Milwaukee M18 Force Logic 2672-21S Handleiding

Milwaukee Zaagmachine M18 Force Logic 2672-21S

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 Force Logic 2672-21S (16 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16

Cat. No. / No de cat.

2672-20

M18™ FORCE LOGIC™ CABLE CUTTER

COUPE-CÂBLE M18™ FORCE LOGIC™

CORTACABLES M18™ FORCE LOGIC™

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to follow

all instructions listed below may result in electric shock,

re and/or serious injury. Save all warnings and in-

structions for future reference. The term "power tool"

in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Un-

modied plugs and matching outlets will reduce risk of

electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

• Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suit-

able for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces the

risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a power tool while you are tired or under the

inuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the o󰀨-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch

on invites accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jew-

elry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn

it on and o󰀨. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Pow-

er tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may a󰀨ect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations di󰀨erent

from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of re when used with

another battery pack.

• Use power tools only with specically designated

battery packs. Use of any other battery packs may

create a risk of injury and re.

• When battery pack is not in use, keep it away from oth-

er metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make

a connection from one terminal to another. Shorting

the battery terminals together may cause burns or a re.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact ac-

cidentally occurs, ush with water. If liquid con-

tacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or

modied. Damaged or modied batteries may exhibit

unpredictable behavior resulting in re, explosion or

risk of injury.

• Do not expose a battery pack or tool to re or ex-

cessive temperature. Exposure to re or temperature

above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specied in the instructions. Charging im-

properly or at temperatures outside the specied range

may damage the battery and increase the risk of re.

SERVICE

• Have your power tool serviced by a qualied repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

• Never service damaged battery packs. Service of

battery packs should only be performed by the manu-

facturer or authorized service providers.

SPECIFIC SAFETY RULES FOR

CABLE CUTTER

• Do not use tool without cutting jaws installed.

Fingers could be crushed.

• Blade is sharp. Keep hands away from all cutting edges

and moving parts. Laceration and amputation can occur.

• To reduce the risk of injury, wear safety goggles or

glasses with side shields when operating or servic-

ing the tool. Material may crack or shatter.

•

WARNING

To reduce the risk of arc ash,

electric shock and property

damage, work on deenergized lines when pos-

sible. Tool is not insulated. Should work on

energized lines be required, ensure all proper

precautions, including those contained in NFPA

70E, have been taken rst.

• Chemical Burn Hazard. Keep coin cell battery away

from children.

• For best results, use only with energy absorbing

lanyards. Ropes, straps or chains may break and

cause failure. Do not use with lanyards at full ten-

sion.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every situation

that could result in a dangerous outcome. Do not use this

tool if you do not understand these operating instructions

or you feel the work is beyond your capability; contact

Milwaukee Tool or a trained professional for additional

information or training.

• Maintain labels and nameplates. These carry im-

portant information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

•

WARNING

Some dust created by power sanding,

sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to lter

out microscopic particles.

SYMBOLOGY

Volts

Direct Current

WARNING

To reduce the risk of arc

ash, electric shock and

property damage, work on deenergized

lines when possible. Tool is not insulated.

Should work on energized lines be

required, ensure all proper precautions,

including those contained in NFPA 70E,

have been taken rst.

WARNING

Keep hands away from all

cutting edges and moving

parts. Blade is sharp. Laceration and

amputation can occur.

To reduce the risk of injury, wear safety

goggles or glasses with side shields when

operating or servicing the tool.

Read operator's manual.

C US

UL Listing for Canada and U.S.

SPECIFICATIONS

Cat. No. 2672-20 .....................................................

Volts ...................................................................18 DC

Battery Type ..................................................... M18™

Charger Type ................................................... M18™

Module/FCC ID ........BGM220S2/QOQ-BGM220S2

Recommended Ambient

Operating Temperature .................... 0°F to 122°F

Jaw Type ..........................................477 ACSR Jaws

(Cat. No. 49-16-2773)

Maximum Capacity ...... ACSR: 477 MCM Hen ACSR

Guy Wire: 3/8" Non-EHS

Rebar: 3/8"

Ground Rod: 3/8"

Replacement Blades .................. Cat. No. 48-44-0412

Jaw Type ..................................... 750 MCM Cu Jaws

(Cat. No. 49-16-2772)

Maximum Capacity ..............Copper Cable: 750 mcm

Aluminum Cable: 1000 mcm*

Replacement Blades .................. Cat. No. 48-44-0411

* 750 MCM Cu Jaws will cut any aluminum cable with a

diameter less than 1.225"

Jaw Type ............................1/2" EHS Guy Wire Jaws

(Cat. No. 49-16-2777)

Maximum Capacity EHS Guy Wire: 1/2" (19 strand)**

Non-EHS Guy Wire: 1/2" (7 & 19 strand)**

ACSR: 4/0 AWG

Rebar: 3/8"

Ground Rod: 3/8"

Replacement Blades .................Cat. No. 48-44-2777

** May require two cutting cycles to complete cut on

1/2" wire

Jaw Type ........................... Fine Stranded Wire Jaws

(Cat. No. 49-16-2778)

Maximum Capacity ..................... Fine Stranded Wire:

1/0 AWG - 777.7 AWG***

Replacement Blades .................Cat. No. 48-44-2778

*** Jaws should only be used on the following wire

classes: M, K, I/DLO

Product specificaties

Merk:	Milwaukee
Categorie:	Zaagmachine
Model:	M18 Force Logic 2672-21S

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 Force Logic 2672-21S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Milwaukee

Milwaukee M18 BJS Handleiding

10 April 2024

Milwaukee SCS 65 Q Handleiding

10 April 2024

Milwaukee M12 BS Handleiding

10 April 2024

Milwaukee M18 FMCS66 Handleiding

10 April 2024

Milwaukee M18 BSX Handleiding

10 April 2024

Milwaukee SSPE 1500 X Handleiding

19 Maart 2024

Milwaukee SSPE 1300 RX Handleiding

19 Maart 2024

Milwaukee BS 125 Handleiding

19 Maart 2024

Milwaukee SSD 1100 X Handleiding

18 Maart 2024

Milwaukee M18 BSX-402C Handleiding

14 Maart 2024

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Worx Nitro WX542.9 Handleiding

26 April 2024

Fieldmann FZP 25410-B Handleiding

15 April 2024

Rona Standard Plus-C Handleiding

10 April 2024

Rona Profi-C Handleiding

10 April 2024

Bavaria By Einhell BFS 800E Handleiding

9 April 2024

Bavaria By Einhell BPS 520 E Handleiding

9 April 2024

Bavaria By Einhell BHS 75 Handleiding

9 April 2024

Bavaria By Einhell BTS 400 Handleiding

9 April 2024

Bavaria By Einhell BHS 55 Handleiding

9 April 2024

Baumr-AG PC3 Handleiding

8 April 2024