Milwaukee M12 Fuel HATCHET 2527-21 Handleiding
Milwaukee
Zaagmachine
M12 Fuel HATCHET 2527-21
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee M12 Fuel HATCHET 2527-21 (21 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/21
Cat. No. / No de cat.
2527-20
M12 FUEL™ HATCHET™ 6" PRUNING SAW
SCIE D'ÉLAGAGE DE 152 (6") HATCHET™ DE M12 FUEL™mm
SIERRA PODADORA DE 152 mm (6") HATCHET™ DE M12 FUEL™
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
•
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the o-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a ro-
tating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn
it on and o. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Pow-
er tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may aect
the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
dierent from those intended could result in a hazardous
situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, ush with water. If liquid contacts
eyes, additionally seek medical help. Liqui
ejected from the battery may cause irritation or burns
4
• Store pruning saw when not in use. Pruning saw
should be stored in a dry and high or locked area out
of the reach of children. When storing pruning saw
place the cover on the bar and chain.
• Battery operated units do not have to be plugged
into an electrical outlet; therefore, they are always
in operating condition. Be aware of possible haz-
ards even when unit is not operating.
• Save these instructions. Refer to them frequently
and use them to instruct others who may use this
product. If you loan someone this product, loan them
these instructions also.
• After each use, clean the machine with a soft dry
cloth. Remove any chips, dirt and debris in the
battery bay.
• Follow the manufacturer’s sharpening and main-
tenance instructions for the saw chain. Decreas-
ing the depth gauge height can lead to increased
kickback.
• Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SPECIFICATIONS
Cat. No. 2527-20 .....................................................
Volts 12 DC..............................................................
Battery Type .................................................M12™
Charger Type M12™................................................
RPM ................................................................2,650
Chain Speed ............................................984 ft/min
Bar Length ........................................................... 6"
Cutting Capacity ............................................... 5.5"
Chain Oil Tank Capacity ................................1.7 oz
Replacement Bar .................................. 49-16-2733
Chain Gauge ................................................ 0.043"
Replacement Chain .............................. 49-16-2732
Chain Type ........................................ Low kickback
Chain Pitch .....................................3/8" Low prole
Chain Teeth .........................................................28
Recommended Ambient
Operating Temperature ......................0°F to 125°F
• Dress Properly - Wear snug tting clothing. Always
wear heavy, long pants, long sleeves, overalls, jeans
or chaps made of cut resistant material or ones that
contain cut resistant inserts. Wear non-slip safety
footwear. Wear non-slip heavy duty gloves to improve
your grip and to protect your hands. Do not wear
jewelry, short pants, sandals, or go barefoot. Do not
wear loose tting clothing, which could be drawn into
the motor or catch the chain or underbrush. Secure
hair so it is above shoulder level.
• Heavy protective clothing may increase operator
fatigue, which could lead to heat stroke. During
weather that is hot and humid, heavy work should be
scheduled for early morning or late afternoon hours
when temperatures are cooler.
• Always wear proper eye protection with side
shields, marked to comply with ANSI Z87.1 when
operating the pruning saw.
• Always be aware of what you are doing when
using the pruning saw. Use common sense. Do
not operate the pruning saw when you are tired, ill, or
under the inuence of alcohol, drugs, or medication.
• Keep all parts of your body away from the saw
chain when the unit is running.
• Never let anyone use your pruning saw who has
not received adequate instructions in its proper
use. This applies to rentals as well as privately owned
saws.
• Before you start the unit, make sure the saw chain
is not contacting any object.
• Stop the pruning saw before setting it down.
• Maintain the unit with care. Keep the cutting edge
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating
and changing accessories.
• Maintain a rm grip on the recommended grasp-
ing surfaces. If an operation cannot be performed
safely with two hands on the saw, USE EXTREME
CAUTION.
• During operations where it is necessary to use
one hand, such as to steady or control the work-
piece/branch, guide workpiece away from you, or
provide better visibility to the work area:
• Keep free hand clear of the chain and out of the
cutting path.
• Maintain a rm grip on the branch being cut to avoid
"skating" or "bouncing" of the saw.
• Never cut above shoulder height.
• Do not cross arms or overreach.
• Always cut away from yourself.
• -Avoid excess exing or tension on the branch be
ing cut.
• Do not operate a pruning saw that is damaged, im-
properly adjusted, or not completely and securely
assembled. Chain should slow to a stop when the
switch trigger is released. If the chain continues to
turn after the switch trigger has been released, have
the unit serviced by an authorized service center.
• Do not force the pruning saw. The job can be
performed better and safer at the rate for which it
was intended.
• Always use the right product for your application.
The pruning saw should be used for cutting wood only.
Never use the pruning saw to cut plastic, masonry or
non-wood building materials.
• Use extreme caution when cutting thin branches,
vines or small underbrush. The slender material
may catch the saw chain and be whipped toward you
or pull you o balance. We recommend using hedge
trimmers or brush cutters for these operations.
SYMBOLOGY
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Zaagmachine |
| Model: | M12 Fuel HATCHET 2527-21 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee M12 Fuel HATCHET 2527-21 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaagmachine Milwaukee
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
19 Maart 2024
19 Maart 2024
19 Maart 2024
18 Maart 2024
14 Maart 2024
Handleiding Zaagmachine
- Zaagmachine Bosch
- Zaagmachine AEG
- Zaagmachine DeWalt
- Zaagmachine Ford
- Zaagmachine Al-ko
- Zaagmachine Atika
- Zaagmachine BabyGO
- Zaagmachine Batavia
- Zaagmachine Bavaria
- Zaagmachine Bebe Confort
- Zaagmachine BGU
- Zaagmachine Blucave
- Zaagmachine Bort
- Zaagmachine Brennenstuhl
- Zaagmachine Bruder Mannesmann
- Zaagmachine Budget
- Zaagmachine Defort
- Zaagmachine Dolmar
- Zaagmachine Dremel
- Zaagmachine Duro
- Zaagmachine Echo
- Zaagmachine Einhell
- Zaagmachine Elektra Beckum
- Zaagmachine Elu
- Zaagmachine Ergofix
- Zaagmachine Exakt
- Zaagmachine Fein
- Zaagmachine Felisatti
- Zaagmachine Ferm
- Zaagmachine Ferrex
- Zaagmachine Festool
- Zaagmachine Flex
- Zaagmachine Florabest
- Zaagmachine FOM
- Zaagmachine Fuxtec
- Zaagmachine Gamma
- Zaagmachine Gardena
- Zaagmachine Gardenline
- Zaagmachine Germania
- Zaagmachine Global
- Zaagmachine Greenworks
- Zaagmachine Grizzly
- Zaagmachine Gude
- Zaagmachine Gude Pro
- Zaagmachine Hammer
- Zaagmachine Hikoki
- Zaagmachine Hitachi
- Zaagmachine Holzmann
- Zaagmachine Homelite
- Zaagmachine Husqvarna
- Zaagmachine Huvema
- Zaagmachine Hyundai
- Zaagmachine Ideal
- Zaagmachine Kompernass
- Zaagmachine Kress
- Zaagmachine Lux Tools
- Zaagmachine Luxor
- Zaagmachine Maestro
- Zaagmachine Makita
- Zaagmachine Maktec
- Zaagmachine Matrix
- Zaagmachine Max
- Zaagmachine Maxx
- Zaagmachine McCulloch
- Zaagmachine Metabo
- Zaagmachine Parkside
- Zaagmachine Pattfield
- Zaagmachine Plantiflor
- Zaagmachine Powerfix
- Zaagmachine Powerplus
- Zaagmachine Remington
- Zaagmachine Robust
- Zaagmachine Ryobi
- Zaagmachine Scheppach
- Zaagmachine Shindaiwa
- Zaagmachine Silverline
- Zaagmachine Skil
- Zaagmachine Stanley
- Zaagmachine Sterwins
- Zaagmachine Stiga
- Zaagmachine Stihl
- Zaagmachine Tanaka
- Zaagmachine Texas
- Zaagmachine Toledo
- Zaagmachine Toolcraft
- Zaagmachine Topcraft
- Zaagmachine Trotec
- Zaagmachine Troy-Bilt
- Zaagmachine Varo
- Zaagmachine Vonroc
- Zaagmachine Westfalia
- Zaagmachine Workzone
- Zaagmachine Worx
- Zaagmachine Zipper
- Zaagmachine Ozito
- Zaagmachine Black And Decker
- Zaagmachine Cocraft
- Zaagmachine Draper
- Zaagmachine Meec Tools
- Zaagmachine Lionelo
- Zaagmachine Clarke
- Zaagmachine Genesis
- Zaagmachine Hilti
- Zaagmachine Cobra
- Zaagmachine Hobart
- Zaagmachine ACG
- Zaagmachine Cotech
- Zaagmachine Power Craft
- Zaagmachine Tacklife
- Zaagmachine Truper
- Zaagmachine Fieldmann
- Zaagmachine Mafell
- Zaagmachine Proxxon
- Zaagmachine Biltema
- Zaagmachine Porter-Cable
- Zaagmachine Sun Joe
- Zaagmachine Yard Force
- Zaagmachine Challenge
- Zaagmachine EGO
- Zaagmachine Hurricane
- Zaagmachine Sovereign
- Zaagmachine Spear & Jackson
- Zaagmachine Dedra
- Zaagmachine Graphite
- Zaagmachine Narex
- Zaagmachine RIDGID
- Zaagmachine Tryton
- Zaagmachine Herkules
- Zaagmachine Powerworks
- Zaagmachine Sthor
- Zaagmachine Craftsman
- Zaagmachine Rikon
- Zaagmachine Verto
- Zaagmachine Erbauer
- Zaagmachine Snow Joe
- Zaagmachine Chicago Pneumatic
- Zaagmachine Alpha Tools
- Zaagmachine Hazet
- Zaagmachine Yato
- Zaagmachine Jonsered
- Zaagmachine Qualcast
- Zaagmachine Avantco
- Zaagmachine Masport
- Zaagmachine Morrison
- Zaagmachine Baumr-AG
- Zaagmachine Martha Stewart
- Zaagmachine IKRA
- Zaagmachine MTM
- Zaagmachine Meister Craft
- Zaagmachine Łucznik
- Zaagmachine King Craft
- Zaagmachine Toolson
- Zaagmachine Wolfcraft
- Zaagmachine Kreg
- Zaagmachine Vulcan
- Zaagmachine Challenge Xtreme
- Zaagmachine Pro-Cut
- Zaagmachine Power Smart
- Zaagmachine Backyard Pro Butcher Series
- Zaagmachine EFA
- Zaagmachine Einhell Bavaria
- Zaagmachine McKenzie
- Zaagmachine Proviel
- Zaagmachine Ultranatura
- Zaagmachine FIXIT
- Zaagmachine Ergotools Pattfield
- Zaagmachine MyTool
- Zaagmachine Bavaria By Einhell
- Zaagmachine Donau Elektronik
- Zaagmachine Rona
Nieuwste handleidingen voor Zaagmachine
26 April 2024
15 April 2024
10 April 2024
10 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
8 April 2024