the radio more than 6 inches (15 cm) from

their pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the

potential for interference.

• Turn the radio OFF immediately if there is any reason to

suspect that interference is taking place.

Medical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing

aids. In the event of such interference, you may want to consult

your hearing aid manufacturer to discuss alternatives.

Medical Devices – Other

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately

shielded from RF energy. Your physician may be able to assist

you in obtaining this information.

For More Information

For further information, you may call Motorola at 1-800-638-5119,

e-mail us at giantintl@callcenter.com or visit us on the Internet

at www.motorola.com.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in

the area where you drive, and always obey them. If you do use

the radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a call

if driving conditions so require.

The use of a two-way radio while engaged in activities requiring

concentration may cause distraction or otherwise impair your

ability to safely participate in such activities. Always use

technology safely.

Do not place a portable radio in the area over an air bag or in the

air bag deployment area. Air bags inflate with great force. If a

portable radio is placed in the air bag deployment area and the

air bag inflates, the radio may be propelled with great force and

cause serious injury to occupants of the vehicle.

Potentially Explosive Atmospheres

Turn off the radio prior to entering any area with a potentially

explosive atmosphere. Only radio types that are especially

qualified should be used in such areas as “Intrinsically Safe.”

Do not remove, install or charge batteries in such areas. Sparks

in a potentially explosive atmosphere can cause an explosion or

fire resulting in bodily injury or even death.

Note: The areas with potentially explosive atmospheres referred

to above include fueling areas such as below decks on boats,

fuel or chemical transfer or storage facilities, areas where the air

contains chemicals or particles (such as grain, dust or metal

powders) and any other area where you would normally be

advised to turn off your vehicle engine. Areas with potentially

explosive atmospheres are often—but not always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off

the radio when you are near electrical blasting caps, in a

blasting area, or in areas posted “Turn off two-way radios.”

Obey all signs and instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a

damaged antenna comes into contact with your skin, a minor

burn can result.

Batteries

All batteries can cause property damage and/or bodily injury such

as burns if a conductive material—like jewelry, keys or beaded

chains— touch exposed terminals. The conductive material may

complete an electrical circuit (short circuit) and become quite hot.

Exercise care in handling any charged battery, particularly when

placing it inside a pocket, purse or other container with metal

objects.

Exercise care when removing NiMH or AA batteries. Do not use

sharp or conductive tools to remove either of these batteries.

Battery Charger Safety Instructions:

Save these Instructions

1. Do not expose the charger to rain or snow.

2. Do not operate or disassemble the charger if it has received

a sharp blow, or has been dropped or damaged in any way.

3. Never alter the AC cord or plug provided with the unit. If the

plug will not fit the outlet, have the proper outlet installed by

a qualified electrician. An improper condition can result in a

risk of electric shock.

4. To reduce the risk of damage to the cord or plug, pull the

plug rather than the cord when disconnecting the charger

from the AC receptacle.

5. To reduce the risk of electric shock, unplug the charger from

the outlet before attempting any maintenance or cleaning.

6. Use of an attachment not recommended or sold by Motorola

may result in a risk of fire, electric shock or personal injury.

7. Make sure the cord is located so it will not be stepped on,

tripped over or subjected to damage or stress.

8. An extension cord should not be used unless absolutely

necessary. Use of an improper extension cord could result in

a risk of a fire and/or electric shock. If an extension cord

must be used, make sure that:

• The pins on the plug of the extension cord are the same

number, size and shape as those on the plug of the

charger.

Two-Way Radio

User’s Guide

The MS350R is approved for use in the US only.

This radio floats with included NiMH battery.

It may not float with some AA batteries.

• The extension cord is properly wired and in good

condition.

• The extension cord size is 18 AWG for lengths up to 100

feet, and 16 AWG for lengths up to 150 feet.

9. The supply cord of the AC adaptor cannot be replaced. If the

cord is damaged, call customer service at 1-800-638-5119 or

e-mail us at giantintl@callcenter.com.

2MS350 Series

For a fax:

Contact the

Fax-0n-Demand

system

For mail service:

Call the FCC

Forms Hotline

If you have

questions about

the FCC License:

Call the FCC

1-202-418-0177 1-800-418-FORM

(3676)

1-888-CALL-FCC

(225-5322)

Display Screen Guide

Control Buttons

Getting Started

Waterproof

This radio is waterproof to IP-67 standards. It will withstand

submersion under up to 1 meter of water for up to 30 minutes.

The radio is resistant to water, rain, and splashes only when the

battery cover and headset accessory port are sealed. Open the

battery compartment door or headset port cover only when the

radio is dry. Use of a headset accessory should be in dry

environments only.

The charging base and AC adaptor are not waterproof. Do not

expose the charger to rain or snow. Charge the radios only in a

dry location. Do not place wet radios into the charging base.

Installing the Batteries

Radio floats with included NiMH battery. It may not float with

some AA batteries. Each radio can use either 1 NiMH

rechargeable battery pack or 3 AA alkaline batteries and beeps

when the batteries are low.

Installing NiMH Rechargeable Battery Pack (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Remove the NiMH battery pack from the clear plastic bag

(do not disassemble or unwrap the battery pack).

4. Insert the NiMH battery pack with the diagram facing you.

(The ribbon should be underneath the battery pack and

should wrap around the right side of the pack for easy

removal.)

5. Close the battery cover and tighten the retaining screw on

the battery door.

Installing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door and open the cover.

3. Insert the three AA alkaline batteries with + and - polarity as

shown inside. (The ribbon should be underneath the AA

alkaline batteries and should wrap around the right side of

the batteries.)

4. Close the battery cover and tighten the retaining screw on

the battery door.

Caution: Radio may not float with some AA batteries installed.

Radio Battery Meter

The radio battery icon shows the battery charge level, from

full to empty . When the radio has one segment left,

the radio chirps periodically or after releasing (Low Battery

Alert).

Removing the NiMH Battery Pack (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door to release the battery cover and

open the cover.

3. Remove the NiMH battery pack by pulling the ribbon

attached to the radio.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Removing the Three AA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, loosen the retaining

screw on the battery door, release the battery cover and

open the cover.

3. Gently remove each alkaline battery by easing each battery out

individually.

4. Close the battery cover and tighten the retaining screw on

the battery door.

Notes

• Exercise care when removing NiMH or AA batteries. Do not

use sharp or conductive tools to remove either of these

batteries.

• Remove the batteries before storing the radio for extended

periods of time. Batteries corrode over time and may cause

permanent damage to the radio.

• The battery door must be tightly closed with the screw to

maintain the waterproof seal of the radio.

Using the Battery Charger (Optional Accessory)

The battery charger provides drop-in charging convenience for

NiMH batteries and can be placed on any flat surface, such as a

desk or workbench. Charge the NiMH battery overnight (at least

16 hours) before using it for the first time. After the initial charge,

an empty battery is fully charged within 14 hours.

1. Follow the steps above to install a NiMH Battery Pack.

2. Plug the AC power supply cord into the jack on the desk

stand.

3. Plug the AC power supply into a standard wall outlet.

4. With a radio facing forward, slide it into one of the charging

pockets.

5. When charging in the battery charger, the red light on the

charger base will glow continuously.

Notes

• The light will remain red after the NiMH battery pack is fully

charged.

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery temperature

acclimates (usually about 20 minutes).

• For optimal battery life, remove the radio from the charger

within 16 hours. Do not store the radio while connected to

the charger.

• If the radio is kept on while charging, the charging time will be

extended.

• Even though the charger is connected, you may not be able to

transmit a message if the battery is completely empty .

Allow time for the battery to charge to 1 bar before

attempting to transmit a message.

• When the radio is wet from rain or snow, thoroughly dry the

surface before charging or removing the batteries.

Attaching and Removing the Belt Clip

1. Attach belt clip to pocket or belt strap.

2. Align the belt clip post with the hole in the back of the radio.

3. Gently push until the clip clicks in place.

To Remove

1. Push down on the release tab at the top of the belt clip to

release the catch.

2. Pull the belt clip away from the back of the radio.

Turning the Radio On and Off

In the ON position, the radio chirps and briefly shows all feature

icons available on the radio. The display screen then shows the

current channel, code and all features that are enabled.

Press and hold for 3 seconds to turn the radio on. Press and

hold for 3 seconds to turn the radio off.

Setting the Volume

Press and hold for 3 seconds, then press the or keys

until you reach a comfortable listening level.

The MS350 has 16 volume levels controlled by the keys.

1. Press to increase volume.

2. Press to decrease volume.

3. Hold or to rapidly increase volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Talking and Listening

To communicate, all radios in your group must be set to the

same channel and Interference Eliminator Code.

1. To talk, press and hold .

2. When you are finished talking, release .

FCC Licensing Information

This Motorola radio operate s on General Mobile Radio Service

(GMRS) frequencies and is subject to the Rules and Regulations

of the Federal Communications Commission (FCC). The FCC

requires that all operators using GMRS frequencies obtain a

radio license before operating their equipment. To obtain the

FCC forms, please visit the FCC’s Web site at

wireless.fcc.gov/uls/index.htm?job=home to source form 605

and 159, which includes all the instructions you will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

Changes or modifications not expressly approved by Motorola

may void the user’s authority granted by the FCC to operate this

radio and should not be made. To comply with FCC requirements,

transmitter adjustments should be made only by or under the

supervision of a person certified as technically qualified to

perform transmitter maintenance and repairs in the private land

mobile and fixed services as certified by an organization

representative of the user of those services. Replacement of any

transmitter component (crystal, semiconductor, etc.) not

authorized by the FCC equipment authorization for this radio

could violate FCC rules.

Note:

Note: Note: Use of this radio outside the country where it was

intended to be distributed is subject to government regulations

and may be prohibited.

For maximum clarity, hold the radio two to three inches away

from your mouth and speak directly into the microphone. Do not

cover the microphone while talking.

Talk Range

This radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet

apart.

Power Boost

To boost the radio’s power up to high power, press the top portion

of the button when talking. If you know your party is close by,

you can conserve the battery’s energy by pushing the lower part

of the button to use less power.

Note:

Note:Note: If you are on an FRS only channel (see “Channels and

Frequencies” tables on overleaf for details) the radio will only use

low power when either portion of the is pressed.

Monitor Button

Use the Monitor function to check if a channel is currently in use

by others. For maximum range performance, the Monitor

function will also help you to hear signals that are weak.

To latch the Monitor function on, Press and hold for three

seconds. When an empty channel is located, you will hear

continuous static and noise on that channel.

To turn the Monitor function off, tap a second time or press .

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the

radio emits a continuous warning tone and stops transmitting if

you press for 60 continuous seconds.

Menu Options

There are 12 options you may set to your preferences. Each press

of the MENU key advances you to the next option setting. Press

the or keys to change the setting. The menu will

automatically close 5 seconds after the last press of any button.

After the last menu item, the radio exits MENU mode and returns

to operation of the radio. A press of the button while setting

any menu option will immediately save all your settings and return

to operation of the radio.

All MENU settings will revert back to the factory default values if the

battery is fully discharged or removed for more than 30 seconds.

Menus and Values

1. Channel (1-22 and 15R-22R)

2. Interference Eliminator Code (1-121 or OFF)

3. Call Tone (1-10 or OFF)

4. iVOX (ON/OFF)

5. VOX sensitivity (1-3)

6. QT Noise Filtering (ON/OFF)

7. VibraCall (ON/OFF)

8. Keypad Tones (ON/OFF)

9. Talk Confirmation Tone (ON/OFF)

10. Auto Power Off (30/60/90 minutes or OFF)

11. Repeater Channel Enable (ON/OFF)

12. Repeater Transmitted Interference Eliminator Code

Selecting the Channel

This radio has 22 simplex channels plus 8 repeater duplex

channels. Channels are shared by other radio users and channel

selection will vary based on your location. Select a channel that is

not being used from the 22 available simplex channels. Channels

8-14 are low power (FRS 0.5 watt). All other channels are GMRS.

When the radio is on a FRS 0.5 watt channel, displays. When

the radio is on a GMRS 1.5 watt channel, displays.

The 8 GMRS repeater duplex channels 15R – 22R are disabled

by default. See on overleaf in”Enabling Repeater Channels”

order to select a repeater channel.

See the tables on overleaf for“Channels and Frequencies”

details on channel frequencies.

1. Press . The current channel setting flashes.

2. Press or and select the channel.

3. Press to save the channel setting or to continue set up.

Selecting the Interference Eliminator Code

This radio has 121 Interference Eliminator Code settings. When a

channel is in use by 2 or more groups, this feature blocks the

reception of signals that do not carry the matching tone or code.

There are 121 privacy codes. 0 is the off position, no codes are

enabled, and all users of that channel will be heard.

Note: When you connect a headset, the radio is automatically

set to the last chosen sensitivity level.

QTNoise Filtering

The QTnoise-filtering feature helps to ensure uninterrupted

communication with other Motorola radios that have this

feature. This feature also filters out unwanted transmissions

from other radios. This is useful in places where there is

heavy radio traffic, such as amusement parks or ski resorts.

Note: QTnoise filtering is not available when the radio is

scanning.

To turn QTn oise filtering on or off:

1. Press until displays. The current setting On/Off

will flash.

2. Press or to turn noise filtering On or Off.

3. Press to confirm your selection or to continue

set up.

To transmit to a radio that has QTnoise filtering turned on:

1. Select the same channel and Interference Eliminator

Code as the other radio.

2. Press to send a call tone. This allows your voice to

pass through the QTnoise filter on the receiving radio.

3. Press and speak normally.

Note: If you skip step 2, the beginning of your message may

not be heard on the receiving radio. For a 30-second period,

starting after the last transmission, all transmissions

received on the selected channel and code will pass

through the QTnoise filter.

VibraCall

TM Alert

VibraCall T M is a vibrating alert that notifies that the radio is

receiving a message. This is useful in noisy environments. When

the alert is on, the radio vibrates once every 30 seconds when

you receive a message on the channel and code you set.

1. To turn vibrating alerts on, press until is displayed. The

current setting will flash.

2. Press or to change the setting to On/Off.

3. Press to set or to continue set up.

Keypad Tones

You may enable or disable the speaker key tones. You will hear

the key tone each time a button is pushed.

1. Press until appears. The current setting On/Off will flash.

2. Press either or to turn On or Off.

3. Press to confirm or to continue set up.

Note: When the key tone feature is off, the following are not disabled:

• Transmit timeout alert tone

• Call tone

• Low battery alert tone or

• The transmitted talk confirmation tone

Transmitting a Talk Confirmation Tone

You can set this radio to transmit a unique tone when you finish

transmitting. It is like saying “Roger” or “Over” to let others

know you are finished talking. Talk Confirmation Tone is disabled

in repeater mode on channels 15R-22R.

1. Press until the appears. The current setting On/Off

flashes.

2. Press or to turn On or Off.

3. Press to set or to continue setup.

Auto Power Off

Your radio will save power by automatically turning itself off if

unused after a predetermined amount of time.

1. Press until displays. The current setting (0, 30, 60 or 90)

will flash.

2. Press or to set the time to 30 minutes, 60 minutes or

90 minutes. When this feature is activated, the will remain

on the display.

3. When you exit the Menu mode, the timer will begin. If a

button is pressed, or if there is an incoming signal, the timer

will restart.

4. Press to confirm or to continue set up.

Enabling Repeater Channels

Use of a repeater can greatly increase the radio range and

coverage area. Repeater use must be coordinated with the

owner of the repeater. Be sure to understand and follow the

sharing and usage rules for each repeater system.

See the ”Interference Eliminator Tone / Code Values” table on

overleaf for details on tone frequencies and code values.

1 . Press until the code starts to flash.

2 . Press or to select the code.

3. Press to save the code setting or to continue set up.

You can set a different code for each channel using this

procedure. An extended press of or allows you to scroll

rapidly so you can quickly reach the code you want.

This menu setting for repeater channels 15R-22R is used for

receiving only. The value must match with the repeater output.

Many repeaters will require a value of 0 or OFF. The transmitted

code is set separately and is often required for repeater access.

See on overleaf for”Selecting the Repeater Access (TX) Code”

additional information.

Note: You must set the Interference Eliminator Code to 0 to

communicate with radios that do not have Interference

Eliminator Codes.

Setting and Transmitting Call Tones

This radio can transmit different call tones to other radios in your

group so you can alert them that you want to talk. The radio has

10 call tones from which to choose.

To set a call tone:

1 . Press until the current call tone setting flashes and

appears.

2 . Press or to change and hear the call tone.

3 . Press to set the new call tone or to continue set up.

To transmit your call tone to other radios set to the same

channel and Interference Eliminator Code as your radio,

press .

Note: Setting the call tone to 0 disables the call tone feature.

Hands-Free Use Without Accessories ( )

You can use the iVOX feature to transmit hands-free without the

need for any headset accessories. Once iVOX is turned on, the

radio detects your voice and transmits when you speak into the

internal microphone.

1. Press until appears on the display. The current

setting On/Off will flash.

2. Press or to select On or Off.

3. Press to set or to continue set up.

Hands-Free Use With Accessories ( )

You can transmit hands-free more reliably with the use of

optional headset accessories. Once VOX is turned on, the radio

detects your voice and transmits when you speak.

Many accessories (sold separately) are available for this radio. For

more information, visit our Web site at www.motorola.com or

shop.giantintl.com.

1. Turn the radio off and plug the VOX accessory into the

accessory port.

2. Turn the radio on. VOX shows on the display.

3. Adjust the volume appropriately by pressing or . Lower

the volume before placing the accessory on your head or in

your ear.

4. To turn off, simply remove accessory.

Notes:

• There is a short delay between the time you start talking and when

the radio transmits. There is a short delay before the transmission is

completed.

• The accessory port cover must be tightly in place to

maintain the water tight seal of the radio.

Setting the Sensitivity Level When in Mode

Adjusting the radio’s sensitivity level helps minimize the

possibility of unintended noises triggering a transmission and

helps the radio pick up soft voices.

1. Press until VOX and the level setting (1 - 3) appear on the

display.

2. Press or to select the sensitivity level.

3. Press to set or to continue set up.

3 = High Sensitivity for quiet environments

2 = Medium Sensitivity for most environments

1 = Low Sensitivity for noisy environments

Date : Jan 14, 2011

3MS350 Series

Product specificaties

Merk:	Motorola
Categorie:	Walkie talkie
Model:	MS350R

Heb je hulp nodig?

Als je hulp nodig hebt met Motorola MS350R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Walkie talkie Motorola

Motorola WAVE PTX TLK 110 Handleiding

5 November 2024

Motorola Mag One BPR40 Handleiding

24 September 2024

Motorola Talkabout T72 Handleiding

30 Juli 2024

Motorola Talkabout T110TP Handleiding

29 Mei 2024

Motorola WAVE Mobile TLK 150 Handleiding

17 April 2024

Motorola TALKABOUT T802 Handleiding

22 Februari 2024

Motorola TALKABOUT T803 Handleiding

22 Februari 2024

Motorola T802 Handleiding

18 December 2023

Motorola TLKR T72 Handleiding

3 Juli 2023

Motorola XT185 Handleiding

22 Juni 2023

Handleiding Walkie talkie

Nieuwste handleidingen voor Walkie talkie

GoGEN BOB VYSILACKY Handleiding

30 September 2024

Baofeng UV-82 Handleiding

26 Augustus 2024

Yaesu VX-2R Handleiding

16 Juli 2024

Yaesu FT-4XR Handleiding

16 Juli 2024

Yaesu FT-1500M Handleiding

16 Juli 2024

Yaesu FT-4VR Handleiding

16 Juli 2024

Yaesu FTM-100DR Handleiding

16 Juli 2024

Yaesu FT-2600M Handleiding

16 Juli 2024

Yaesu FTM-7250DR Handleiding

16 Juli 2024

Yaesu FT-65R Handleiding

16 Juli 2024