Monacor ELAX-2812BPTZ Handleiding

Monacor Bewakingscamera ELAX-2812BPTZ

Lees hieronder de 📖 handleiding in het Nederlandse voor Monacor ELAX-2812BPTZ (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Mini PTZ ameraC

ELAX-2812BPTZ

Packing details

Camera 1 PCS

1 PCS

Details NO

Manual

2.1 Cable interface

4IN1 Bullet PTZ Camera support with UTC (Video coaxial

control) ,support with 4 video mode output

(AHD ,TVI ,CVI ,CVBS ) , setting via DIP Switch

You can refer to the following figure for multiple function

combination cable informationSee Figure 2-1. there might

be some differences among different serial products

2-2 Cable function explain

2-1 Cable Draft

Power connector

input DC 12V Power

Power

Video

DIP Switch

Video connector

Setting mode with video

NO Connector Function

AHD

TVI

CVI

CVBS

Equipment connect

Quick installation guide

V1.0.0

PREFACE

Important Safety Notices

Summary：

Document describes unpacking inspection device structures

installation and quick configuration tool in details

Signal instruction：

These symbols may appear with meanings as following

The following contents are specification for using the

devices correctly please read these notices and warnings

carefully and obey while using it

Attention：

1.1 Power

1.2 Environment

All installation and operation here should conform to your

local electrical safety codes

Only use a regulated 12 V power supply unit with a

minimum rating of 2 A.

Please protect cable being trampled power or squeezed

especially in the socket, and exit Junction

Avoid focusing on highlight (such as the sun or lights),

otherwise it may cause over explosion phenomenon (this is

not device's problem) or may damage camera's

CMOS.

Please transport and store t under allowable , use he camera

temperat humidityrange. Do not put the device under e and

wet, dusty extremely hot or cold, strong electromag

netic radiation or unstable lighting conditions etc.

Prevent water or other liquid falling into the camera.

P .lease keep the ventilation around the device

No heavy ion or er splash stress, violent vibrat wat are

allowed during the transportationand storage.

When transporting camera, it use company the should

packing or use same quality ma terial packing.

Thunder-proof device to is recommended be adopted

for preventing thunder better.

Special explanation

1.3 Operation and maintenance

Do not dismantle the camera no components inside since

which can be repaired by users.

Do not touch optic the CMOS component directly you can

use the blower to clean the dust on the lens surface If

necessary, clean the dust with please gently dry clothwhich

is slightly wet with alcohol.

Please use For heavy dirt, soft cloth to clean the device.

please put little detergent on thecloth to clean and dry. Do

not use volatile solvent, Alcohol, Benzene or Diluent-such as

sor irritant and abrasiveness cleanser to clean the device.

Otherwise, it will damage the device or weaken camera

working performance.

The material of front cover is optic component please do not

t ouch or clean the surface directly.For cleaning, please

use professional optical cleaning method Inadaptable

cleaning method (e. g. cleaning directly with cloth ) may

result harmful effect on theinfrared function of the in a

camera.

Warning:

Be sure to use all the accessories recommended by

manufacturer and theinstallation and repairs should be

conducted by professionals.

Please make sure the CMOS component is out of

the radiation of laser beam devices. Otherwise it may result

in damage on the component.

Because our company continuously adopts new technolo-

gies product parameterschange without prior notice. Some

function of products may have slight differenceafter the

updates.

For receiving the latest procedures and additiona linstruction

document please contact the company s customer service

department.

If there are any problems while using the camera, please feel

free to contact the supplier or the company's customer

service department.

Because of the real environment and other unstable factors,

some data may be differ-ent with instruction guide. If there

are any questions and disputes please regard the

Company's final explanation as the criterion.

Please follow instruction guide, we are not liable for any

problems caused byman-made damage

This manual is for reference only. slight difference may be

found in users interface

1.1 Checking Steps

When user received the bullet PTZ Camera, please check

whether it has obviously damage on the appearance of

equipment Packing material can stand accidental Crash on

transport. Please open the package and check all the

components are included. Please reference the following

form.

1.2 Accessories

Be sure to use all the accessories recommended by manufac-

turer

Checking Box

Bracket change

The wall wight for install the camera ,must be can stand 3

times as much as the camera .

Pls Choose cleanly ,smooth wall .Drilled hole according with

the bracket hole . Putting with the bulged tubeThen Fixed

the camera under the ceiling .

Pls Choose cleanly ,smooth wall .Drilled hole according with

the bracket hole . Putting with the bulged tube

The fault of the bracket is walled mounted ,For ceilling

mounted ,if need,change it by urself . As picture ,take out 2

bolts ,motion the bracket with180

2.2

Structure size

(Unit: mm)

2-4 Dimension

2-5 Dimension

2-3 Dimension

3-1 Draft dimension

3-2 Dimension

4-1 Equipment change draft

Wall mounted

Ceiling

IR sensitivity

setting

IR Mode setting

call 95

set 71 call N

set 70 call N N : 1.Auto 2,Open ,3 close

Range of settings 1-10

10 = highest sensitivity level

5Factory default

Reset /restart

call 82 or call 62

call 94 or call 74

NO Function command explain

Equipment Install

180°

Take out bolts put on bolt

PTZ control is made via the PTZ menu of the recorder

connected (control protocol "Coax").

To show the camera menu, call up the preset 95.

Camera setting

1、LENS MANUAL

2、EXPOSURE ←

3、BACK LIGHT OFF

4、WHITE BAL ATW

5、DAY&NIGHT COLOR

6、 ←NR

7、SPECIAL ←

8、ADJUST ←

9、 SAVE&END ←EXIT

Setting

1、LENS MANUAL

2、EXPOSURE ←

3、BACK LIGHT OFF

4、WHITE BAL ATW

5、DAY&NIGHT COLOR

6、 ←NR

7、SPECIAL ←

8、ADJUST ←

9、 SAVE&END ←EXIT

1、 ←SHARPNESS AUTO

2、 ←MONITOR LCD

3、LSC ON

4、VIDEO/OUT NTSC

5、 ←RETURN RET

ADJUST

Appendix

Set

ting

5 Main menu-1

5 2 Submenu ADJUST-

When all settings have been made, use EXIT

to exit the menu.

Product specificaties

Merk:	Monacor
Categorie:	Bewakingscamera
Model:	ELAX-2812BPTZ
Kleur van het product:	Wit
Gewicht:	385 g
Diepte:	168 mm
Soort:	IP-beveiligingscamera
Gebruikershandleiding:	Ja
Bluetooth:	Nee
Vormfactor:	Rond
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad en draadloos
Ethernet LAN:	Nee
Montagewijze:	Plafond/muur
Ondersteunde video-modi:	1080p
Maximum resolutie:	1920 x 1080 Pixels
Totaal aantal megapixels:	2 MP
Diameter:	68 mm
Type stroombron:	DC
Stroomuitvoer (volt):	12
Stroomuitvoer (ampère):	0.8 A
Minimale belichting:	0.01 Lux
Aantal cameras:	1
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Video bewegings-detectie:	Ja
Brandpuntbereik:	2.8 - 12 mm
Omvang optische sensor:	1/2.9 "
Type beeldsensor:	CMOS
Optische zoom:	4 x
PTZ control:	Ja
Pan bereik:	0 - 180 °
Dag/nacht modus:	Ja
Aantal lenzen:	1
Controle camerapanning:	Ja
Kantelfunctie camera:	Ja
Draai-snelheid:	10 °/sec
Pan snelheid:	20 °/sec
BNC output ports:	1
Aantal sensoren:	1
Nachtkijker afstand:	25 m
Aantal verlichtingen LEDS:	6
Achtergrondverlichting compensatie:	Ja
Wifi:	Nee
Bedrijfstemperatuur (T-T):	0 - 50 °C
Bereik kantelhoek:	0 - 55 °
Privézone maskeren:	Ja
Digital Wide Dynamic Range (DWDR):	Ja