Milwaukee M18 2631-21 Handleiding
Milwaukee
Zaagmachine
M18 2631-21
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 2631-21 (24 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/24
Cat. No. / No de cat.
2631-20
M18TM BRUSHLESS 7-1/4" CIRCULAR SAW
BRUSHLESS SCIE CIRCULAIRE DE 184 mm (7-1/4") M18 TM
SIN CEPILLO SIERRA CIRCULAR DE 184 mm (7-1/4") DE M18 TM
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn
it on and o. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Pow-
er tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may aect
the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Us
e the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, ush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
3
• Do not use a battery pack or tool that is damaged or
modied. Damaged or modied batteries may exhibit
unpredictable behavior resulting in re, explosion or
risk of injury.
• Do not expose a battery pack or tool to re or exces-
sive temperature. Exposure to re or temperature
above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging im-
properly or at temperatures outside the specied range
may damage the battery and increase the risk of re.
SERVICE
•
Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
CIRCULAR SAW
Cutting procedures
•
DANGER
Keep hands away from cutting area
and the blade. Keep your second
hand on auxiliary handle, or motor housing. If both
hands are holding the saw, they cannot be cut by the
blade.
• Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
• Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
• Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimize body exposure, blade binding,
or loss of control.
• Hold the power tool by insulated gripping sur-
faces when performing an operation where the
cutting tool may contact hidden wiring. Contact
with a “live” wire will also make exposed metal parts
of the power tool “live” and could give the operator
an electric shock.
• When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
• Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run o-center, causing loss of control.
• Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Further safety instructions for all saws
Kickback causes and related warnings
- Kickback is a sudden reaction to a pinched, jammed,
or misaligned saw blade, causing an uncontrolled saw
to lift up and out of the workpiece toward the operator;
- When the blade is pinched or jammed tightly by the
kerf closing down, the blade stalls and the motor reac-
tion drives the unit rapidly back toward the operator;
- If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into
the top surface of the wood causing the blade to climb
out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below:
• Maintain a rm grip with both hands on the saw and
position your arms to resist kickback forces. Posi-
tion your body to either side of the blade, but not
in line with the blade. Kickback could cause the saw
to jump backwards, but kickback forces can be con-
trolled by the operator, if proper precautions are taken.
• When blade is binding, or when interrupting a
cut for any reason, release the trigger and hold
the saw motionless in the material until the
blade comes to a complete stop. Never attempt
to remove the saw from the work or pull the saw
backward while the blade is in motion or kickback
may occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
• When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade binds,
it may walk up or kickback from the workpiece as the
saw is restarted.
• Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed
under the panel on both sides, near the line of cut
and near the edge of the panel.
• Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
• Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If
blade adjustment shifts while cutting, it may cause
binding and kickback.
• Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
Lower guard function
• Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does
not move freely and close instantly. Never clamp
or tie the lower guard into the open position. If
saw is accidentally dropped, the lower guard may be
bent. Raise the lower guard with the retracting handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
• Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
• Lower guard may be retracted manually only for
special cuts such as “plunge cuts” and “com-
pound cuts.” Raise lower guard by retracting handle
and as soon as blade enters the material, the lower
guard must be released. For all other sawing, the
lower guard should operate automatically.
• Alw
ays observe that the lower guard is covering
the blade before placing saw down on bench or
oor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to
stop after switch is released.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Zaagmachine |
| Model: | M18 2631-21 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M18 2631-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaagmachine Milwaukee
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
19 Maart 2024
19 Maart 2024
19 Maart 2024
18 Maart 2024
14 Maart 2024
Handleiding Zaagmachine
- Zaagmachine Bosch
- Zaagmachine AEG
- Zaagmachine DeWalt
- Zaagmachine Ford
- Zaagmachine Al-ko
- Zaagmachine Atika
- Zaagmachine BabyGO
- Zaagmachine Batavia
- Zaagmachine Bavaria
- Zaagmachine Bebe Confort
- Zaagmachine BGU
- Zaagmachine Blucave
- Zaagmachine Bort
- Zaagmachine Brennenstuhl
- Zaagmachine Bruder Mannesmann
- Zaagmachine Budget
- Zaagmachine Defort
- Zaagmachine Dolmar
- Zaagmachine Dremel
- Zaagmachine Duro
- Zaagmachine Echo
- Zaagmachine Einhell
- Zaagmachine Elektra Beckum
- Zaagmachine Elu
- Zaagmachine Ergofix
- Zaagmachine Exakt
- Zaagmachine Fein
- Zaagmachine Felisatti
- Zaagmachine Ferm
- Zaagmachine Ferrex
- Zaagmachine Festool
- Zaagmachine Flex
- Zaagmachine Florabest
- Zaagmachine FOM
- Zaagmachine Fuxtec
- Zaagmachine Gamma
- Zaagmachine Gardena
- Zaagmachine Gardenline
- Zaagmachine Germania
- Zaagmachine Global
- Zaagmachine Greenworks
- Zaagmachine Grizzly
- Zaagmachine Gude
- Zaagmachine Gude Pro
- Zaagmachine Hammer
- Zaagmachine Hikoki
- Zaagmachine Hitachi
- Zaagmachine Holzmann
- Zaagmachine Homelite
- Zaagmachine Husqvarna
- Zaagmachine Huvema
- Zaagmachine Hyundai
- Zaagmachine Ideal
- Zaagmachine Kompernass
- Zaagmachine Kress
- Zaagmachine Lux Tools
- Zaagmachine Luxor
- Zaagmachine Maestro
- Zaagmachine Makita
- Zaagmachine Maktec
- Zaagmachine Matrix
- Zaagmachine Max
- Zaagmachine Maxx
- Zaagmachine McCulloch
- Zaagmachine Metabo
- Zaagmachine Parkside
- Zaagmachine Pattfield
- Zaagmachine Plantiflor
- Zaagmachine Powerfix
- Zaagmachine Powerplus
- Zaagmachine Remington
- Zaagmachine Robust
- Zaagmachine Ryobi
- Zaagmachine Scheppach
- Zaagmachine Shindaiwa
- Zaagmachine Silverline
- Zaagmachine Skil
- Zaagmachine Stanley
- Zaagmachine Sterwins
- Zaagmachine Stiga
- Zaagmachine Stihl
- Zaagmachine Tanaka
- Zaagmachine Texas
- Zaagmachine Toledo
- Zaagmachine Toolcraft
- Zaagmachine Topcraft
- Zaagmachine Trotec
- Zaagmachine Troy-Bilt
- Zaagmachine Varo
- Zaagmachine Vonroc
- Zaagmachine Westfalia
- Zaagmachine Workzone
- Zaagmachine Worx
- Zaagmachine Zipper
- Zaagmachine Ozito
- Zaagmachine Black And Decker
- Zaagmachine Cocraft
- Zaagmachine Draper
- Zaagmachine Meec Tools
- Zaagmachine Lionelo
- Zaagmachine Clarke
- Zaagmachine Genesis
- Zaagmachine Hilti
- Zaagmachine Cobra
- Zaagmachine Hobart
- Zaagmachine ACG
- Zaagmachine Cotech
- Zaagmachine Power Craft
- Zaagmachine Tacklife
- Zaagmachine Truper
- Zaagmachine Fieldmann
- Zaagmachine Mafell
- Zaagmachine Proxxon
- Zaagmachine Biltema
- Zaagmachine Porter-Cable
- Zaagmachine Sun Joe
- Zaagmachine Yard Force
- Zaagmachine Challenge
- Zaagmachine EGO
- Zaagmachine Hurricane
- Zaagmachine Sovereign
- Zaagmachine Spear & Jackson
- Zaagmachine Dedra
- Zaagmachine Graphite
- Zaagmachine Narex
- Zaagmachine RIDGID
- Zaagmachine Tryton
- Zaagmachine Herkules
- Zaagmachine Powerworks
- Zaagmachine Sthor
- Zaagmachine Craftsman
- Zaagmachine Rikon
- Zaagmachine Verto
- Zaagmachine Erbauer
- Zaagmachine Snow Joe
- Zaagmachine Chicago Pneumatic
- Zaagmachine Alpha Tools
- Zaagmachine Hazet
- Zaagmachine Yato
- Zaagmachine Jonsered
- Zaagmachine Qualcast
- Zaagmachine Avantco
- Zaagmachine Masport
- Zaagmachine Morrison
- Zaagmachine Baumr-AG
- Zaagmachine Martha Stewart
- Zaagmachine IKRA
- Zaagmachine MTM
- Zaagmachine Meister Craft
- Zaagmachine Łucznik
- Zaagmachine King Craft
- Zaagmachine Toolson
- Zaagmachine Wolfcraft
- Zaagmachine Kreg
- Zaagmachine Vulcan
- Zaagmachine Challenge Xtreme
- Zaagmachine Pro-Cut
- Zaagmachine Power Smart
- Zaagmachine Backyard Pro Butcher Series
- Zaagmachine EFA
- Zaagmachine Einhell Bavaria
- Zaagmachine McKenzie
- Zaagmachine Proviel
- Zaagmachine Ultranatura
- Zaagmachine FIXIT
- Zaagmachine Ergotools Pattfield
- Zaagmachine MyTool
- Zaagmachine Bavaria By Einhell
- Zaagmachine Donau Elektronik
- Zaagmachine Rona
Nieuwste handleidingen voor Zaagmachine
26 April 2024
15 April 2024
10 April 2024
10 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
8 April 2024