Milwaukee M18 2646-21CT Handleiding

Milwaukee Niet gecategoriseerd M18 2646-21CT

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 2646-21CT (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

Cat. No. / No de cat.

2646-20

M18™ CORDLESS GREASE GUN

PISTOLET GRAISSEUR SANS FIL M18™

PISTOLA DE GRASA INALÁMBRICA M18™

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT Aﬁ n de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT Aﬁ n de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and speciﬁ ca-

tions provided with this power tool. Failure to

follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury. Save all

warnings and instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operat-

ing a power tool. Distractions can cause you to lose

control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces

the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂ uence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the oﬀ -position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your ﬁ nger on

the switch or energizing power tools that have the

switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which

it was designed.

• Do not use the power tool if the switch does not

turn it on and oﬀ . Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

• Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aﬀ ect the power tool’s operation. If damaged,

have the power tool repaired before use. Many

accidents are caused by poorly maintained power

tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations diﬀ erent from those intended could

result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger speciﬁ ed by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of ﬁ re when used

with another battery pack.

• Use power tools only with speciﬁ cally designated

battery packs. Use of any other battery packs may

create a risk of injury and ﬁ re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal

to another. Shorting the battery terminals together

may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact ac-

cidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

• Do not use a battery pack or tool that is dam-

aged or modiﬁ ed. Damaged or modiﬁ ed batteries

may exhibit unpredictable behavior resulting in ﬁ re,

explosion or risk of injury.

• Do not expose a battery pack or tool to ﬁ re or

excessive temperature. Exposure to ﬁ re or tem-

perature above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range speciﬁ ed in the instructions. Charging im-

properly or at temperatures outside the speciﬁ ed range

may damage the battery and increase the risk of ﬁ re.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

• Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SPECIFIC SAFETY RULES FOR

GREASE GUN

• High pressure can cause some tool parts or hose

assembly to rupture, posing a risk of injection

injury and/or amputation. Inspect tool and hose

assembly for damage or wear before each use. Do

not use if damaged or worn.

• Do not operate without proper safety apparel,

including eye protection marked to comply with

ANSI Z87.1, and gloves.

• Hold Hose Assembly by spring strain relief to

avoid kinking the hose.

• Grease and lubricants may be ﬂ ammable. Do not

expose to ﬂ ame or heat source. Follow all warnings

and instructions from grease and lubricant manu-

facturer.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every

situation that could result in a dangerous outcome.

Do not use this tool if you do not understand these

operating instructions or you feel the work is beyond

your capability; contact Milwaukee Tool or a trained

professional for additional information or training.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

•

WARNING

Some dust created by power sanding,

sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

ﬁ lter out microscopic particles.

SYMBOLOGY

Volts

Direct Current

psi Pounds per Square Inch

Read Operator's Manual

CUS UL Listing for Canada and U.S.

FUNCTIONAL DESCRIPTION

1. Handle

2. Trigger

3. Trigger lock-on/oﬀ

4. LED ON/OFF

5. LED

6. Hose Assembly

7. Strain relief

8. Strap eyelets

9. Bolt

10. Bleed valve

11.Hose clamp

12.Barrel

13.Rod handle

14.Loader coupler

15.Counter dial

16.Speed control

CAUTION

To avoid contamination in the grease

gun, Always make sure the barrel

(inside and outside) and surfaces contacting the

barrel are clean of dirt, dust and debris. This

debris can be pulled into the grease gun and clog

the valve.

Grease Cartridge Loading

1. Remove the battery pack.

2. Pull back the rod, and push it sideways into the

retaining slot. Ensure the rod is securely seated

in the slot or it may spring back.

3. Unscrew and remove

the barrel.

4. Remove the cap from

the cartridge.

5. Insert the cartridge,

open end first, into

the barrel.

6. Remove the seal from

the cartridge.

7. Screw the barrel into

the grease gun.

8. Release the rod from

the retaining slot and press it completely into the

barrel.

9. Prime the grease gun according to "Priming the

Grease Gun"

Bulk Grease Loading

Bulk grease can be loaded 2 ways, using the barrel

for suction loading, or using a pump to load grease

through a coupler.

Suction Loading

1. Remove the battery pack.

2. Unscrew and remove the barrel.

3. Insert the open end of the barrel below the surface

of the bulk grease.

4. Pull back the rod, and push it sideways into the

retaining slot.

5. Remove the barrel from the bulk grease.

6. Wipe excess grease from the outside of the barrel

and screw it into the grease gun.

7. Release the rod from the retaining slot and press

it completely into the barrel.

8. Prime the grease gun according to "Priming the

Grease Gun"

WARNING

To reduce the risk of injury, use

only low pressure loader ﬁ ttings.

Excessive pressure can be caused by high pres-

sure loader ﬁ ttings.

Pump Loading

1. Remove the battery pack.

2. Pull back the rod and turn the rod handle to lock

into the plunger. Release the rod/plunger. Do NOT

push the rod into the retaining slot.

3. Insert the loader ﬁ tting into the grease gun loader

coupler.

CAUTION

To avoid damage to the grease gun

and pump, the loader ﬁ tting MUST be

compatible with the coupler and rated for at least

10,000 psi (690 bar).

4. Operate the loader pump until the rod has been

pushed out of the barrel approximately 8".

5. Rotate the rod handle to release the plunger.

Press the rod completely into the barrel.

6. Prime the grease gun according to "Priming the

Grease Gun"

Priming the Grease Gun

1. Insert the battery pack

2. Push the priming valve until all air has escaped.

3. Hold the hose assembly by the spring strain relief

and point away from your body.

4. Pull the trigger for 10-20 seconds.

5. If grease doesn't not appear, repeat from step 2.

NOTE: This tool has been tested to factory stan-

dards, which results in a small amount of grease be-

ing left in the pump body, hose and coupler assembly.

It is recommended that you purge this tool with the

brand of grease you will be using before actual use.

LED

To turn the LED on or oﬀ , press the LED button or

pull the trigger. The LED will go oﬀ automatically 10

minutes after last use.

Counter Dial

The counter dial can be set to limit the amount of

grease dispensed. Set the dial to ON to dispense

grease as long as the trigger is pulled. Set the dial

to "1" through "50" to dispense grease for a speciﬁ c

number of piston strokes. The counter is reset NOTE:

each time the trigger is pulled. If the counter is set

for 10, but the trigger is only pulled for 6 strokes, the

next time the trigger is pulled it will start over.

Speed Control

Push the speed control switch to display "1" for low

ﬂ ow rate, high pressure. Push the speed control

switch to display "2" for high ﬂ ow rate, low pressure.

Troubleshooting

Unable to pull back

rod

Press the bleeder to

release pressure

Unable to push rod

forward

Rotate rod 90° to

disengage it from plunger

No grease when

trigger is pulled

Barrel is empty, add

grease

Air pockets in the barrel,

prime the grease gun

Contamination in grease

barrel, see "Clearing

Contamination"

Grease gun stops

pumping after one/

several pump strokes

Conﬁ rm that Counter dial

is set to "ON" position

Clearing Contamination

If the motor runs when the trigger is pulled, but there

is no pumping sound and grease is not dispensed,

there may be contamination in the grease gun. Al-

ways make sure the barrel (inside and outside) and

surfaces contacting the barrel are clean of dirt, dust

and debris. This debris can be pulled into the grease

gun and clog the valve.

To clear the contamination:

1. Check to be sure the tool is properly primed and

that there is suﬃ cient grease in the barrel.

If the problem persists...

2. Remove the hose assembly.

3. Pull and hold the trigger for up to 45 seconds. If

grease begins to pump out of the tool the debris

has been cleared. Reattach the hose assembly

and begin using the tool.

If the problem persists...

SPECIFICATIONS

Cat. No. ..................................................... 2646-20

Volts.............................................................. 18 DC

Battery Type .................................................M18™

Charger Type................................................ M18™

Max. Operating Pressure............... 1 ..... 10,000 psi

(690 bar)

2 ........5000 psi

(345 bar)

Flow Rate ...................................... 1 .....3.5 oz/min

2 ...... 10 oz/min

Barrel Capacity .......................................16 oz Bulk

14.5 oz Cartridge

Hose Rating ............................ 10,000 psi (690 bar)

Recommended Ambient

Operating Temperature ......................0°F to 125°F

ASSEMBLY

WARNING

Recharge only with the charger

speciﬁ ed for the battery. For spe-

ciﬁ c charging instructions, read the operator’s

manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

WARNING

Always lock the trigger or remove

the battery pack any time the tool

is not in use.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

WARNING

Only use accessories speciﬁ cally

recommended for this tool. Others

may be hazardous.

Installing the Clear Barrel

(Accessory Cat. No. 49-16-2646)

A clear grease barrel is oﬀ ered to replace the pro-

vided steel barrel.

1. To install the clear barrel, unscrew and remove the

steel grease barrel from the tool.

2. Unscrew the cap with rod from the back of the

steel barrel.

3. Remove the spacer screw with a phillips screw-

driver, and remove the plastic spacer by squeezing

the two retention tabs and pulling away from the

tool.

4. Screw the back cap with rod onto the clear barrel.

5. Screw the clear barrel into tool.

OPERATION

WARNING

Always remove battery pack before

changing or removing accesso-

ries. Only use accessories speciﬁ cally recom-

mended for this tool. Others may be hazardous.

To reduce the risk of injury, always wear proper

eye protection marked to comply with ANSI Z87.1.

Fuel Gauge

To determine the amount of charge left in the bat-

tery, pull the trigger. The Fuel Gauge will light up for

2-3 seconds.

To signal the end of charge, 1 light on the fuel gauge

will ﬂ ash for 2-3 seconds.

Installing a Fitting/Coupler

Screw the appropriate coupler to the end of the hose

assembly. Use only accessories rated for at least

10,000 psi (690 bar).

4. Remove the bolt from below the hose assembly.

5. Pull trigger for 15 seconds to clear the contamina-

tion.

6. If a spring or ball are

expelled, wipe away any

contamination and re-

insert, as shown.

7. Reattach the bolt and

tighten securely.

8. Pull trigger for 30 sec-

onds.

9. Reattach the hose as-

sembly and begin using

the tool.

MAINTENANCE

WARNING

To reduce the risk of injury, always

unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disassemble

the tool, battery pack or charger. Contact a

MILWAUKEE service facility for ALL repairs.

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

Inspect your tool for issues such as undue noise,

misalignment or binding of moving parts, breakage of

parts, or any other condition that may aﬀ ect the tool

operation. Return the tool, battery pack, and charger

to a MILWAUKEE service facility for repair. After six

months to one year, depending on use, return the

tool, battery pack and charger to a MILWAUKEE

service facility for inspection.

If the tool does not start or operate at full power with

a fully charged battery pack, clean the contacts on

the battery pack. If the tool still does not work prop-

erly, return the tool, charger and battery pack, to a

MILWAUKEE service facility for repairs.

WARNING

To reduce the risk of personal in-

jury and damage, never immerse

your tool, battery pack or charger in liquid or

allow a liquid to ﬂ ow inside them.

Cleaning

Clean dust and debris from any vents. Keep tool

clean, dry and free of oil or grease. Use only mild

soap and a damp cloth to clean, since certain clean-

ing agents and solvents are harmful to plastics and

other insulated parts. Some of these include gasoline,

turpentine, lacquer thinner, paint thinner, chlorinated

cleaning solvents, ammonia and household deter-

gents containing ammonia. Never use ﬂ ammable or

combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and charger

to the nearest authorized service center.

ACCESSORIES

WARNING

Use only recommended accesso-

ries. Others may be hazardous.

For a complete listing of accessories, go online to

www.milwaukeetool.com or contact a distributor.

Product specificaties

Merk:	Milwaukee
Categorie:	Niet gecategoriseerd
Model:	M18 2646-21CT

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 2646-21CT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Milwaukee

Milwaukee L4 RLEPB Handleiding

19 November 2024

Milwaukee M18 Fuel Angler 2873B-22 Handleiding

16 November 2024

Milwaukee M18 Radius ONE-KEY 2150-20 Handleiding

25 Juni 2024

Milwaukee MXF041 Handleiding

23 Juni 2024

Milwaukee ROLL-ON 3300R Handleiding

23 Juni 2024

Milwaukee MXF NRG Handleiding

10 Juni 2024

Milwaukee TRB 1 Handleiding

10 Juni 2024

Milwaukee M12 IR-201B Handleiding

10 Juni 2024

Milwaukee L4 PPS Handleiding

10 Juni 2024

Milwaukee M12 FPTR Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux STA9 Handleiding

23 November 2024

Electrolux UMP3 Handleiding

23 November 2024

Electrolux ZS70GL Handleiding

23 November 2024

Bosch HEZ8TK36UC Handleiding

23 November 2024

Bosch HEZ8ZZ36UC Handleiding

23 November 2024

Bosch HDZIT301 Handleiding

23 November 2024

Bosch HEZBS301 Handleiding

23 November 2024

LG LX-330 Handleiding

23 November 2024

Stamos S-PLASMA 60U Handleiding

23 November 2024

Bosch KSZ2AVU00 Handleiding

22 November 2024