Mitsubishi XL6600U Handleiding

Mitsubishi Beamer XL6600U

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Mitsubishi XL6600U (8 pagina's) in de categorie Beamer. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
1
LCD Projector
XL6600U/XL6500U
Controlling the projector using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
PC-controllable functions:
β€’ Turning the power ON or OFF
β€’ Changing input signals
β€’ Inputting commands by pressing the buttons on the control panel and remote control
β€’ Menu setting
Connection
RS-232C cable SERIAL
D-SUB 9-pin D-SUB 9-pin
To RS-232C
terminal
Important:
β€’ Connect the computer with the projector on a one-to-one basis.
β€’ Make sure that your computer and projector are turned off before connection.
β€’ Boot up the computer fi rst, and then plug the power cord of the projector.
(If you do not follow this instruction, the Com port may not function.)
β€’ Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1. Interface
1.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)
Pin No. Name I/O
1 OPEN
2 RXD IN
3 TXD OUT
4 OPEN
5 GND
6 OPEN
7 OPEN
8 OPEN
9 OPEN
1.2 Communications format
PROTOCOL RS-232C
BAUD RATE 9600 [bps]
DATA LENGTH 8 [bits]
PARITY BIT NONE
STOP BIT 1 [bit]
FLOW CONTROL NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable, the reverse type cable should be used.
2
2. Control command diagram
The command consists of the address code, function code, data code, and end code. The length of the command
varies among the functions.
Address code Function code Data code End code
ASCII β€˜30h’ 30h’ Function Data β€˜0Dh’
Character 00 Function Data
[Address code] 00 (In ASCII code, β€˜30h’ β€˜30h’) fi xed.
[Function code] A code of each fi xed control move.
[Data code] A code of each fi xed control data (number) and not always indicated.
[End code] (In ASCII code, β€˜0Dh’) fi xed.
3. Control sequence
Computer Projecto
r
1
2
3
4
Sequence Note
1Send the command from the
personal computer to the projector.
2
The projector will send a return
command after it receives an end
code.
If the projector does not receive commands
normally, that is, if the projector is not connected
physically or unable to receive commands, it does
not send out a return command.
The projector sends out a return command within
one second at the latest.
3
The personal computer checks the
command and confi rms if the sent
command has been received or not.
Although the projector receives the commands, it
in some cases does not execute the commands.
4
Use the check command to see
if the projector has executed the
command.
This projector sends various codes other than the
return code. When having a control sequence by
RS-232C, reject other codes from the personal
computer.
β€’ Although the projector sends out the return command, the command may not take effect in the following
cases.
(1) During signal switching
(2) In the process of the auto position
(3) After the power is turned on.
The projector receives no commands for about 20 seconds (or for 2 minutes at the longest if the lamp
does not light up promptly as the life is expiring.)
β€’ When sending commands successively, wait to receive the return command of the current command before
sending a next command.
β€’ The projector may not receive a command when the splash screen is being displayed immediately after turn-
ing on the power. Use command β€œ00r10” to cancel the splash screen.
β€’ While using the LAN terminals, the LAN functions take precedence.
β€’ For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number 63007) are
available. Note, however, that the response becomes slightly slower than when using the RS-232C terminals.
[Example] When turning the power ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector Description
β€˜30’ β€˜30’ β€˜21’ β€˜0D’
00!
Command for POWER ON
β€˜30’ β€˜30’ β€˜21’ β€˜0D’
00!
Command receipt confi rmation
(Command echo back)
β€’ The fl owchart on the next page shows the recommended operating sequence for your reference to create a
program.
3
Sending out command
Awaiting response
from projector
Awaiting response
from projector
Checking execution of
command (sending out
check command)
Sending command again
No
YesYes
Yes
1
1
10th trial
Less than
10 times
Projector error
Send out β€œ00vER” to check error details.
Recover from error state.
0–3
To normal operation 4
Enter password.
Send out β€œ00PASS****.”
Projector is functioning.
Use β€œ00FNCOFF” to cancel the current function.
6 5
END
No response for
1 second or longer
No response for
1 second or longer
Sending command again
Number of trials
without response
Sending β€œ00vST”
Checking response to β€œ00vST”
[RS-232C control flowchart]
[Method of checking state of projector]
START
Check the following.
The projector is not supplied with AC power.β€’
β†’ Check that AC power cord is connected.
β†’ Turn on the power. (Turn on the circuit breaker or
main switch.)
Not connected with the projector.β€’
β†’ Check that the RS-232C cable is connected.
β†’ Check the RS-232C cable for electrical discontinuity.
The projector is in the state of being unable to send out β€’
a command.
β†’ Use command β€œ00vST” to check if the projector
operates normally.
Note: In the following conditions, the projector
does not respond even if it operates
normally.
β€’ Immediately after turning on the power
(for about 20 seconds to 2 minutes)
β€’ During switching signals (about 10
seconds)
β€’ In the process of the auto position
(about 10 seconds)
β€’ During locking the password


Product specificaties

Merk: Mitsubishi
Categorie: Beamer
Model: XL6600U
Gewicht: 9800 g
Stroomvoorziening: AC100 - 240V, 50 / 60Hz
Connectiviteitstechnologie: Bedraad
Typische contrastverhouding: 1000:1
Projector helderheid: 6000 ANSI lumens
Projectietechnologie: LCD
Projector native resolution: XGA (1024x768)
Geschikt voor schermmaten: 60 - 300 "
Frequentiebereik horizontaal: 15 - 100 kHz
Frequentiebereik verticaal: 50 - 120 Hz
Aantal USB 2.0-poorten: 1
VGA (D-Sub)poort(en): 1
Soort serieΓ«le aansluiting: RS-232
Audio-ingang (L, R): 1
PC audio ingang: Ja
Componentingang video (YPbPr/YCbCr): 1
S-Video ingang: 1
DVI-poort: Ja
Aantal Ethernet LAN (RJ-45)-poorten: 1
Levensduur van de lichtbron: 2000 uur
Type lichtbron: Lamp
Gemiddeld vermogen: 10 W
Formaat analoog signaal: NTSC, PAL, SECAM
RS-232 port: 1
Lampvermogen: 220 W
Audio (L,R) out: 1
Levensduur van de lichtbron (besparingsmodus): 4000 uur
Dot clock scanfrequentie: 162 MHz
Afmetingen (B x D x H): 443 x 434 x 207 mm
Afstandsbediening inbegrepen: Ja
Type product: Projector voor grote zalen

Heb je hulp nodig?

Als je hulp nodig hebt met Mitsubishi XL6600U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Beamer Mitsubishi

Handleiding Beamer

Nieuwste handleidingen voor Beamer