Mikrotik BaseBox 6 Handleiding

Mikrotik Niet gecategoriseerd BaseBox 6

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik BaseBox 6 (7 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 130 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

10.

BaseBox-series

BaseBox-seriesBaseBox-series

BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-

BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-

This User Manual covers BaseBox models:

This User Manual covers BaseBox models:This User Manual covers BaseBox models:

OUT).

OUT).OUT).

The Basebox is a solid and weatherproof outdoor device based on the RB912 wireless router model. It has high power wireless and one Gigabit Ethernet

connector, which supports MDI-X auto-detection. The device has two RPSMA connectors for connecting external antennas. The device is packaged with a

power adapter, a PoE injector, and two mounting loops. Extra places for more RP-SMA connectors are available on the unit in this case.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

This MikroTik equipment complies with the FCC, IC and European Union radiation exposure limits set forth for an

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:

uncontrolled environment.

First use

Choose your powering solution, please see the section for possibilities;Powering

Remove the lid, and connect the antenna to the RP-SMA connectors. Bend the cable with a large radius, so that it will be able to exit through the

cable openings in the bottom of the lid. Put the lid back, with a small arrow to the front of the case;

Open the device's bottom door, to reveal the Ethernet connector;

Connect your direct input power jack if not using POE, to start up the device;

Connect your Ethernet cable to the Gigabit Ethernet port;

Download WinBox configuration tool ;https://mt.lv/winbox

Open WinBox and connect to the device;

Default IP: is not set, user name: , no password, or use

admin

Neighbors tab and connect with MAC address(or, for some models, check user and

wireless passwords on the sticker);

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability;

Choose your country, apply country regulation settings, and set up your password on the screen that loads.

Mounting

The device can be mounted in several ways: wall, ceiling, pole. To tighten the device to a pole, use the provided metal hose clamp.

Guide the loop around the device through the provided holes, and around the pole where it will be mounted, or use a DIN mount to attach the device to a

rail:

You should avoid connecting a loose Ethernet cable to the Ethernet port, secure the cable to a wall or the pole, so that the cable weight is not pulling the

port. It is recommended to secure the Ethernet cable less than 2m from the device. This is to ensure that the cable doesn't damage the port by its weight,

or doesn't fall out. It is possible to connect grounding wires to the PCB board mounting holes, but to do this, you must remove the PCB from the case.

Powering

The device accepts power from the power jack or from the Ethernet port:

Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 24 V DC.

Ethernet port accepts passive Power over Ethernet 18-57 V DC (Please compensate voltage for loss due to cable length)

The power consumption under maximum load can reach 12 W. For BaseBox 6 model up to 23 W.

Configuration

RouterOS includes many configuration options in addition to what is described in this document. We suggest

starting here to get yourself accustomed to the possibilities: . In case IP connection is not available,https://mt.lv/help

the Winbox tool ( ) can be used to connect to the MAC address of the device from the LAN sidehttps://mt.lv/winbox

(all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device from the network, see a section .Reset button

Expansion Slots and Ports

BaseBox 2 model - 2.4 GHz, 802.11b/g/n.

BaseBox 5 model - 5 GHz, 802.11a/n.

BaseBox 6 model - 6 GHz, 802.11a/n.

One 10/100/1000 Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or

crossover cable for connecting to other network devices.

USB type-A slot.

One miniPCIe slot.

This device might be incompatible with the R11e-LTE international modem.

The miniPCI-e slot usage

Warning! This equipment should be installed and operated with a minimum distance of 380 cm between the device and your body. Operation of

this equipment in the residential environment could cause radio interference.

Remove top cover;

Unscrew two screws on the back of the device;

Open Ethernet port cover and withdraw it from the base of the device;

Unscrew the antenna connector;

Withdraw the PCB plate from the base cover;

Install your modem and reassemble.

Reset button

The reset button has three functions:

Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).

Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10

seconds).

Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15

seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Product specificaties

Merk:	Mikrotik
Categorie:	Niet gecategoriseerd
Model:	BaseBox 6
Kleur van het product:	Wit
Breedte:	246 mm
Diepte:	135 mm
Hoogte:	50 mm
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Vermogensverbruik (max):	23 W
Aansluiting voor netstroomadapter:	Ja
Intern geheugen:	64 MB
Type processor:	Ja
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.11a, IEEE 802.11n
Intern:	Nee
Flash memory:	128 MB
Maximale overdrachtssnelheid van gegevens:	- Mbit/s
Power over Ethernet (PoE):	Ja
AC-ingangsspanning:	10 - 30 V
Stroomverbruik (typisch):	12 W