Mooer Tone Capture GTR Handleiding

Mooer Niet gecategoriseerd Tone Capture GTR

Lees hieronder de 📖 handleiding in het Nederlandse voor Mooer Tone Capture GTR (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 186 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
1. Footswitch:
• Switch On/Off
• Sampling
2. RED/BLUE LED Button ：
• Press to select sampling mode, presets.
3. LED indicator:
•Indicates the current slot
4. Output:
mono jack.•¼
5. Input:
mono jack.•¼
6. TREBLE
•Adjust High frequency
7. MID SHIFT:
•Adjust Mid frequency adjustment
8. BASS:
•Adjust Low frequency
9. MID:
•Adjust Mid frequency
10. LEVEL:
•Volume control
12. USB port:
•Connect to the PC for firmware
update via USB cable.
11. DCIN:
Connect a 9V DC 200mA •
Centre pin negative
power supply
Power Supply
Please connect the designated AC adapter to an AC outlet of the correct volta ge.
Be sure to only us e an AC adapter which supplies 9V DC, 200m A .
Unplug the AC po wer adapter when not in use or during elec tr ical storms.
FCC certification
This device complies with Part 1 5 of t he FCC Rules. Operation is subject
to the followi ng two conditions:
Thi s device may not cau se h armful interference.
This device must accept any interference received, including interference
that may cause u ndesired opera ti on.
Location
To avoid defor mation, discol or ation, or other serious damage, do not
expose this un it to the following conditions:
Direct sunli ght Heat sources
Magnetic fields Extreme temp erature or humid it y
Excessive dusty or dirty locati on High humidity or moisture
Strong vibra tions or shocks
Radio Freque ncy Interference
Radios and televisions place d nearby may experience reception i nt erference.
Operate this u nit at a suitable di stance from radios and televisions.
Cleaning
Clean only with a soft, dry cloth. If n ecessary, slightly moisten the cloth.
Do not use abras ive cleanser, cl ea ning alcohol, pa in t thinners, wax,
solvents, cl eaning fluids, o r ch emical-impregnated wiping clo th s.
Can capture un ique guitar tona l qualities throug h sampling technol og y.
Can be used as an in dividual EQ peda l.
7 preset slots t o store EQ and sampled guitar sounds.
Switch betwe en TRUE BYPASS or BUF FER BYPASS.
Firmware upgradeable via USB .
Main Feature
Layout Instructions
•Power on the pedal, press the LED button to choose a preset slot. If there is already
a stored preset file, the LED indicator will stay red. If the slot is blank, the LED
indicator will blink.
•The TONE CAPTURE Guitar Pedal can sample any guitar, provided it has some form
of pickup, and create a detailed digital Guitar model using MOOER’s proprietary non-
linear IR technology. This is achieved by comparing the differences between the
“SOURCE” (the guitar you want to use) and the guitar being sampled or the “TARGET”
(the guitar you want it to sound like). A complex calculation then ensues and an
uncanny digital recreation of your “TARGET” guitar tone is born. Activating the TONE
CAPTURE with your newly created guitar model will instantly transform the tone of your
“SOURCE” into that of your “TARGET”. The guitar model can then be tweaked even
further for use with other “SOURCE” instruments or even to create something completely
new.
GTR CAPTURE
•After powering on, connect the TARGET guitar (the guitar you intend to sample),
then press and hold the footswitch. The button light will turn red indicating it is in
the TARGET acquisition mode. Press the footswitch again, and TARGET sampling
begins indicated by the the LED indicators illuminating in order. During this process,
we recommend playing an open chord first and then playing across the full range of
the instrument. (The wider the coverage, the better the result will be.) When all 7
LEDs are lit and the light stops flashing, the sampling window is closed. Pressing
the switch during or after sampling can terminate the sampling process. Press the
switch again to start the sampling process over. If you are not happy with the sample,
press the switch again to star t over.
TARGET
•Press the LED button, it will turn blue to enter the SOURCE sampling mode.
Connect the INPUT to the guitar you want to use with the TARGET sample (SOURCE).
Short press the switch to start SOURCE capture. Again, we recommend playing an open
chord first and then playing across the full range of the instrument or play as close as
possible to what was played in TARGET mode. Pressing the switch during the sampling
process can terminate the sampling process. Press the switch again to start sampling
again and after the sampling is finished, press the switch to resample.
SOURCE
MUTE
•After SOURCE and TARGET are sampled, press and hold the footswitch to
mute the output.
Savin g
•After the SOURCE sampling is finished, press the LED button to confirm the sampling
result and choose a save slot. At this time, the LED indicator will start to flash to indicate
the current slot. Press and hold the LED Button to save the sampling file.
Delete
•The sampling files can be deleted by pressing the LED Button while the effect is off.
The LED flashes quickly and stops, indicating that the deletion is completed.
TRUE/BUFFER BYPASS
•Unplug the power supply. Press and hold the footswitch while powering on the unit.
When the LED indicator lights up in ascending order (1-7), the pedals is in buffer
bypass mode. If the LED indicator lights up in descending order (7-1), the pedal
is in true bypass mode.
Factory reset
• Unplug the power supply, press and hold the LED Button, then power on.
The pedal will reset.
Firmware update
•Unplug the power supply, press and hold the footswitch and LED
Button simultaneously, power on the pedal to enter firmware update mode.
Instructions
Input: 1/4" mono jack (impedance 2.2M Ohms)
Output: 1/4" mono jack (impedance 100Ohms)
Power suppl y: 9V DC transformer (internal negative external), MOOER Micro
Power is recommended
Current Draw: 200mA
Dimensions: 93.5mm(D) x 42mm(W) x 52mm(H)
Weight: 155g
Accessories: User Manual
*Disclaimer: Parameters may update without notice.
1
8
5
7
6
11
9
2
4
USB
12
3
10
Parameter saving and editing
电源供应
请使用正确的交流电源插座连接电源变压器。
请使用内负外正 的 电源变压器，否则将会导致设备损坏，着火或者其他问题。9V
不使用时或雷雨天时请拔下电源。
连接
连接设备或断开连接前，请务必关闭电源及其他设备，避免故障和损害其他设
备。另外，移动本机前请断开所有连接线及电源线。
放置场所
为防止变形、变色，及其他严重损坏，请避免以下情况：
•阳光直射 •靠近热源
•磁场 •高温潮湿
•多尘或不洁的地方 •湿度较大
•强烈震动或摇晃
电器干扰
在使用本机时，请确保使用时远离收音机和电视机，以免造成干扰。
清洁
清洁本机时，请使用干燥柔软或稍微湿润的抹布。请勿使用粗糙的清洁粉、酒精、
涂料稀释剂、蜡、溶剂、清洁剂及化学试剂等浸渍擦拭。
操作
请勿暴力使用开关及控制元件。
请勿让纸屑、金属制品及其他物体落入机内。
请勿摔落以及让本机受到冲击和过度按压。
可以通过采样学习捕获不同的吉他音色
可以作为独立的 效果器使用EQ
提供 个预置位置存储 以及采样的吉他音色7 EQ
可切换 或者TRUE BYPASS BUFFER BYPASS
可通过 进行固件升级USB
1. 踩钉：
开关效果器以及进行采样学习操作
2. 双色带灯按键：
指示灯具有蓝红双色提示及关闭状态
PRESET capture切换、保存以及 采集模式切换
3. LED 指示灯：
通过闪烁亮灭状态提示不同的功能操作
4. OUTPUT输出：
1/4”单声道音频接口，连接输出信号
5. INPUT输入：
1/4”单声道音频接口，连接输入信号
6. TREBLE旋钮：
高频调节
7. MID旋钮：
中频调节
8. BASS旋钮：
低频调节
9. MID SHIF T旋钮：
中频扫频范围调节
10. LEVEL旋钮：
音量调节
12. USB接口：
可连接电脑进行固件升级
11. 电源接口
9V使用 直流变压器
（内负外正 ， ）200mA
在 和 阶段，采样失败或直接跳过学习阶段等非正常操作将对最后的学习TARGET SOURCE
结果产生影响。建议按正常的步骤和方法来操作得到你想要的学习结果。
操作说明
开启效果器，使用带灯按键选择一个预置位置，如果该预置位置有保存音色文件， 灯为长亮；LED
如果没有保存音色文件， 灯则为缓慢闪烁。调整参数后长按带灯按键， 灯快速闪烁后停止LED LED
即保存成功。（ 长亮状态下改变参数 会闪烁提示参数已发生改变）LED LED
GTR CAPTURE
1. TARGET
连接电源开机后，连接你想获得音色的吉他（TARGET）。长按踩钉，此时按键灯变为红色提示进入
TARGET LED采集模式。再次短按踩钉， 指示灯会逐个点亮提示开始采集。在此过程中任意弹奏一段
乐句，（覆盖的音域越广效果就会越好）直到 个 指示灯全部点亮闪烁停止，采样完成。7 LED
采样过程中按下踩钉可终止采样进程，再次按下踩钉重新开始采样；采样结束后可按下踩钉重新采样。
SOURCE TARGET MUTE和 采样完成后长按踩钉可激活 功能（可避免拔插吉他连接线带来的冲击声）
3. MUTE
5. 储存音色
SOURCE LED采样结束后短按带灯按键即生成学习结果并进入采样储存模式。此时 会开始闪烁提示
当前储存位置，长按带灯按键， 指示灯快速闪烁后长亮即保存成功。切换通道或者短按踩钉即LED
放弃本次学习。
参数调整以及保存
2. SOURCE
短按带灯按键,按键灯变为蓝色提示进入 采集模式。SOURCE
请将 与您常用的吉他（ ）连接。短按踩钉开始 采集，弹奏一段与INPUT SOURCE SOURCE TARGET
采集时较为接近的乐句，乐句越相似，采样学习结果越好。采样过程中按下踩钉可终止采样进程，
再次按下踩钉重新开始采样；采样结束后可按下踩钉重新采样。
SOURCE EQ采样结束后，可以通过面板的旋钮对音量以及 进行调整以达到预期的音色。
4. 音色调整
6. 删除音色
在选择的预置音色位置关闭效果器，长按带灯按键，LED灯快速闪烁后停止即提示已删除该位置
存储的音色文件。
BYPASS 模式切换
断开单块的电源，按住踩钉不放同时连接电源。根据开机时 闪烁的次序可判断即将切换的LED
BYPASS 1-7 BUFFER BYPASS; 7-1 TRUE BYPASS模式。 顺序时，为 顺序时，为 。默认设置为
TRUE BYPASS BUFFER BYPASS。效果器链较长时，建议使用 模式减少信号损失。
输入: 1/4” 2.2M Ohms单声道音频接口（阻抗 ）
输出: 1/4” 100Ohms单声道音频接口（阻抗 ）
电源供给: 9V Mooer Micro Power直流变压器（内负外正 ），推荐使用
工作电流: 200mA
尺寸: 93.5mm(D) x 42mm(W) x 52mm(H)
重量: 155g
附件: 用户手册
*免责声明：参数更新恕不另行通知。
恢复出厂设置
断开电源按住带灯按键，再连接电源开机，松开按键后， 灯会全部闪烁然后停止即恢复出厂LED
设置，此时将清除所有用户保存的音色。
固件升级
断开电源时，按住按键灯和踩钉，再连接电源开机，将进入固件升级模式，可以连接电脑进行
固件升级操作。
智能吉他听感捕获单块
1
8
5
7
6
11
4
USB
12
3
10
9
2

Product specificaties

Merk: Mooer
Categorie: Niet gecategoriseerd
Model: Tone Capture GTR

Heb je hulp nodig?

Als je hulp nodig hebt met Mooer Tone Capture GTR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Mooer

Mooer

Mooer PRIME S1 Handleiding

6 April 2024
Mooer

Mooer MICRO DI Handleiding

9 Juli 2023
Mooer

Mooer Echolizer Handleiding

9 Juli 2023
Mooer

Mooer Noise Killer Handleiding

8 Juli 2023
Mooer

Mooer Echoverb Handleiding

8 Juli 2023
Mooer

Mooer Solo Handleiding

8 Juli 2023
Mooer

Mooer 019 Handleiding

7 Juli 2023
Mooer

Mooer Micro Aby MK2 Handleiding

7 Juli 2023
Mooer

Mooer Triangle Buff Handleiding

7 Juli 2023
Mooer

Mooer Ultra Drive MKII Handleiding

6 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024