Moog Sirin Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Moog Sirin (32 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/32
SAVE TO A NEW LOCATION:
GLIDE + RELEASE
(LEDs begin flashing)
SAVE PRESET:
GLIDE + RELEASE
(Press RELEASE to cancel without saving)
SELECT A PRESET LOCATION:
GLIDE + OSCILLATOR 1 or 2
1. 3.2.
SIRIN CHEAT SHEET
FREE EDITOR/LIBRARIAN
Access and automate every parameter on and under the hood of your Sirin right from your DAW.
Get the free Editor/Librarian software when you register your Sirin at Moogmusic.com/register
STORE AND CHANGE PRESETS
Up to 128 presets can be saved and loaded onto your Sirin using the free Editor/Librarian software.
Sirin also supports MIDI Program Change messages, allowing almost any MIDI controller to change
presets on your Sirin.
MODULATION SOURCES
Select from 6 different modulation sources: Triangle, Square, Ramp, Saw, Sample & Hold and Filter
EG (MIDI CC 85)
HARD SYNC
VCO 2 Hard Sync allows a number of sounds to be created with Sirin (MIDI CC 80)
OSCILLATOR 2 MODULATION
Send modulation to Oscillator 2 only – ideal for use with Hard Sync (MIDI CC 112)
CV MAPPING
Your Sirin’s Pitch and Volume CV inputs can be re-mapped to control any parameter on your Sirin,
while the Gate input can be re-mapped to alter the state of any on/off parameters like Oscillator
waveshape.
NOTE: All CV Mapping is configured in the free Sirin Editor/Librarian software.
CV TO MIDI CONVERSION
Sirin can convert multiple channels of Control Voltage to MIDI. This allows you to take CV sources
like a Moog Mother-32 and translate the voltage into MIDI for CV control over plug-in effects, soft
synths, or other MIDI gear.
WARNING: For optimal CV to MIDI conversion response, adjust the scale and range of the external
control voltage to stay within 0 to +5 Volts. Do not apply a negative control voltage, or a CV
greater than +5 Volts!
NEXT PRESET:
GLIDE + OSCILLATOR 1 WAVE
PREVIOUS PRESET:
GLIDE + OSCILLATOR 2 WAVE
SAVE CURRENT PRESET:
GLIDE + RELEASE
(Hold both for 1 second).
VCO 2 BEAT FREQUENCY:
GLIDE + VCO 2 FREQ
EXT. INPUT LEVEL:
GLIDE + VCO 1 LEVEL
EG TRIGGER MODE:
GLIDE + AMP EG ATTACK
FILTER EG DELAY TIME:
GLIDE + FILTER EG ATTACK
VCO 2 MOD ONLY ON/OFF:
GLIDE + VCO LFO AMT
TOP OCTAVE WRAP ON/OFF:
GLIDE + GLIDE RATE
FILTER EG HOLD TIME:
GLIDE + FILTER EG DECAY/RELEASE
PANIC/ALL NOTES OFF:
GLIDE + AMP EG SUSTAIN TO ZERO.
DRONE ON/OFF:
GLIDE + AMP SUSTAIN (Min to Max = ON)
GLIDE + AMP SUSTAIN (Max to Min = OFF)
MOD SOURCE SELECTION:
GLIDE + LFO RATE
HARD SYNC ON/OFF:
GLIDE + VCO 2 LEVEL
SHIFT PANEL FUNCTIONS QUICK REFERENCE GUIDE
The switch on your Sirin can act as a “shift” key, allowing quick access to a number GLIDE
of extended functions directly from the panel.
DECAY/RELEASE MODES
Press and hold the RELEASE switch for 1 second to change modes. The switch LED will blink one RELEASE
time to indicate Mode 1, or two times to indicate Mode 2.
MODE 1: Decay and Release times are linked and the switch enables or disables the Release RELEASE
stage of the envelope.
MODE 2: Decay and Release times are independent. If is lit, the RELEASE DECAY/RELEASE knob is
editing Release time. If is dark, the RELEASE DECAY/RELEASE knob is editing Decay time.
AMP EG HOLD TIME:
GLIDE + AMP EG DECAY/RELEASE
SIRIN


Product specificaties

Merk: Moog
Categorie: Niet gecategoriseerd
Model: Sirin

Heb je hulp nodig?

Als je hulp nodig hebt met Moog Sirin stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Moog

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd