Milwaukee 6955-20 Handleiding

Milwaukee Zaagmachine 6955-20

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 6955-20 (6 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 71 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Cat. No. / No de cat.

6955-20

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

12" SLIDING DUAL BEVEL MITER SAW WITH DIGITAL FINE ADJUST

SCIE À ONGLETS COULISSANTE À DOUBLE BISEAU DE 305 mm

(12") AVEC FONCTION DE RÉGLAGE NUMÉRIQUE PRÉCIS

SIERRA INGLETEADORA DE BISEL DOBLE DESLIZABLE DE

305 mm (12") CON AJUSTE FINO DIGITAL

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to follow

all instructions listed below may result in electric shock,

re and/or serious injury. Save all warnings and in-

structions for future reference. The term "power tool"

in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

• Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suit-

able for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces the

risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a power tool while you are tired or under the

inuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

• Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non-skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the o󰀨-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch

on invites accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jew-

elry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn

it on and o󰀨. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Pow-

er tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may a󰀨ect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations di󰀨erent

from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

SERVICE

• Have your power tool serviced by a qualied repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SPECIFIC SAFETY RULES FOR

MITER SAW

• Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-o󰀨

wheels for cutting ferrous material such as bars,

rods, studs, etc. Abrasive dust causes moving parts

such as the lower guard to jam. Sparks from abrasive

cutting will burn the lower guard, the kerf insert and

other plastic parts.

• Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to

the saw blade, there is an increased risk of injury from

blade contact.

• The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or cut

“freehand” in any way. Unrestrained or moving work-

pieces could be thrown at high speeds, causing injury.

• Push the saw through the workpiece. Do not pull

the saw through the workpiece. To make a cut,

raise the saw head and pull it out over the work-

piece without cutting, start the motor, press the

saw head down and push the saw through the

workpiece. Cutting on the pull stroke is likely to cause

the saw blade to climb on top of the workpiece and vio-

lently throw the blade assembly towards the operator.

• Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your

left hand or vice versa is very dangerous.

• Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity of

the spinning saw blade to your hand may not be obvious

and you may be seriously injured.

• Inspect your workpiece before cutting. If the work-

piece is bowed or warped, clamp it with the outside

bowed face toward the fence. Always make certain

that there is no gap between the workpiece, fence

and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding

on the spinning saw blade while cutting. There should

be no nails or foreign objects in the workpiece.

• Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that con-

tact the revolving blade can be thrown with high speed.

• Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

• Ensure the miter saw is mounted or placed on a level,

rm work surface before use. A level and rm work sur-

face reduces the risk of the miter saw becoming unstable.

• Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool “ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

• Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top. Workpieces longer or

wider than the miter saw table can tip if not securely

supported. If the cut-o󰀨 piece or workpiece tips, it can

lift the lower guard or be thrown by the spinning blade.

• Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

• The cut-o󰀨 piece must not be jammed or pressed

by any means against the spinning saw blade. If

conned, i.e. using length stops, the cut-o󰀨 piece could

get wedged against the blade and thrown violently.

• Always use a clamp or a xture designed to properly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to “bite” and pull the work with your hand into the blade.

• Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

• If the workpiece or blade becomes jammed, turn the

mitre saw o󰀨. Wait for all moving parts to stop and

disconnect the plug from the power source and/

or remove the battery pack. Then work to free the

jammed material. Continued sawing with a jammed

workpiece could cause loss of control or damage to

the miter saw.

• After nishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-o󰀨 piece. Reaching with your hand

near the coasting blade is dangerous.

• Hold the handle rmly when making an incomplete

cut or when releasing the switch before the saw

head is completely in the down position. The brak-

ing action of the saw may cause the saw head to be

suddenly pulled downward, causing a risk of injury.

• Do not carry tool by workpiece supports. Supports

could bend or break, causing tool to drop. Only carry

tool by carrying handles.

•

WARNING

To reduce the risk of injury in ap-

plications that produce a consider-

able amount of dust, use an OSHA compliant dust

extraction solution in accordance with the solu-

tion’s operating instructions.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every situation

that could result in a dangerous outcome. Do not use this

tool if you do not understand these operating instructions

or you feel the work is beyond your capability; contact

Milwaukee Tool or a trained professional for additional

information or training.

• Maintain labels and nameplates. These carry im-

portant information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

•

WARNING

Some dust created by power sanding,

sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to lter

out microscopic particles.

SYMBOLOGY

Double Insulated

Volts

Alternating Current

Amps

No-Load Revolutions per Minute (RPM)

C US

UL Listing Mark for Canada and U.S.

Always keep hands away from the

path of the saw blade

No Hands Zone - Keep hands out of

the No Hands Zone at all times during

use. Contact with blade will result in

serious injury.

Product specificaties

Merk:	Milwaukee
Categorie:	Zaagmachine
Model:	6955-20

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 6955-20 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Zaagmachine Milwaukee

Milwaukee M18 FTCHS14 Handleiding

11 September 2024

Milwaukee MXF COSCG2 Handleiding

5 September 2024

Milwaukee MSUV280 Handleiding

10 Juni 2024

Milwaukee M18 BJS Handleiding

10 April 2024

Milwaukee SCS 65 Q Handleiding

10 April 2024

Milwaukee M12 BS Handleiding

10 April 2024

Milwaukee M18 FMCS66 Handleiding

10 April 2024

Milwaukee M18 BSX Handleiding

10 April 2024

Milwaukee SSPE 1500 X Handleiding

19 Maart 2024

Milwaukee SSPE 1300 RX Handleiding

19 Maart 2024

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Einhell BT-CS 700 E Handleiding

4 December 2024

Einhell BT-CS 500 Handleiding

4 December 2024

Einhell TKS 1500 ECO Plus Handleiding

4 December 2024

Einhell TKS 1500 ECO Handleiding

4 December 2024

Einhell MKS 1940 Handleiding

4 December 2024

Einhell WIS 400/230 Handleiding

4 December 2024

Einhell WIS 700/400 Handleiding

4 December 2024

Einhell WIS 600/400 Handleiding

4 December 2024

Einhell TE-TC 18/115 Li Handleiding

4 December 2024

Makita DJR187ZK Handleiding

2 December 2024