Milwaukee M18 2123-20 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M18 2123-20 (11 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/11
Cat. No. / No de cat.
2123-20
M18â„¢ UTILITY REMOTE CONTROL SEARCH LIGHT
PROJECTEUR UTILITAIRE TÉLÉCOMMANDÉ M18™
PROYECTOR UTILITARIO CON CONTROL REMOTO M18â„¢
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and speciîš¿ca-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, îš¿re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiîš¿ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o󰀨-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your îš¿nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and o󰀨. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may a󰀨ect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations di󰀨erent from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of îš¿re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and îš¿re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins
4
ASSEMBLY
WARNING
Recharge only with the charger
speciîš¿ed for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, lift the battery door latches
and open the battery door. Push in the battery re-
lease buttons and pull the battery pack away from
the tool. Close the battery door and relatch the door
latches securely.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, lift the battery door latches
and open the battery door. Slide the pack into the
body of the tool. Make sure it latches securely into
place. Close the battery door and relatch the door
latches securely.
WARNING
Only use accessories speciîš¿cally
recommended for this tool. Others
may be hazardous.
Installing the Base
WARNING
The base should be installed ac-
cording to the vehicle manufac-
turer's speciîš¿cations by a qualiîš¿ed technician.
Drilling holes in certain structural areas, or
wiring incorrectly, could compromise the safety
of the vehicle.
To mount the permanent base:
1. Place the base on the desired location. Make sure
it is on a clean, dry surface.
2. Mount the base to the location using four 1/4"
screws.
3. Connect to the vehicle’s wiring per the manufac-
turer’s wiring schematic.
WARNING
Do not use magnet for horizontal
overhead mounting.
To mount the portable base:
Select the best location on your vehicle for the mag-
netic mount. Make sure the metal area under the
magnetic base is at and clean to ensure a strong
bond. WARNING! Excessive force will break the
magnet free. The light should be removed from a
vehicle's exterior while traveling and in strong wind
conditions.
Attaching/Removing the Light
FUNCTIONAL DESCRIPTION
10. Mounting
accessories
11. Power leads
12. Remote light
power button
13. Remote on/o󰀨
switch
14. Remote joystick
15. Remote mode
button
16. Instensity button
17. Lanyard (not shown)
18. Remote dash mount
4
5
8
2
1
6
3
9
10
11
1. Light head
2. ONE-KEYâ„¢
indicator
3. Mode button
4. Home button
5. Power button
6. Portable base
7. Battery
compartment
latches
8. Battery door
9. 12V DC
Permanent
base
12
13
14
15
16
17
18
7
2


Product specificaties

Merk: Milwaukee
Categorie: Afstandsbediening
Model: M18 2123-20

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee M18 2123-20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Milwaukee

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening