Milwaukee 48-22-8560 Handleiding

Milwaukee Niet gecategoriseerd 48-22-8560

Lees hieronder de 📖 handleiding in het Nederlandse voor Milwaukee 48-22-8560 (11 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 239 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/11

Cat. No. / No de cat.

48-22-8560

60" MOBILE WORK BENCH

BANC DE TRAVAIL MOBILE DE 1524 MM (60")

BANCO DE TRABAJO MÓVIL DE 1524 MM (60”)

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT Aﬁ n de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in serious in-

jury. Save all warnings and instructions for future

reference.

•Use the bench and accessories in accordance

with these instructions and in the manner in-

tended, taking into account the working conditions.

Use of the bench for operations different from those

intended could result in a hazardous situation.

•Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

•Fully assemble the bench according to the as-

sembly instructions. Do not leave off any pieces.

•Do not modify the bench in any way. Use only

specifically recommended accessories. Drilling

holes or modifying the bench will lower the load

capacity, which can cause the bench to collapse,

resulting in injury.

•Lock wheels when bench is not being moved.

Unlocked wheels can allow the bench to move

unexpectedly.

•Keep the bench on a level surface. Do not load,

unload, or park bench on an incline. The bench

may become unbalanced and tip, resulting in injury.

•Always balance the bench load to avoid tipping.

Unbalanced benches are more likely to tip when be-

ing moved or when using the bench work surfaces.

Evenly distribute the weight front to back and side

to side. To help prevent the bench from tipping,

load the product starting with the bottom drawers.

• Do not exceed the maximum product weight,

including contents. Do not exceed the maximum

weight for each drawer. Overloaded benches can

tip, collapse, or damage drawer slides.

• Do not open more than one drawer at a time.

Bench may tip, causing injury.

•Keep children and bystanders away while load-

ing, unloading, and moving bench. Distractions

can cause you to lose control.

•Only lift the bench according to the instructions

in this manual. Other methods may be dangerous,

resulting in injury.

• Only transport the bench when empty. Properly

secure when transporting.

• Do not mount the bench on a truck bed or any

other moving object.

• Lock all drawers before rolling the bench. The

drawers could come open and make the bench

unstable and tip.

• Only roll the bench short distances by using the

handle provided.

• Secure all items before rolling the bench. Loose

items could shift, causing the bench to become

unstable.

• Do not use drawers as steps. Do not stand

on the bench. Bench may tip, causing injury.

• Do not step on side shelf. Shelf may collapse or

break. Bench may tip, causing injury.

•Do not use bench in explosive atmospheres,

such as in the presence of ﬂ ammable liquids, gases

or dust. This equipment has internal arcing or spark-

ing parts. Bench should not be located in a recessed

area or below ﬂ oor level.

•Bench plugs must match the outlet. Never mod-

ify the plug in any way. Do not use any adapter

plugs with earth (grounded) chest/cabinet power

strips. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

•Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

•Maintain bench. Check for misalignment or binding

wheels, breakage or bending of drawer slides or

other parts and any other condition that may affect

the bench's operation. Do not use damaged bench.

•Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

•Have your bench serviced by a qualiﬁ ed repair

person using only identical replacement parts.

This will ensure that the safety of the bench is

maintained.

SYMBOLOGY

Warning

Read Operator's Manual

Electrical Shock Hazard

Do not open more than one drawer at a

time. Bench may tip, causing injury.

Lock wheels when bench is not

being moved. Unlocked wheels can

allow the bench to move

unexpectedly.

Do not use drawers as steps. Bench

may tip, causing injury.

FPO

Lock all drawers before moving the bench.

Do not step on side shelf. Shelf may

collapse or break. Bench may tip, causing

injury.

SPECIFICATIONS

Cat. No. ................................................ 48-22-8560

Two-Slide Drawer Capacity .........100 lbs. (45.4 kg)

Four-Slide Drawer Capacity ........200 lbs. (90.7 kg)

Peg Board Capacity.....................200 lbs. (90.7 kg)

Total Capacity ..........................2200 lbs. (997.9 kg)

FUNCTIONAL DESCRIPTION

1413

1110

1. Peg board

2. Tool hanger

3. Wood work

surface

4. Cabinet shelf

5. Cabinet shelf clip

6. Key

7. Swivel caster

with brake

8. Drawer divider

9. Lock

10. Rigid caster

11. Tool organizer

12. Drawer slide

13. Bumper

14. Storage shelf

15. Charger mounts

16. Cord storage

bracket

17. Side handle

18. Power strip

19. Locking thumb

screw

20. Peg board bracket

7 8 9

GROUNDING

WARNING

Improperly connecting the ground-

ing wire can result in the risk of

electric shock. Check with a qualiﬁ ed electrician

if you are in doubt as to whether the outlet is

properly grounded. Do not modify the plug pro-

vided with the bench. Never remove the ground-

ing prong from the plug. Do not use the bench if

the cord or plug is damaged. If damaged, have it

repaired before use. If the plug will not ﬁ t the

outlet, have a proper outlet installed by a qualiﬁ ed

electrician.

Benches

with Three Prong Plugs

Benches marked “Grounding Required” have a

power strip with a three wire cord and three prong

grounding plug. The plug must be connected to a

properly grounded outlet (See Figure A). If the

power strip should electrically malfunction or break

down, grounding provides a low resistance path to

carry electricity away from the user,

Fig. A

reducing the risk of electric shock.

The grounding prong in the plug is

connected through the green wire

inside the cord to the grounding sys-

tem in the power strip. The green wire in the cord

must be the only wire connected to the power strip's

grounding system and must never be attached to an

electrically “live” terminal.

Your power strip must be plugged into an appropriate

outlet, properly installed and grounded in accordance

with all codes and ordinances. The plug and outlet

should look like those in Figure A.

ASSEMBLY

CAUTION

Be sure to follow the assembly in-

structions for the appropriate

bench. Do not use power tools to assemble

bench. Tighten bolts with hand wrenches.

Tools Required

Phillips

screwdriver

Safety

goggles

10 mm

Wrench

13 mm

Wrench

Cabinet Shelf 1

Cabinet Shelf Clip 4

NOTE: Begin product assembly close to the ﬁ nal

intended location of your bench. This product is

heavy and may be difﬁ cult to move after assembly.

Attaching the Side Handle

Attach the side handle to the bench using four bolts

(CC). The side handle can be attached to either side

of the bench.

NOTE: The holes in the bench are tapped and do

not require nuts.

Installing the Casters

CAUTION

Two people may be required to

complete installation.

CAUTION

Do not overtighten the screws.

1. Ensure all bench drawers are securely locked into

place using the key lock on the bench.

2. Lay the bench on its back. Use the packaging

material to protect the ﬁ nish.

3. Mount the four swivel casters with brake to the

bench using four bolts (EE) and washers (DD)

per caster. The swivel casters with brake should

be installed on both ends of the bench.

4. Mount the two rigid casters in the middle of the

bench using four bolts (EE) and washers (DD)

per caster.

5. Tighten all bolts securely with a wrench.

6. Return the bench to its upright position.

Installing the Drawer Liners

Place the drawer liners in appropriately sized drawers

to protect the surface.

Installing the Bumpers

Attach the four bumpers to the bench using two

screws (FF) per bumper.

Installing the Cord Storage Brackets

Attach the brackets to the bottom right of the bench

power strip with two screws (AA) per bracket. Orient

the brackets with one pointed up and one pointed

down so that the power outlet cord can be wrapped

around the brackets for storage.

Attaching the Tool Hanger

Attach the tool hanger to the left end of the bench

using two bolts (CC).

Attaching the Storage Shelf

Attach the storage shelf to the bench using two bolts

(CC) on either end of the bench.

Positioning the Peg Board

CAUTION

Do not hang any objects on the peg

board without securing the board

in place.

The peg board is shipped and secured in its stored

location. To raise the peg board to a usable height,

remove the locking thumb screws at the top of the peg

board slides. The peg board can be raised to either

mid or full height position by pulling straight up. When

in mid or full height position, two pairs of ball detents

will temporarily hold the peg board in place. The lock-

ing thumb screw holes and the tapped holes located

in the frame of the peg board will align. Reinstall the

locking thumb screws to secure the peg board.

Hardware Included

NOTE: Items not shown to actual size.

Hard-

ware Item Description Quantity

AA Screw M4 x 10L 8

BB Screw 1/4" x

3/4"L 4

CC Bolt M6 x 15L 12

DD Washer 24

EE Bolt M8 x 15L 24

FF Screw M6 x 15L 8

Item Description Quantity

Side handle 1

Tool hanger 1

Swivel caster with

brake 4

Rigid caster 2

Bumper 4

Cord Storage

Bracket 2

Peg Board Bracket 2

Locking Thumb

Screw 2

CAUTION! The locking thumb screws must be

installed before hanging objects on the peg board.

For increased stability of the peg board, peg board

brackets and hardware are provided. To install

brackets, locate the tapped holes on both ends of

the peg board, just above the bench work surface.

Mount the peg board brackets on both ends of the

peg board frame using two bolts (CC) per bracket.

With the foot of the bracket resting in position on the

wood work surface, mark the position of each bracket

hole and drill 1/8” holes approximately ¾” deep. Use

screws (BB) to secure the peg board brackets to the

wood work surface.

Reversing the Wood Work Surface

The wood work surface comes pre-installed with

the bench. After wear and tear, the surface may

be reversed to use the clean bottom surface. To

reverse, remove the eight screws from the top of

the wood work surface, ﬂ ip surface, and reinstall

the eight screws.

OPERATION

WARNING

To avoid injury or property damage,

do not exceed maximum shelf and

drawer capacity. Use care when moving bench

on incline or rough surface. Bench may tip if

weight is not evenly distributed front to back and

side to side. Place more than half the total load

weight on the bottom drawers when possible.

Locking and Unlocking the Bench

NOTE: The drawers must be fully closed before

locking/unlocking the unit.

Insert the key. Turn it fully left to lock, or fully right

to unlock. Always remove the key after locking and

unlocking.

Product specificaties

Merk:	Milwaukee
Categorie:	Niet gecategoriseerd
Model:	48-22-8560

Heb je hulp nodig?

Als je hulp nodig hebt met Milwaukee 48-22-8560 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Milwaukee

Milwaukee L4 RLEPB Handleiding

19 November 2024

Milwaukee M18 Fuel Angler 2873B-22 Handleiding

16 November 2024

Milwaukee M18 Radius ONE-KEY 2150-20 Handleiding

25 Juni 2024

Milwaukee MXF041 Handleiding

23 Juni 2024

Milwaukee ROLL-ON 3300R Handleiding

23 Juni 2024

Milwaukee MXF NRG Handleiding

10 Juni 2024

Milwaukee TRB 1 Handleiding

10 Juni 2024

Milwaukee M12 IR-201B Handleiding

10 Juni 2024

Milwaukee L4 PPS Handleiding

10 Juni 2024

Milwaukee M12 FPTR Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Senal SCS-98 Handleiding

21 November 2024

Senal ASM-6 Handleiding

21 November 2024

Senal ASM-MNTKIT Handleiding

21 November 2024

Senal SMS-45 Handleiding

21 November 2024

Smeg KIT6PX Handleiding

21 November 2024

Senal SCI-3212MP Handleiding

21 November 2024

Matterport Pro2 3D Camera MC250 Handleiding

21 November 2024

Senal OLM-2S-P Handleiding

21 November 2024

Senal ME-220-CL Handleiding

21 November 2024

Senal ASM-4 Handleiding

21 November 2024