Motorola MH230R Handleiding

Motorola Walkie talkie MH230R

Lees hieronder de 📖 handleiding in het Nederlandse voor Motorola MH230R (2 pagina's) in de categorie Walkie talkie. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

MH Series

KEM-PK14190-75

Safety and General Information

Important Information on Safe and Efficient Operation

Read This Information Before Using Your Radio.

The information provided in this document supersedes the general

safety information in user guides published prior to December 1, 2002.

Transmit and Receive Procedure

Your two-way radio contains a transmitter and a receiver. To control

your exposure and ensure compliance with the general population/

uncontrolled environment exposure limits, always adhere to the

following procedure:

• Transmit no more than 50% of the time.

• To receive calls, release the PTT button.

• To transmit (talk), press the Push to Talk (PTT) button.

Transmitting 50% of the time, or less, is important because the radio

generates measurable RF energy exposure only when transmitting

(in terms of measuring standards compliance).

Exposure to Radio Frequency Energy

Your Motorola two-way radio complies with the following RF energy

exposure standards and guidelines:

• United States Federal Communications Commission, Code of

Federal Regulations; 47CFR part 2 sub-part J.

• American National Standards Institute (ANSI)/Institute of

Electrical and Electronic Engineers (IEEE) C95. 1-1992.

• Institute of Electrical and Electronics Engineers (IEEE) C95.

1-1999 Edition.

• International Commission on Non-Ionizing Radiation Protection

(ICNIRP) 1998.

• Ministry of Health (Canada) Safety Code 6. Limits of Human

Exposure to Radiofrequency Electromagnetic Fields in the

Frequency Range from 3 KHz to 300 GHz, 1999.

• Australian Communications Authority Radiocommunications

(Electromagnetic Radiation—Human Exposure) Standard, 2003.

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002 “Regulation of

limitation of exposure to electrical, magnetic and electromagnetic

fields in the radio frequency range between 9 KHz and 300GHz”.

To ensure optimal radio performance and make sure human

exposure to radio frequency electromagnetic energy is within the

guidelines set forth in the above standards, always adhere to the

following procedures.

Portable Radio Operation and EME Exposure

Antenna Care

Use only the supplied or an approved replacement antenna.

Unauthorized antennas, modifications, or attachments could

damage the radio and may violate FCC regulations.

Do NOT hold the antenna when the radio is “IN USE.” Holding the

antenna affects its effective range.

Body-Worn Operation

To maintain compliances with FCC/Health Canada RF exposure

guidelines if you wear a radio on your body when transmitting

always place the radio in a Motorola-supplied or approved clip

holder, holster, case or body harness for this product. Use of non-

Motorola-approved accessories may exceed FCC/Health Canada RF

exposure guidelines.

If you do not use one of the Motorola-supplied or approved body-

worn accessories and are not using the radio held in the normal

use position, ensure the radio and its antenna are at least 1 inch

(2.5 cm) from your body when transmitting.

Data Operation

If applicable, when using any data feature of the radio with or

without an accessory cable, position the radio and its antenna at

least one inch (2.5 cm) from the body.

Approved Accessories

For a list of approved Motorola accessories, visit our Web site at

www.motorola.com.

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately shielded,

designed or otherwise configured for electromagnetic compatibility.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received, including

interference that may cause undesired operation.

IC Canada

The term "IC:" before the equipment certification number only

signifies that the Industry Canada technical specifications were met.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts,

turn off your radio in any facility where posted notices instruct you

to do so. Hospitals or health care facilities may be using equipment

that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when onboard an

aircraft. Any use of a radio must be in accordance with applicable

regulations per airline crew instructions.

Medical Devices – Pacemakers

The Advanced Medical Technology Association recommends that

a minimum separation of 6 inches (15 cm) be maintained between a

handheld wireless radio and a pacemaker. These recommendations

are consistent with the independent research by and

recommendations of the U.S. Food and Drug Administration.

People with pacemakers should:

• ALWAYS keep the radio more than 6 inches (15 cm) from their

pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the potential

for interference.

• Turn the radio OFF immediately if there is any reason to suspect

that interference is taking place.

Medical Devices – Hearing Aids

Some digital wireless radios may interfere with some hearing aids.

In the event of such interference, you may want to consult your

hearing aid manufacturer to discuss alternatives.

Medical Devices – Other

If you use any other personal medical device, consult the

manufacturer of your device to determine if it is adequately

shielded from RF energy. Your physician may be able to assist you

in obtaining this information.

Safety and General Use While Driving

Check the laws and regulations regarding the use of radios in the

area where you drive, and always obey them. If you do use your

radio while driving, please:

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a call if

driving conditions so require.

The use of a two-way radio while engaged in activities requiring

concentration may cause distraction or otherwise impair your

ability to safely participate in such activities. Always use technology

safely.

Do not place a portable radio in the area over an air bag or in the

air bag deployment area. Air bags inflate with great force. If a

portable radio is placed in the air bag deployment area and the air

bag inflates, the radio may be propelled with great force and cause

serious injury to occupants of the vehicle.

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially

explosive atmosphere. Only radio types that are especially qualified

should be used in such areas as “Intrinsically Safe.” Do not remove,

install or charge batteries in such areas. Sparks in a potentially

explosive atmosphere can cause an explosion or fire resulting in

bodily injury or even death.

For More Information

For further information, you may call Motorola at 1-800-638-5119

(U.S. and Canada), or e-mail us at giantintl@callcenter.com or visit

us on the Internet at www.motorola.com.

Note: The areas with potentially explosive atmospheres referred to

above include fueling areas such as below decks on boats, fuel or

chemical transfer or storage facilities, areas where the air contains

chemicals or particles (such as grain, dust or metal powders) and

any other area where you would normally be advised to turn off your

vehicle engine. Areas with potentially explosive atmospheres are

often—but not always—posted.

Blasting Caps and Areas

To avoid possible interference with blasting operations, turn off your

radio when you are near electrical blasting caps, in a blasting area,

or in areas posted “Turn off two-way radios.” Obey all signs and

instructions.

Operational Cautions

Antennas

Do not use any portable radio that has a damaged antenna. If a

damaged antenna comes into contact with your skin, a minor burn

can result.

Batteries

All batteries can cause property damage and/or bodily injury such as

burns if a conductive material—like jewelry, keys or beaded chains—

touch exposed terminals. The conductive material may complete an

electrical circuit (short circuit) and become quite hot. Exercise care in

handling any charged battery, particularly when placing it inside a

pocket, purse or other container with metal objects.

Exercise care when removing NiMH or AAA batteries. Do not use

sharp or conductive tools to remove either of these batteries.

Battery Charger Safety Instructions:

Save these Instructions

1. Do not expose the charger to rain or snow.

2. Do not operate or disassemble the charger if it has received a

sharp blow, or has been dropped or damaged in any way.

3. Never alter the AC cord or plug provided with the unit. If the

plug will not fit the outlet, have the proper outlet installed by a

qualified electrician. An improper condition can result in a risk

of electric shock.

4. To reduce the risk of damage to the cord or plug, pull the plug

rather than the cord when disconnecting the charger from the

AC receptacle.

5. To reduce the risk of electric shock, unplug the charger from the

outlet before attempting any maintenance or cleaning.

6. Use of an attachment not recommended or sold by Motorola

may result in a risk of fire, electric shock or personal injury.

7. Make sure the cord is located so it will not be stepped on,

tripped over or subjected to damage or stress.

8. An extension cord should not be used unless absolutely

necessary. Use of an improper extension cord could result in a

risk of a fire and/or electric shock. If an extension cord must be

used, make sure that:

• The pins on the plug of the extension cord are the same

number, size and shape as those on the plug of the charger.

• The extension cord is properly wired and in good electrical

condition.

• The extension cord size is 18 AWG for lengths up to 100 feet,

and 16 AWG for lengths up to 150 feet.

9. The supply cord of the AC adaptor cannot be replaced. If the

cord is damaged, call customer service at 1-800-638-5119 (U.S.

and Canada) or e-mail us at giantintl@callcenter.com.

FCC Licensing Information

Your Motorola radio operates on General Mobile Radio Service

(GMRS) frequencies and is subject to the Rules and Regulations of

the Federal Communications Commission (FCC). The FCC requires

that all operators using GMRS frequencies obtain a radio license

before operating their equipment. To obtain the FCC forms, please

visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home

to source form 605 and 159, which includes all the instructions you

will need.

If you wish to have the document faxed or mailed, or if you have

questions, please use the following contact information:

Changes or modifications not expressly approved by Motorola may

void the user’s authority granted by the FCC to operate this radio

and should not be made. To comply with FCC requirements,

transmitter adjustments should be made only by or under the

supervision of a person certified as technically qualified to perform

transmitter maintenance and repairs in the private land mobile and

fixed services as certified by an organization representative of the

user of those services. Replacement of any transmitter component

(crystal, semiconductor, etc.) not authorized by the FCC equipment

authorization for this radio could violate FCC rules.

3. Gently remove each battery by easing each battery out individually.

4. Reposition the battery cover and press down to secure.

Notes

• Exercise care when removing NiMH or AAA batteries. Do not

use sharp or conductive tools to remove either of these batteries.

• Remove the batteries before storing your radio for extended

periods of time. Batteries corrode over time and may cause

permanent damage to your radio.

Using the Battery Charger (Optional Accessory)

The battery charger provides drop-in charging convenience for

NiMH batteries and can be placed on any flat surface, such as a

desk or workbench. Charge the NiMH battery overnight (at least

16 hours) before using it for the first time. After the initial charge,

an empty battery is fully charged within 14 hours.

1. Follow the steps above to install a NiMH Battery Pack.

2. Plug the AC power supply cord into the jack on the desk stand.

3. Plug the AC power supply into a standard wall outlet.

4. With a radio facing forward, slide it into one of the charging

pockets.

5. When charging in the battery charger, the red light on the

charger base will glow continuously.

Using the mini-USB Charging Connector

The mini-USB charging connector is a handy port that allows you to

conveniently charge your NiMH battery pack. This is an alternative

to charging your NiMH battery pack in the Battery Charger desk

stand using the AC wall adaptor and especially useful when used

while traveling.

Available mini-USB charging options: (Optional Accessories)

1. Wall travel charger

2. Vehicle charger

3. Mini-USB computer cable

If using a computer, the computer must be turned on.

This and other accessories (sold separately) are available for

your radio. For more information, visit our Web site at

www.motorola.com or shop.giantintl.com.

1. Plug your mini-USB cable or charger into a power source as is

appropriate for your accessory.

2. Plug the cable into the mini-USB port on the bottom of your radio.

3. An empty battery will be fully charged in 14 hours.

4. The LED indicator light on the radio will glow to indicate that the

battery is charging.

Notes

• The light will remain red after the NiMH battery pack is fully

charged.

• When moving between hot and cold temperatures, do not

charge the NiMH battery pack until the battery temperature

acclimates (usually about 20 minutes).

• For optimal battery life, remove the radio from the charger within

16 hours. Do not store the radio while connected to the charger.

• If the radio is kept on while charging, the charging time will be

extended.

• Even though the charger is connected, you may not be able to

transmit a message if the battery is completely empty .

Allow time for the battery to charge to 1 bar before

attempting to transmit a message.

Attaching and Removing the Belt Clip

1. Attach belt clip to pocket or belt strap.

2. Align the belt clip post with the hole in the back of the radio.

3. Gently push until the clip clicks in place.

To Remove

1. Push down on the release tab at the top of the belt clip to

release the catch.

2. Pull the belt clip away from the back of the radio.

Turning your Radio On and Off

Turn clockwise to turn the radio on and counterclockwise to

turn the radio off.

1. In the ON position, the radio chirps and briefly shows all feature

icons available on the radio.

2. The display screen then shows the current channel, code and

all features that are enabled.

Setting the Volume

Press and hold for three seconds while rotating until you

reach a comfortable listening level.

1. Rotate clockwise to increase the volume.

2. Rotate counterclockwise to decrease the volume.

Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Talking and Listening

To communicate, all radios in your group must be set to the same

channel and Interference Eliminator Code.

1. To talk, press and hold .

2. When you are finished talking, release .

For maximum clarity, hold the radio two to three inches away from

your mouth and speak directly into the microphone. Do not cover

the microphone while talking.

Talk Range

Your radio is designed to maximize performance and improve

transmission range. Do not use the radios closer than five feet apart.

Monitor Button

Pressing and holding for three seconds allows you to listen to

the volume level of the radio when you are not receiving. This allows

you to adjust the volume, if necessary. You can also press to

check for activity on the current channel before you talk.

Push to Talk Timeout Timer

To prevent accidental transmissions and save battery life, the radio

emits a continuous warning tone and stops transmitting if you

press for 60 continuous seconds.

Menu Options

Selecting the Channel

Your radio has 22 channels. The channel is the frequency the radio

uses to transmit. Channels 8-14 are FRS 0.5 watt only and all other

channels are GMRS. (See the “Channels and Frequencies” table on

overleaf for details.)

1. With the radio on, press . When the radio is on a 0.5 watt

channel, displays. When the radio is on a 1 watt channel,

displays. The current channel flashes.

2. Press or and select an unused or quiet channel.

3. Press to save the channel setting or to continue set up.

Selecting the Interference Eliminator Code

Interference Eliminator Codes help minimize interference by

blocking transmissions from unknown sources. Your radio has 121

Interference Eliminator Codes. Codes 1 – 38 are the standard analog

codes that appear on other FRS/GMRS radios. Codes 39 – 121 are

additional digital codes added for superior interference protection.

0 is the off position, no analog or digital codes are enabled.

To set the code for a channel:

1. Press until the code starts to flash.

2. Press or to select the code.

3. Press to save the code setting or to continue set up.

You can set a different code for each channel using this procedure.

An extended press of or allows you to scroll through

the Interference Code rapidly so you can quickly reach the code

you want.

Note: You must set the Interference Eliminator Code to 0 on a radio

that uses Interference Eliminator Codes to communicate with radios

that do not have Interference Eliminator Codes. Select 0 for “no

tone, no code” and OFF will flash on your radio’s display.

Setting and Transmitting Call Tones

Your radio can transmit different call tones to other radios in your

group so you can alert them that you want to talk. You have 10 call

tones from which to choose.

To set a call tone:

1. With the radio on, press three times until the current

call tone setting (0 - 10) flashes and appears.

2. Press or to change and hear the call tone.

3. Press to set the new call tone or to continue set up.

To transmit your call tone to other radios set to the same channel

and Interference Eliminator Code as your radio, press .

Note: Setting the call to 0 disables the call tone feature.

Hands-Free Use Without Accessories ( )

You can use the iVOX feature to transmit hands-free without the need

for any headset accessories. Once iVOX is turned on, the radio detects

your voice and transmits when you speak into the internal microphone.

1. Press until appears on the display. The current

setting On/Off will flash.

2. Press or to select On or Off.

3. Press to set or to continue set up.

Hands-Free Use With Accessories ( )

You can transmit hands-free more reliably with the use of optional

headset accessories. Once VOX is turned on, the radio detects your

voice and transmits when you speak.

Many accessories (sold separately) are available for your radio.

For more information, visit our Web site at www.motorola.com or

shop.giantintl.com.

1. Turn the radio off and plug the VOX accessory into the

accessory port.

2. Turn the radio on. VOX shows on the display.

3. Adjust the volume appropriately by rotating . Lower the

volume before placing the accessory on your head or in your ear.

4. To turn off, simply remove accessory.

Display Screen Guide

Continued on back

MH Series

Control Buttons

Getting Started

Installing the Batteries

Each radio uses 1 NiMH rechargeable battery pack or 3 AAA

alkaline batteries and beeps when the batteries are low.

Installing NiMH Rechargeable Battery Pack (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover latch

up and remove the cover.

3. Remove the battery pack from the clear plastic bag. (Do not

disassemble or unwrap the battery pack.)

4. Insert the NiMH battery pack with the diagram facing you.

5. Reposition the battery cover and press down to secure.

Installing the Three AAA Alkaline Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery cover latch

up and remove the cover.

3. Insert the three AAA alkaline batteries with + and - polarity as

shown inside.

4. Reposition the battery cover and press down to secure.

Radio Battery Meter

The radio battery icon shows the radio battery charge level, from

full to empty . When the radio has one segment left, the

radio chirps periodically or after releasing (Low Battery Alert).

Removing the NiMH Battery Pack (Optional Accessory)

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

3. Remove the NiMH battery pack by pulling the ribbon attached to

the battery.

4. Reposition the battery cover and press down to secure.

Removing the Three AAA Batteries

1. Turn the radio off.

2. With the back of the radio facing you, lift the battery latch up to

release the battery cover and remove the cover.

For a fax:

Contact the

Fax-0n-Demand

system

For mail service:

Call the FCC

Forms Hotline

If you have

questions about

the FCC License:

Call the FCC

1-202-418-0177 1-800-418-FORM

(3676)

1-888-CALL-FCC

(225-5322)

Two-Way Radio

User’s Guide

Numbers

for Channel,

Call Tone

Numbers

for Codes

Battery Meter

Channel Power

Indicator (see

Menu Options)

Lock

Talk Confirmation

Tone (Roger Beep)

Noise Filtering

On/Off for each

feature

Scan

Call Tone,

Keypad Tone

W eather Alert

Hands-Free Use

Without

Accessories

Hands-Free Use

With Accessories

Push to Talk

Call Tone

Speaker

Menu/Lock

Accessory Jack

Scan/Monitor

Scroll/Weather

Microphone

Volume

Mini-USB

Charging Port

Note: There is a short delay between the time you start talking

and when the radio transmits. There is a short delay before the

transmission is completed.

Setting the Sensitivity Level When in or Mode

Adjusting the radio’s sensitivity level helps minimize the possibility

of unintended noises triggering a transmission and helps the radio

pick up soft voices.

1. Press until VOX/iVOX and the level setting (1-3) appear on

the display.

2. Press or to select the sensitivity level.

3. Press to set or to continue set up.

3 = High Sensitivity for quiet environments

2 = Medium Sensitivity for most environments

1 = Low Sensitivity for noisy environments

Note: When you connect a headset, the radio is automatically set to

the last chosen sensitivity level.

QTNoise Filtering

The QTnoise-filtering feature helps to ensure uninterrupted

communication with other Motorola radios that have this feature.

This feature also filters out unwanted transmissions from other

radios. This is useful in places where there is heavy radio traffic,

such as amusement parks or ski resorts.

Note: QTnoise filtering is not available when the radio is scanning.

To turn QTnoise filtering on or off:

1. Press until displays. The current setting On/Off will flash.

2. Press or to turn noise filtering On or Off.

3. Press to confirm your selection or to continue set up.

To transmit to a radio that has QTnoise filtering turned on:

1. Select the same channel and Interference Eliminator Code as

the other radio.

2. Press to send a call tone. This allows your voice to pass

through the QTnoise filter on the receiving radio.

3. Press and speak normally.

Note: If you skip step 2, the beginning of your message may not be

heard on the receiving radio. For a 30-second period, starting after

the last transmission, all transmissions received on the selected

channel and code will pass through the QTnoise filter.

Keypad Tones

You may enable or disable the speaker key tones. You will hear the

key tone each time a button is pushed.

1. Press until appears. The current setting On/Off will flash.

2. Press either or to turn On or Off.

3. Press to confirm or to continue set up.

Note: When the key tone feature is off, the following are not disabled:

• Transmit timeout alert tone

• Call tone

• Low battery alert tone or

• The transmitted talk confirmation tone

Transmitting a Talk Confirmation Tone

You can set your radio to transmit a unique tone when you finish

transmitting. It is like saying “Roger” or “Over” to let others know

you are finished talking.

1. With the radio on, press until the appears. The current

setting On/Off flashes.

2. Press or to turn On or Off.

3. Press to set or to quit menu mode.

Special Features

Keypad Lock

To avoid accidentally changing your radio settings:

1. Press and hold until displays.

2. When in lock mode, you can turn the radio on and off, adjust

the volume, receive, transmit, send a call tone, and monitor

channels. All other functions are locked.

To unlock the radio, press and hold until is no longer

displayed.

Scanning Channels

Use scan to search the 22 channels for transmissions from

unknown parties, to find someone in your group who has

accidentally changed channels, or to quickly find unused channels

for your own use.

There is a priority feature and 2 modes of scanning (basic and

advanced) to make your search more effective. The basic scan

mode uses the channel and code combinations for each of the 22

channels as you have set them (or with the default code value of 1).

The “Advanced Scan” mode will scan all channels for any and all

codes, detect any code in use, and use that code value temporarily

for that channel.

Priority is given to the “home channel,” that is, the channel (and

Interference Eliminator Code) your radio is set to when you start the

scan. This means the initial channel (and code setting) is scanned

more often than the other 21 channels, and your radio will respond

quickly to any activity occurring on the home channel as a priority.

To start Scanning:

1. Briefly press the key. The scan will appear in the

display, and the radio will begin to scroll through the channel

and code combinations.

2. When the radio detects channel activity matching the channel

and code combination, it stops scrolling and you can hear the

transmission.

3. To respond and talk to the person transmitting, press within

five seconds after the end of the transmission.

4. The radio will resume scrolling through the channels five

seconds after the end of any received activity.

5. To stop scanning, briefly press the key.

To start Advanced Scanning:

1. Set the Interference Eliminator Code to “zero” or OFF.

2. Briefly press the key. The scan will appear in the

display, and the radio will begin to scroll through the channels.

No Interference Eliminator Codes will filter what is heard.

3. When the radio detects channel activity with ANY code (or NO

code), it stops scrolling and you can hear the transmission. Any

Interference Eliminator Code that may be in use by that party

will be detected and displayed.

4. To respond and talk to the person transmitting, press within

five seconds of the end of the transmission. The radio will

transmit using the newly detected Interference Eliminator Code.

5. The radio will resume scrolling through the channels five

seconds after the end of any received activity.

6. To stop scanning, briefly press the key.

Scanning Notes:

1. If you press while the radio is scrolling through inactive

channels, the transmission will be on the “home channel”.

Scanning will resume five seconds after the end of your

transmission. You may press the key to stop scanning

at any time.

2. If the radio stops on an undesired transmission, you may

immediately resume the scan by briefly pressing or .

3. If the radio repeatedly stops on an undesired transmission,

you may temporarily remove that channel from the scan list by

pressing and holding or for three seconds. You may

remove more than one channel in this way.

4. To restore the removed channel(s) to the scan list, turn the radio

off and then back on, or exit and re-enter the scanning mode by

pressing .

5. You cannot remove the home channel from the scan list.

6. In Advanced Scan, the detected code will only be used for

one transmission. You must note the code, exit scan, and set

that detected code on that channel to permanently use the

detected code.

Weather Receiver

Your radio can tune in to broadcasts by the United States National

Oceanic and Atmospheric Administration (NOAA) Weather Radio

and Environment Canada Weatheradio.

You can listen to a weather channel (see “Weather Channels and

Frequencies” table below) or set your radio to alert you to

emergency weather broadcasts that interrupt routine broadcasts.

When you listen to a weather channel, you cannot use your radio

in scan mode or for two-way communications.

Both NOAA and Environment Canada have transmitters located

throughout the United States and Canada, respectively. These

transmitters broadcast watches, forecasts, and other information

24 hours a day.

Note: NOAA weather radio stations are assigned to cover specific

areas and service may be limited. Please check with your local

weather office for frequency and details, or visit www.weather.gov/nwr

in the US or www.msc.ec.gc.ca/msb/weatheradio in Canada to view

the appropriate transmitter for your area.

The use of the NOAA logo does not provide an endorsement or

implied endorsement by NOAA’s National Weather Service, nor

does the use of the Weatheradio logo provide an endorsement or

implied endorsement by Environment Canada.

Turning Weather Channel Reception On and Off

1. To turn weather reception on, press and hold for three

seconds.

2. To turn off, press or turn the radio off and then back on.

Setting the Weather Channel

Your radio receives weather frequencies:

1. After turning weather reception on, press . The current

channel flashes.

2. Press or to select the appropriate channel with good

reception in your area.

3. Press to save the weather channel setting.

Setting the Weather Alert

Your radio can be set to respond to NOAA Weather Radio

emergency messages. A special alarm tone sounds an alert

and turns on the weather receiver to give you immediate weather

and emergency information.

1. After turning weather reception on, press twice. On/Off

displays.

2. Press or to select On/Off. If you activate Weather Alert

and return to two-way mode, will display.

3. Press to save the weather alert setting.

4. Press to return to two-way mode.

As with two-way radio reception, weather channel reception depends

on how close you are to a transmitter and whether you are indoors or

outdoors. Because weather channels are transmitted without codes,

they may contain static or noise. Weather Alert will not function while

actively transmitting or receiving in two-way mode.

Weather Channels and Frequencies

Channel Frequency Description Channel Frequency Description

1 462.5625 MHz GMRS/FRS 12 467.6625 MHz FRS

2 462.5875 MHz GMRS/FRS 13 467.6875 MHz FRS

3 462.6125 MHz GMRS/FRS 14 467.7125 MHz FRS

4 462.6375 MHz GMRS/FRS 15 462.5500 MHz GMRS

5 462.6625 MHz GMRS/FRS 16 462.5750 MHz GMRS

6 462.6875 MHz GMRS/FRS 17 462.6000 MHz GMRS

7 462.7125 MHz GMRS/FRS 18 462.6250 MHz GMRS

8 467.5625 MHz FRS 19 462.6500 MHz GMRS

9 467.5875 MHz FRS 20 462.6750 MHz GMRS

10 467.6125 MHz FRS 21 462.7000 MHz GMRS

11 467.6375 MHz FRS 22 462.7250 MHz GMRS

Products Covered

Products and Accessories as

defined above, unless otherwise

provided for below.

1. Consumer Two-Way Radio

Accessories.

2. Products and Accessories

that are Repaired or

Replaced.

Length of Coverage

One (1) year from the date of

purchase by the first consumer

purchaser of the product unless

otherwise provided for below.

1. Ninety (90) days from the

date of purchase by the first

consumer purchaser of the

product.

2. The balance of the original

warranty or for ninety (90)

days from the date returned

to the consumer, whichever

is longer.

Exclusions

Normal Wear and Tear. Periodic maintenance, repair and

replacement of parts due to normal wear and tear are excluded

from coverage.

Batteries. Only batteries whose fully charged capacity falls below

80% of their rated capacity and batteries that leak are covered by

this limited warranty.

Abuse & Misuse. Defects or damage that result from: (a) improper

operation, storage, misuse or abuse, accident or neglect, such as

physical damage (cracks, scratches, etc.) to the surface of the

product resulting from misuse; (b) contact with liquid, water, rain,

extreme humidity or heavy perspiration, sand, dirt or the like, extreme

heat, or food; (c) use of the Products or Accessories for commercial

purposes or subjecting the Product or Accessory to abnormal usage

or conditions; or (d) other acts which are not the fault of Motorola or

Giant International Ltd., are excluded from coverage.

Use of Non-Motorola branded Products and Accessories. Defects

or damage that result from the use of Non-Motorola branded or

certified Products, Accessories, or other peripheral equipment are

excluded from coverage.

Unauthorized Service or Modification. Defects or damages

resulting from service, testing, adjustment, installation,

maintenance, alteration, or modification in any way by someone

other than Motorola, Giant International Ltd. or its authorized

service centers, are excluded from coverage.

Altered Products. Products or Accessories with (a) serial numbers

or date tags that have been removed, altered or obliterated; (b)

broken seals or that show evidence of tampering; (c) mismatched

board serial numbers; or (d) nonconforming or non-Motorola

branded housings, or parts, are excluded from coverage.

Communication Services. Defects, damages, or the failure of

Products or Accessories due to any communication service or

signal you may subscribe to or use with the Products or

Accessories is excluded from coverage.

Warranty

Consumer Two-Way Radio Products and Accessories purchased in

the United States or Canada.

What Does this Warranty Cover?

Subject to the exclusions contained to the right, Giant International

Ltd. warrants the Motorola branded consumer two-way radios that

operate via Family Radio Service or General Mobile Radio Service

that it manufactures (“Products”), the Motorola branded or certified

accessories sold for use with these Products that it manufactures

(“Accessories”) to be free from defects in materials and

workmanship under normal consumer usage for the period(s)

outlined below. This limited warranty is a consumer’s exclusive

remedy, and applies as follows to new Motorola branded Products

and Accessories manufactured by Giant International Ltd., and

purchased by consumers in the United States or Canada, which are

accompanied by this written warranty:

Who is covered?

This warranty extends only to the first consumer purchaser, and is

not transferable.

What will GIANT INTERNATIONAL LTD. do?

GIANT INTERNATIONAL LTD., at its option, will at no charge repair,

replace or refund the purchase price of any Products or

Accessories that does not conform to this warranty. We may use

functionally equivalent reconditioned/ refurbished/ pre-owned or

new Products, Accessories or parts.

How to Obtain Warranty Service or Other Information?

To obtain service or information, please call:

USA Two-Way Radios Canada Two-Way Radios

1-800-638-5119 1-800-638-5119

giantintl@callcenter.com giantintl@callcenter.com

For Accessories, please call the telephone number designated

above for the product with which they are used.

You will receive instructions on how to ship the Products or

Accessories at your expense, to a GIANT INTERNATIONAL LTD.

Authorized Repair Center. To obtain service, you must include: (a) a

copy of your receipt, bill of sale or other comparable proof of

purchase; (b) a written description of the problem; (c) the name of

your service provider, if applicable; (d) the name and location of the

installation facility (if applicable) and, most importantly; (e) your

address and telephone number.

What Other Limitations Are There?

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE

DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,

REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS

LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE

CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL

MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE, WHETHER

IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES

IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR

ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE

OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR

OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION

WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR

ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE

DISCLAIMED BY LAW.

Some states and jurisdictions do not allow the limitation or

exclusion of incidental or consequential damages, or limitation on

the length of an implied warranty, so the above limitations or

exclusions may not apply to you. This warranty gives you specific

legal rights, and you may also have other rights that vary from state

to state or from one jurisdiction to another.

Patent and Copyright Information

Manufactured, distributed or sold by Giant International Ltd., official

licensee for this product. Motorola, the Stylized M Logo, and other

Motorola trademarks and trade dress are owned by Motorola, Inc.

and are used under license from Motorola, Inc. MOTOROLA and the

Stylized M Logo are registered in the US Patent & Trademark Office.

All other product or service names are the property of their

Please contact customer service at 1-800-638-5119 or e-mail us at

giantintl@callcenter.com for questions/comments, warranty, support

or service related to this product.

MH Series

Channels and Frequencies

Weather

Channel Frequency Weather

Channel Frequency

WX1 162.550 MHz WX7 162.525 MHz

WX2 162.400 MHz WX8 161.650 MHz

WX3 162.475 MHz WX9 161.775 MHz

WX4 162.425 MHz WX10 161.750 MHz

WX5 162.450 MHz WX11 162.000 MHz

WX6 162.500 MHz

Product specificaties

Merk:	Motorola
Categorie:	Walkie talkie
Model:	MH230R

Heb je hulp nodig?

Als je hulp nodig hebt met Motorola MH230R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Walkie talkie Motorola

Motorola WAVE PTX TLK 110 Handleiding

5 November 2024

Motorola Mag One BPR40 Handleiding

24 September 2024

Motorola Talkabout T72 Handleiding

30 Juli 2024

Motorola Talkabout T110TP Handleiding

29 Mei 2024

Motorola WAVE Mobile TLK 150 Handleiding

17 April 2024

Motorola TALKABOUT T802 Handleiding

22 Februari 2024

Motorola TALKABOUT T803 Handleiding

22 Februari 2024

Motorola T802 Handleiding

18 December 2023

Motorola TLKR T72 Handleiding

3 Juli 2023

Motorola XT185 Handleiding

22 Juni 2023

Handleiding Walkie talkie

Nieuwste handleidingen voor Walkie talkie

Oregon Scientific TP668 Handleiding

14 December 2024

Midland G11 Pro Handleiding

12 November 2024

Midland XT50 Pro Handleiding

12 November 2024

Midland XT30 Pro Handleiding

12 November 2024

Midland XT10 Pro Handleiding

12 November 2024

Midland XT70 Pro Handleiding

12 November 2024

GoGEN BOB VYSILACKY Handleiding

30 September 2024

Baofeng UV-82 Handleiding

26 Augustus 2024

Yaesu VX-2R Handleiding

16 Juli 2024

Yaesu FT-4XR Handleiding

16 Juli 2024