Milwaukee 48-44-0122 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 48-44-0122 (2 pagina's) in de categorie Schaar. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
00
0
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
®
REVISED BULLETIN DATE
CATALOG NO.
SERVICE PARTS LIST
MILWAUKEE TOOL CORPORATION 13135 W.
LISBON RD., BROOKFIELD, WI 53005
Drwg. 2
BULLETIN NO.
STARTING
SERIAL NO.
WIRING INSTRUCTION
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
18 GAUGE SHEAR HEAD ASSEMBLY
48-08-0500
Oct 19. 20
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 48-08-0500 Shear Head Assy. (Includes 2 thru 11) (1)
2 06-75-2115 10-24 x 1-1/4 Skt. Hd. Cap Screw (3)
3 43-76-0400 Shear Housing (1)
4 45-88-7310 Washer (1)
5 43-16-0100 Eccentric Assembly (1)
6 43-84-0460 Knurled Insert (3)
7 48-44-0170 Blade - Right Side (1)
8 42-40-0520 Bushing (2)
9 48-44-0150 Blade - Center (1)
10 48-44-0160 Blade - Left Side (1)
11 49-96-0070 5/32 Hex Allen Wrench (1)
FIG. LUBRICATION:
3,7,8 During assembly, use a dab of Type "E" Grease,
No. 49-08-4122 to lubricate flats, pivot hole and sides of
center blade (8), eccentric assembly (3) and bushing (7).
54-40-8220
*
Bottom view of
Shear Head
Assembly
Bushings
When servicing Shear Head Assembly No. 48-08-0500 pay close attention to the
placement of the Bushings. One is to be placed in the hole of the Center Blade
and is to be held in place with the front most screw on the Shear Housing. The
other bushing is to be located below the small concave notch of the Center Blade
and is to be secured with the middle screw on the Shear Housing. Prior to assem-
bly, it is recommended to use Type 'E' Grease, No. 49-08-4122 on the following
areas: Place a dab of grease in the pivot (bushing) hole and on the bushing notch
oftheCenterBlade.PlaceadabofgreaseontherearatsoftheCenterBlade.
Coat both bushings completely with grease.
Place a liberal amount of grease on the
entire Eccentric Assembly.
Illustration shown without tool attached
for clarity of spreader wrench
placement on shear head
Prior to using the
spreader wrench,
this screw must be
loosened two turns.
Remove this screw.
Insert the end of the
spreader wrench into the bottom
rear opening of shear head assembly
as shown. Twist the wrench in a clockwise
direction (allowing the rounded cam to roll and
spread the back of the shear housing). Spreader wrench
will rotate approximately 1/4 turn and stop at next flat after cam.
To remove spreader tool, turn counter-clockwise.
Front View
REMOVING SHEAR HEAD ASSEMBLY FROM TOOL
SERVICE TOOLS:
Spreader Wrench No. 61-30-0300
for 14 Gauge Shear Head 48-08-0505
used on Shear No. 2636-20
for 18 Gauge Shear Head 48-08-0507
used on Shear 2637-20
Spreader Wrench No. 61-30-0310
for 18 Gauge Shear Head 48-08-0500
used on Shears 2635-20 and 6852-20
Product specificaties
| Merk: | Milwaukee |
| Categorie: | Schaar |
| Model: | 48-44-0122 |
Heb je hulp nodig?
Als je hulp nodig hebt met Milwaukee 48-44-0122 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schaar Milwaukee
9 Juni 2023
23 Mei 2023
3 Mei 2023
15 April 2023
10 April 2023
5 April 2023
4 April 2023
16 Maart 2023
7 Maart 2023
26 Februari 2023
Handleiding Schaar
- Schaar DeWalt
- Schaar Fein
- Schaar Hikoki
- Schaar Hitachi
- Schaar Makita
- Schaar Parkside
- Schaar Rowenta
- Schaar Ryobi
- Schaar Silverline
- Schaar Trotec
- Schaar Black And Decker
- Schaar Sun Joe
- Schaar Hazet
Nieuwste handleidingen voor Schaar
26 Augustus 2024
17 Juli 2023
17 Juli 2023
20 Juni 2023
5 Juni 2023
29 Mei 2023
27 Mei 2023
21 Mei 2023
20 Mei 2023
13 Mei 2023