Miele Professional PT 8337 Handleiding

Miele Professional Wasdroger PT 8337

Lees hieronder de 📖 handleiding in het Nederlandse voor Miele Professional PT 8337 (74 pagina's) in de categorie Wasdroger. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/74

Operating instructions

Dryers

Gebruiksaanwijzing

Droogautomaten

PT 8257

PT 8337

PT 8407

PT 8507

PT 8807

To avoid the risk of accidents or damage to the machine it is

essential to read these instructions before installing,

commissioning and using it for the first time. M.-Nr. 07 713 432

en, nl - GB, NL

This machine must be installed in accordance with local and national building and safety regulations by a

suitably qualified engineer. In the U.K. this must be done for gas-heated machines by a Gas Safe registered

engineer. Adequate ventilation must be present in the room in which the machine is operated.

It is essential to read these instructions before installing and operating the machine.

Gas-heated machines

Safety precautions to take if you smell gas

– Turn off the gas emergency control valve immediately. This is usually located near the gas meter.

– Do not enter a room with an open flame where there is a smell of gas.

– Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches.

– Do not operate electrical lights or switches, i.e. do not switch them "On" or "Off".

– Open all windows and doors to ventilate the area.

– If the smell of gas persists, evacuate the building.

In the UK you must now:

- Call the Gas Emergency Contact Centre (Tel: 0 800 111 999)

- For any gas work in the UK always use a Gas Safe registered engineer.

In other countries please follow relevant country specific procedures on gas.

Keep these instructions in a safe place and ensure they are made available to new users. They must be made

aware of these Warning and Safety instructions.

All personnel working with this machine must be fully trained in all aspects of its use and safety.

Gas safety precautions

Gas safety precautions ......................................................................2

Warning and Safety instructions...............................................................4

Caring for the environment ...................................................................6

Guide to the machine ........................................................................7

Control elements.............................................................................8

Drying....................................................................................10

Sort the laundry.............................................................................10

Before using for the first time ..................................................................11

Switch the machine on and load the drum ........................................................11

Select a programme .........................................................................12

Card operation / coin mechanism .............................................................15

Card access operation .......................................................................15

Drying using coin mechanism C 4060 / C 4065 / C 4070 .........................................15

Additional options .........................................................................16

Start date and time ..........................................................................16

Programme stop ............................................................................17

Programme cancellation......................................................................17

Changing the programme order................................................................17

Programme information ......................................................................17

Programme overview .......................................................................18

Standard programmes .......................................................................18

Duvets....................................................................................20

Mops (Buildings maintenance).................................................................20

Fire service ................................................................................21

Professional cleaners ........................................................................21

Optional modules ..........................................................................23

Operating data .............................................................................23

Peak load cut-out ...........................................................................24

Problem solving guide ......................................................................25

Error messages.............................................................................25

After sales service ..........................................................................26

Cleaning and care ..........................................................................27

Fluff filter ..................................................................................27

Installation and connection ..................................................................28

Levelling the machine........................................................................29

Installation on a raised plinth ..................................................................29

Coin mechanism ............................................................................29

Communication module XKM RS232 ............................................................29

Electrical connection ........................................................................30

Air inlet and exhaust connection ...............................................................30

Steam connection ...........................................................................30

Hot water connection ........................................................................30

Gas connection.............................................................................30

Technical data .............................................................................31

Explanation of symbols on the data plate ......................................................32

Abbreviated operating instructions PT 8257 / 8337 / 8407 / 8507 / 8807..............................33

Contents

Explanation of the Warning and Safety

symbols on the machine

It is essential to read these operating

instructions.

Please refer to specific instructions, e.g.

Installation instructions

Caution, hot surfaces.

Caution, voltage up to 1000 volts.

Earthing

To avoid the risk of accidents and damage to the

machine read the operating instructions carefully

before using it for the first time. They contain

important information about the installation, safety,

use and maintenance of the machine. Keep them

in a safe place and ensure that new users are

familiar with the content. Pass them on to any

future owner of the machine.

Correct application

~This dryer must only be used for drying articles

which were washed in water and which have a care

label stating that the article is suitable for machine

drying.

~To prevent the risk of fire, the following must

not be dried in this tumble dryer (with the exception

of those fabrics which can be dried in the Special

Programmes specifically designed for them):

– fabrics which contain a large proportion of rubber,

foam rubber or rubber-like materials.

– items which have been treated with inflammable

cleaning agents.

– items which have been splashed with hair lacquer,

hair spray, nail varnish remover or similar

substances.

–items which have been soiled with oils or residues

containing grease (kitchen oils, cosmetics etc.).

–items soiled with wax or other chemicals (e.g.

mops and floor cloths).

–items with damaged padding or fillings (e.g.

pillows, jackets).

–items soiled with grease or oil which have not been

properly cleaned beforehand. Use heavy-duty

detergents where necessary to clean heavily soiled

garments, e.g. workwear. If necessary consult the

detergent manufacturer for advice.

With sensitive fabrics there may be a danger of them

self igniting if dried for too long. They should be

removed as soon as the programme has finished or if

there is a power cut.

Keep a fire extinguisher near the machine at all times.

~Do not unload laundry from the drum until the

cooling down phase has been completed.

Hot laundry can self ignite and cause a fire when

folded or put away.

~Check that all pockets of workwear etc are empty

to avoid the danger of inflammable objects, e.g.

cigarette lighters, matches, candles or cosmetics

being placed in the dryer.

~If the dryer is installed in a public area the owner

must ensure that it can be operated safely.

~This dryer must not be used outside.

Technical and electrical safety

~This machine must only be installed and

commissioned by a Miele authorised technician.

~The electrical safety of this machine can only be

guaranteed if connected to a correctly installed

earthing system on site. It is most important that this

basic safety requirement is present and tested

regularly, and where there is any doubt, the on-site

electrical wiring should be inspected by a qualified

electrician. The manufacturer cannot be held liable

for the consequences of an inadequate earthing

system (e.g. electric shock).

~The machine is only completely isolated from the

electricity supply either when it is switched off at the

isolator switch or the mains fuse has been withdrawn.

~Repairs to electrical and gas heated appliances

should only be carried out by a suitably qualified and

competent person in accordance with local and

national safety regulations. Repairs and other work by

unqualified persons could be dangerous. The

manufacturer cannot be held liable for unauthorised

work.

~Faulty components must only be replaced by

genuine Miele original spare parts. Only when these

parts are fitted can the safety standards of the

machine be guaranteed.

~This machine must not be operated in the same

room as dry cleaning machines which use solvents

containing chlorofluorocarbons (CFCs). Escaping

vapours break down during combustion into

hydrochloric acid which can have a detrimental effect

on both the laundry and the machine. Even when

such machines are installed in separate rooms, care

should be taken to ensure that no exchange of air

can take place.

Warning and Safety instructions

~The dryer must have a constant supply of fresh air.

Vapours containing chlorine, fluorine or other solvents

must not be able to reach the dryer.

~The ventilation inlet to the dryer is located at the

back of the machine. It must not be blocked or

hindered in any way. Do not cover the machine lid

with cloths or similar items.

~Benzine, petrol, paraffin or any easily flammable

substance must not be stored or used near the

tumble dryer. Fire and explosion risk.

~To ensure the correct performance of the machine

and to prevent the risk of faults and fire, it is important

to check the machine and carry out maintenance on

a regular basis.

Use

~This tumble dryer must only be used when it is

connected to a suitable ducting system. The

installation site must be adequately ventilated.

~This tumble dryer is not intended for use by

people with reduced physical, sensory or mental

capabilities, or lack of experience or knowledge,

unless they are supervised whilst using it or have

been shown how to use it by a by a person

responsible for their safety.

~Keep children away from the tumble dryer at all

times. It is not a toy! To avoid the risk of injury do not

allow them to play on or near it or to play with the

controls. Supervise children whilst you are using it.

~Always close the drum door and the fluff filter

compartment after use to avoid:

– the risk of children hiding things in the dryer

– the risk of children and small animals climbing into

the drum and endangering their lives.

~Do not use a machine with damaged controls or

cables. These must be repaired before it is used

again.

~Do not damage, remove or bypass the safety

features, fixtures and control elements of this

machine.

~Any removable outer panels must be back in

place, and all moving or electrical parts shielded

before the machine is switched on.

~Whilst the dryer is in use the porthole glass and

drum door frame can become very hot. Laundry will

also be very hot if you remove it early.

~To prevent the risk of injury or scalding

components carrying steam must not be touched.

~Always make sure that the drum is stationary

before reaching into the machine to remove laundry.

Reaching into a moving drum is extremely

dangerous.

~Take care near the drum door hinges and the fluff

filter compartment flap. Danger of injury. Ensure that

you always use the handles.

~The drum door must be able to be opened to its

fullest extent. This area must not be restricted by

doors or structural features.

~Do not use the machine without the built-in fluff

filter in place. Fire risk.

A damaged fluff filter must be replaced before the

machine is used again.

Otherwise fluff and lint will cause a blockage in the

airways, the heating and the vent ducting, and the

correct functioning of the machine cannot be

assured.

~Cleaning and disinfecting agents often contain

chlorine-based substances. Do not let such agents

come into contact with the stainless steel surfaces, as

the chlorine can have a corrosive effect and cause

rust. Use chlorine-free agents for washing and

disinfecting and also for cleaning stainless steel

surfaces to protect them from corrosion. If in doubt,

confirm with the manufacturer that their product is

suitable. If any agent containing chlorine comes into

contact with the stainless steel surfaces, wipe it away

immediately with clean water. Then dry with a soft

cloth.

~Do not use a pressure washer or hose to clean the

machine.

Gas heated dryers

~The gas mains connection point and the gas

connection to the machine should be switched off for

all cleaning and maintenance work and in the event

of a fault.

~Warning. After commissioning the machine, and

after any maintenance, conversion or repair work all

components carrying gas from the gas tap to the

burners should be tested for leakage. Test points on

the gas tap and the burner are particularly important.

The machine should be tested with the burner

switched on and switched off.

Using accessories

~Accessory parts may only be fitted when

expressly approved by Miele. Using spare parts or

accessories from other manufacturers will invalidate

the guarantee, and Miele cannot accept liability.

Disposing of your old machine

~Before disposing of an old machine, first make the

door lock unusable. This way you will prevent

children from accidentally locking themselves in and

endangering their lives.

Keep these instructions in a safe and

accessible place.

Warning and Safety instructions

Disposal of the packing material

The transport and protective packing has been

selected from materials which are environmentally

friendly for disposal.

Rather than just throwing these materials away,

please ensure they are recycled.

,Ensure that any plastic wrappings, bags, etc

are disposed of safely and kept out of the reach of

babies and young children. Danger of suffocation.

Disposing of your old machine

Electrical and electronic machines often contain

materials which, if handled or disposed of incorrectly

could be potentially hazardous to human health and

to the environment. They are, however, essential for

the correct functioning of your machine. Please do

not therefore dispose of it with your household waste.

Please dispose of it at your local community waste

collection / recycling centre or contact your Dealer for

advice. Ensure that it presents no danger to children

while being stored for disposal.

See the "Warning and Safety" section of this booklet

for further details.

Tips on saving energy

Make sure that your laundry is thoroughly spun

before drying. This saves time and energy.

Rinsing the laundry using hot water in the final rinse

helps to reduce the residual moisture level, and the

residual heat in the laundry will help keep processing

time down, thus saving energy.

Sort textiles according to:

- fabric and weave,

- drying level required,

- residual moisture levels.

For greater economy dry a full load. Underloading is

uneconomical. Overloading will impair the drying

result and the laundry finish.

Ensure that the room is well ventilated.

Caring for the environment

aEmergency stop switch

Only for use in an emergency.

Once the danger is no longer present, turn the

grooved disc clockwise to disengage the switch.

Do not use the Emergency stop switch to turn off

the dryer in normal use.

bControl panel

cDrum door

Pull the door handle to open the drum door.

dAccess to fluff filter

Pull the handle to open the fluff filter compartment.

e4 adjustable screw feet

fElectrical connection

gAir intake

hExhaust connection

iEquipotential bonding

jCommunication slot

Guide to the machine

Control elements

aDisplay

1 Cottons extra dry 0%

2 Cottons dry 0%

3 Cottons damp 20%

FC A

After switching on, the "Welcome" display will appear

for a short time followed by the programme list. The

most recently used programme is highlighted.

bFunction buttons

The six buttons underneath the display are the

function buttons. These buttons have specific

functions depending on the status of the machine.

These functions will be listed in the display above the

buttons and will be highlighted once selected.

If the machine is reprogrammed to "Direct button

allocation" the first 6 programmes listed in the display

can be selected directly via these buttons.

cStart button

The lightring will flash when a selected programme

can be started. Pressing the Start button will start the

programme. After a programme has started, pressing

this button will show the display as it was before the

start of the programme.

dPC / Optical interface

This interface is used for transferring data to the

control unit from a PC and vice versa.

eRotary selector

Turning the selector brings up options and menus in

the display.

Pressing the selector confirms your selection.

fChip card reader (optional)

If the machine has been programmed for card

operation, you can only use those programmes

stored on the card to dry laundry.

Insert the card in the direction of the arrow (on the

card).

gI Mains on switch

Switches the machine on.

h0 Mains off switch

Switches the machine off.

Guide to the machine

Function buttons

fStop/End

The function button on the right-hand side is used to

stop a programme after it has started. Pressing it

again finishes the programme.

[Block plus

The relevant programme block (e.g. Pre-dry) is

added to the programme.

FCSettings

Press this button to switch to another

language temporarily.

mStart time

Pressing this button before the start of a programme

displays the message that a start time can be

selected.

KInformation

Press this button to call up programme

information in the display.

üChange order

The order of the programme in progress can be

changed or programme blocks can be repeated.

ABack

Takes you back to the previous display.

e/-Indicates that there is more

information on next or previous line.

SSave

See the programming instruction booklet.

$Programme locked

Once a locked programme has been started, the End

button can only be used to stop and cancel it during

the first minute.

%Programme unlocked

\Operating data

Data transfer

Chip card operation

The chip card is supplied without any programmes.

See the programming instruction booklet for

information on transferring data from the control unit

to the chip card and vice versa.

The chip card can store a maximum of 30

programmes, each with 6 blocks.

The back of the chip card can be labelled.

Guide to the machine

Sort the laundry

Not all textiles are suitable for machine drying.

Please read the instructions given on the garment

care label.

The meaning of the care symbols:

q= Dry at normal temperature

r= Dry at low temperature

s= Do not tumble dry

Sort the laundry according to fibre type and weave to

ensure even drying and to prevent the risk of damage

to textiles.

,To prevent the risk of fire, the following

must not be dried in this tumble dryer (with the

exception of those fabrics which can be dried in

the Special Programmes specifically designed for

them):

- fabrics which contain a large proportion of

rubber, foam rubber or rubber-like materials.

- items which have been treated with inflammable

cleaning agents.

- items which have been splashed with hair

lacquer, hair spray, nail varnish remover or similar

substances.

- items which have been soiled with oils or

residues containing grease (kitchen oils,

cosmetics etc.).

- items soiled with wax or other chemicals (e.g.

mops and floor cloths).

- items with damaged padding or fillings (e.g.

pillows, jackets).

- items soiled with grease or oil which have not

been properly cleaned beforehand. Use

heavy-duty detergents where necessary to clean

heavily soiled garments, e.g. workwear. If

necessary consult the detergent manufacturer for

advice.

The following textiles should not be machine

dried:

Woollens and wool blends as these tend to matt and

shrink. Pre-finish drying these using in the "Woollens"

programme.

Pure linen tends to roughen if tumble dried. Please

follow instructions given on the care label.

Important:

Textiles with large metal accessories such as

buckles, hooks and zip tags should be placed in a

laundry bag or a pillow case before drying. This is to

protect the drum from scratches and dents during

drying.

Garments with closed metal zips can cause the

sensor electrodes in the drum ribs to be bridged.

This can cause the drying process to go on for too

long, or to not finish at all. Open zips before drying.

Loopknit and woven textiles (e.g. T-shirts and

underwear) have a tendency to shrink depending on

their quality. This is made worse by over-drying. Do

not use the "Cottons extra dry" for these textiles.

Starched laundry can be machine dried. Select the

most appropriate programme for ironing by hand or

machine.

Sort the laundry according to the level of dryness

required. It is not necessary to sort according to size.

Duvet covers and pillow cases should be closed to

prevent smaller items rolling up inside them.

For greater economy dry a full load. Underloading is

uneconomical. Overloading will impair the drying

result and the laundry finish.

Rinsing the laundry using hot water in the final rinse

helps to reduce the residual moisture level, and the

residual heat in the laundry will help keep processing

time down, thus saving energy.

Drying

The machine must be commissioned by a Miele

authorised technician before it is used for the first

time. For gas heated machines in the U.K. this

must be carried out by a Gas Safe registered

technician.

Before using for the first time

Before loading the dryer with laundry you should wipe

the internal drum surface with a soft, dry cloth.

Switch the machine on and load the drum

^Open all stopcocks for gas and steam as

applicable.

^Switch on the on-site mains switch.

^Press the I"On" button in.

The Welcome screen will appear.

Miele

PROFESSIONAL

PT 8xx7

Welcome

This is followed by the programme list (with the most

recently used programme highlighted).

1 Cottons extra dry 0%

2 Cottons dry 0%

3 Cottons damp 20%

FC A

Select a programme using the rotary selector.

^Open the drum door.

^Load the drum.

The pre-sorted laundry should be loaded loosely in

the drum.

Make sure any dispensing aids such as detergent

balls have been removed from the laundry.

Max. load (dry weight of laundry)

PT 8257 PT 8337 PT 8407 PT 8507 PT 8807

Drum volume in litres

250 325 400 500 800

1, 2, 3, 4, 5 Cottons

10-13 kg 13*-16

16*-20

20*-25

32*-40

6, 7, 8 Minimum iron

5kg 6.6kg 8kg 10kg 16kg

9 Woollens

4 kg 5.2 kg 6.4 kg 8 kg 12.8 kg

10 Delicates / Synthetics

2 kg 2.6 kg 3.2 kg 4 kg 6.4 kg

11, 12 Timed drying programmes

10-13 kg 13*-16

16*-20

20*-25

32*-40

13, 14 Proofing, Outerwear

5-6.6 kg 6.6-9 kg 8-11 kg 10-13 kg 16-20 kg

* Hot water machines

To prevent the risk of damaging laundry make

sure it cannot be trapped when the door is closed.

^Close the drum door.

Drying

Select a programme

This machine is equipped with an electronic sensor

system that continually monitors the moisture level of

the laundry.

As soon as the required dryness is reached the

laundry is cooled down. At the end of this cooling

down phase the drying programme is automatically

finished.

Standard programmes:

– For drying cotton and linen textiles

1 Cottons extra dry 0 %

2 Cottons dry 0 %

3 Cottons damp 20 %

4 Cottons damp 25%

5 Cottons damp 40 %

– For drying synthetic and mixed fibre textiles

6 Minimum iron dry 0 %

7 Minimum iron damp 10 %

8 Minimum iron damp 20 %

9 Woollens 5 min.

10 Delicates 20 %

– For airing textiles

11Timed drying cold air 15 min.

– For drying small loads of laundry or for

finishing drying individual items.

12Timed drying hot air 20 min.

1 Cottons extra dry 0%

2 Cottons dry 0%

3 Cottons damp 20%

FC A

^Turn the rotary dial to select a programme (e.g.

Programme 2Cottons dry).

Select the additional option ["Blockplus" if

required

(this is not available on standard programmes)

^Confirm the selection of the programme by

pressing the rotary selector.

The following (example) will appear in the display:

22 Cottons dry 10.0 / 13.0 kg

0 % Drying 70°C

Cooling down e

[mA

^If wished you can now select a programme block,

e.g. Pre-drying by pressing the ["Blockplus"

function button.

When the ["Blockplus" function button is pressed,

the following will appear in the display:

2 2 Cottons dry 10.0 / 13.0 kg

24 % Pre-drying

0 % Drying e

[mA

The [field is highlighted.

Press the function button again to deselect the

function.

If you do not wish to make any further alterations to

the programme:

^Press the "Start" button. The programme will start.

If you wish to make alterations before the start of

the programme, e.g. to the load size, temperature

or residual moisture:

^Confirm the selection of the programme by

pressing the rotary selector.

The following (example) will appear in the display:

2 Cottons dry 10.0 / 13.0 kg

0 % Drying 70°C

Cooling down e

The max. load will be shown at the far right of the

display.

Drying

Load weight

You can enter the weight of the load manually before

the start of the programme.

2 Cottons dry 10,0 13.0 kg

0 % Drying 70°C

Cooling down e

^Turn the rotary dial to highlight the load. Press the

dial to confirm your selection. Turn the dial to alter

the weight and confirm your selection by pressing

it.

Temperature in 1 °C increments from cold, 30 to

max. 80 °C .

^Turn the rotary dial to select the "Temperature" field

(70 °C for drying) and press it to confirm your

selection.

2 Cottons dry 13.0 kg

0 % Drying 70°C

Cooling down e

^Turn the rotary dial to alter the temperature value

and then press it to confirm your selection.

Residual moisture in 1 % increments from -4 to 40 %.

^Turn the rotary dial to select the "Residual moisture"

field (0 %) and press it to confirm your selection.

2 Cottons dry 13.0 kg

0% Drying 70°C

Cooling down

^Turn the rotary dial to alter the residual moisture

level and then press it to confirm your selection.

^Press the Start button and the programme selected

will commence

Once a programme has started the programme

sequence will appear in the display.

2 Cottons dry

0 % Drying >40 %{

Cooling down Ready at 12:35

mKf

In the 2nd line of the display, drying in this example,

the actual residual moisture level (>40%) and the

symbol for {Electric or *Gas heating switched on

will also be shown. The 3rd line displays the following

programme block.

The time that the programme will finish (12:35) is

shown on the right hand side of the display.

The programme end display has a self-learning

function and will not show an accurate reading until

the programme has been run several times.

At the end of a programme

2 Cottons dry

Programme finished

Anti-crease Ready at 12:35

mFC Kf

The programme end time is displayed,the buzzer

sounds and the anti-crease phase commences. The

drum will rotate at intervals to keep the laundry from

creasing.

This is useful if laundry is not going to be unloaded as

soon as the programme finishes.

^Open the drum door.

^Unload the drum.

Make sure nothing is left behind in the drum. If

items are left in the dryer, they could be damaged

by overdrying when the dryer is next used.

,Do not unload laundry from the drum until after

the cooling down phase has been completed.

Hot laundry can self-ignite and cause a fire when

folded or put away.

^Check the fluff / lint filter and clean if necessary.

2 Cottons dry

Programme finished

Check lint filter A

A reminder will appear in the display when the filter

need to be cleaned. The filter should be cleaned as

soon as the programme finishes.

Drying

If no more laundry is to be processed:

^Close the drum door

^Press the 0"Off" button to switch the machine off.

^Switch off the on-site mains switch.

^Close all stopcocks for gas and steam as

applicable.

Adding or removing items

The drum door can be opened during a drying

programme to remove or add items if necessary.

,Always make sure that the drum is stationary

before reaching into the machine to remove

laundry. Reaching into a moving drum is extremely

dangerous!

2 Cottons dry

Programme stop

Door open. Please close the door.

FC f

To continue the drying programme:

^Close the drum door

The fan will switch itself on automatically if the

temperature in the drum is too high.

^Press the "Start" button and the programme

selected will continue.

Drying

Cards on which a programme has been saved can

only be used on the machine type for which they

have been written.

Unwritten cards can be used universally.

^Press the "On" Ibutton to switch the

machine on.

The Welcome screen will appear.

^Insert the card in the reader.

The programmes listed on the card will

appear in the display.

Card operation

17 Protective clothing 45 °C

18 Minimum iron 60 °C

FC A

^Use the rotary selector to highlight the programme

you want to use. Press the rotary dial to select the

programme you have highlighted.

^Press the Start button. The programme will start.

After pressing the "Start" button you can remove the

card from the reader. The programme is deleted from

the machine's memory once it has finished.

,Never insert any other card or object into the

card reader!

If the card is inserted the wrong way round the

following message will appear in the display:

§Card fault

Card incorrectly inserted in card reader.

üA

^Insert the card the right way round in the card

reader.

If the card is not the right one for the machine it is

being used in, the following message will appear in

the display:

Card operation

Programmes on the card are only suitable

for machine type PT 8507 A

^Insert the correct card for the machine in the card

reader.

Card access operation

Programmes requiring special procedures are written

onto a card which is then used to run the programme.

"Card access" has be activated via the supervisor

level in the machine.

The machine will then only run programmes by using

a card (on which one programme has been saved).

Programmes in the machine's control unit cannot then

be accessed.

Drying using coin mechanism C 4060 /

C 4065 / C 4070

If the machine is not operated in the following order

you will lose your money or tokens!

ALoad the drum and close the door.

BPress the I"On" button.

CSelect a programme

DInsert coins or tokens.

EPress the "Start" button.

Card operation / coin mechanism

Language selection

The language shown in the display can be changed

briefly before starting a programme if you wish. To do

so use the button underneath the flag symbol.

1 Cottons extra dry 0%

2 Cottons dry 0%

3 Cottons damp 20%

FC A

If you press the FC button the following will appear

in the display:

Settings Back <-

Main menu Language

Supervisor level

FC A

^Press the rotary dial to confirm your selection of the

"Language" menu.

Settings deutsch

Language Fenglish (GB)

español

FC A

^Turn the rotary dial to highlight the language you

want and then press the dial to confirm your

selection.

The FC function button can be pressed to change

to a different language temporarily. By highlighting

the language the display will immediately change to

show the language selected. If the programme is not

started, or no other buttons or controls are activated

in the next 5 minutes the language will revert back to

the default setting.

The language will revert back to the default setting 5

minutes after the end of a programme with the door

open.

Start date and time

If you want a programme to start at a later time use

the mbutton for "Start date and time".

To set a date and time

After selecting your programme, the following

(example) will appear in the display:

2 Cottons dry 13.0 kg

0 % Drying 70°C

Cooling down e

^Press the m"Start date and time" button.

The following (example) will appear in the display:

2 Cottons dry 13.0 kg

Start time: 16 : 10 Start date: 2.4.2003

After selection press the start button.

The current time and date will then appear. The input

field for hours will be highlighted.

^Press the rotary dial to change the hour.

Turn the rotary dial to alter the hour and then press

it to confirm your selection.

^Then turn the rotary dial to select the "Minutes" field

and press it to confirm your selection.

Turn the dial to alter the minutes and then press it

to confirm your selection.

^Then turn the rotary dial to select the "Start date"

field and press it to confirm your selection.

Turn the dial to alter the date and then press it to

confirm your selection.

^Do the same for the month and the year.

After setting the required start date and time:

^Press the Start button and the programme selected

will commence at the time specified.

The display will now contain the following information:

2 Cottons dry 13.0 kg

0 % Drying

16:15 -2.4.2009 Start 6:00-3.4.2009

The current time and date as well as the start time will

be displayed.

^If the door is opened again you will have to press

the Start button again.

To cancel the start time and date function

Press the m"Start date and time" button again or

press A"Back", and any changes will be rejected.

Additional options

Programme stop

To halt the programme press the fbutton.

The programme remains stationary.

2 Cottons dry

Programme stop

Press the start button.

üf

To continue the programme press the "Start" button.

Programme cancellation

To cancel a programme press the f"Stop/End"

button twice in succession.

Changing the programme order

The order of the programme in progress can be

changed or programme blocks can be repeated.

^Press the fbutton and the programme will stop.

2 Cottons dry

Programme stop

Press the start button.

üf

^After pressing the übutton the current area or

block will appear in the display.

See also "Programme structure" in the Progamming

Manual.

Reorganise -> 2 Cottons dry

Programme stop

Area 1: Drying e

Area 1: Drying

Block 1: Pre-drying

^Turn the rotary dial to select the area, and then

press it to confirm your selection.

Select Area: 1 Drying, or 2 Cooling down and

confirm your selection.

^Turn the rotary dial to select the block and then

press it to confirm your selection.

Select Block: Drying 1-10, or Cooling down 1-10

and confirm your selection.

^Press the S"Save" button and then press "Start" to

reorganise the programme order or press the A

"Back" button to go back to programme stop and

not change the programme order.

Programme information

Pressing the K"Information" button will call up further

information about the programme e.g.:

2 Cottons dry

Start date and time: 10.7.2009

Start time: 9:47 e

mKf

Time after start: 0h 23 min

Time left: 0h 11min

Progr.-End: 10: 21 h e

Area: 1 Drying

Block: 1 Pre-drying

Actual exhaust air temp. 59 °C e

Rqrd. exhaust air temp. 74 °C

Peak load: No

Anti-crease: 3 s./87s./60 min e

2 Cottons dry

Exhaust / Recirculation: Recirculation -

Block end signal Yes A

^Press the A"Back" button to return to the

programme sequence display.

Additional options

Standard programmes

Programme Fabric type max. load capacity

(kg, dry weight)

1 Cottons extra dry 0 %

(Normal+) 74°C

Multi-layered and bulky cotton and linen textiles which do

not get dry in the Cottons dry programme.

PT 8257 10-13

PT 8337 13-16

PT 8407 16-20

PT 8507 20-25

PT 8807 32-40

2 Cottons dry 0 %

(Normal) 74°C

Single and multi-layered cotton and linen textiles.

3 Cottons damp 20 %

(Machine iron) 74°C

Cotton and linen textiles which are to be machine ironed.

4 Cottons damp 25%

(Machine iron) 74°C

5 Cottons damp 40 %

(Machine iron) 74°C

6 Minimum iron dry 0 %

(Normal) 60°C

Synthetic, cotton and mixed fibre textiles which are to be

machine ironed.

PT 8257 5.0 kg

PT 8337 6.6 kg

PT 8407 8.0 kg

PT 8507 10 kg

PT 8807 16 kg

7 Minimum iron damp 10 %

(Machine iron) 60°C

8 Minimum iron damp 20 %

(Machine iron) 60°C

9 Woollens

(5 min.) 74°C

For fluffing up woollen garments. This programme does

not dry woollens.

PT 8257 4

PT 8337 5.2

PT 8407 6.4

PT 8507 8

PT 8807 12.8

10 Delicates 20 %

40°C

Delicate cotton, synthetic and mixed fibre fabrics. PT 8257 2

PT 8337 2.6

PT 8407 3.2

PT 8507 4

PT 8807 6.4

11 Timed drying cool air

(15 min.)

Items which need airing only.

PT 8257 10-13

PT 8337 13-16

PT 8407 16-20

PT 8507 20-25

PT 8807 32-40

12 Timed drying hot air

(20 min.) 74°C

For drying small loads of laundry or for finishing drying

individual items.

Programme overview

Programme Fabric type max. load capacity

(kg, dry weight)

13 Proofing

(Normal) 60°C

For drying microfibre fabrics, skiwear, fine, closeweave

cotton garments (poplin) or tablecloths which are

suitable for drying in a tumble dryer and have been

treated to provide a water and dirt resistant finish. PT 8257 5 - 6.6

PT 8337 6.6 - 9

PT 8407 8 - 11

PT 8507 10 - 13

PT 8807 16 - 20

This programme includes a proofing fixing phase.

Only use proofing agents containing fluorochemical compounds which are stated by the

manufacturer as being "suitable for use on membrane textiles".

Fire hazard. Do not dry items which have been treated with proofing agents containing

paraffin.

14 Outerwear

60°C

Outerwear which is suitable for drying in a tumble dryer.

Temperatures given refer to extracted air temperature.

Programme overview

Duvets

Programme Fabric type max. load capacity (kg, dry weight)

Down duvets Feather and down filled duvets and pillows. PT 8257 1 single duvet or 2 pillows (10)

PT 8337 3 pillows or (13)

1 pillow + 1 single duvet

PT 8407 4 pillows or (16)

2 pillows + 1 single duvet or

2 single duvets

PT 8507 5 pillows or (20)

3 pillows + 1 single duvet or

2 single duvets

PT 8807 8 pillows or (32)

3 pillows + 3 single duvet or

4 single duvets

The loads quoted are estimates and will

vary depending on the size and volume

of the duvets.

74°C, Dries to 0 % residual moisture, Tumble phase, Cooling down

phase

Synthetic duvets Synthetic duvets and pillows.

74°C, Dries to 0 % residual moisture, Tumble phase, Cooling down

phase

Natural fibre blankets Natural fibre quilts and blankets.

74°C, 3 min. drying phase, Cooling down phase.

Natural fibre blankets and quilts must not be dried completely in a

tumble dryer, as this could cause the fibres to matt. These should

only be partially dried in a tumble dryer.

Mops (Buildings maintenance)

,Items that have not been washed thoroughly and may still contain residual wax or chemicals are a fire

hazard.

Wash heavily soiled items very thoroughly before drying them, ensuring that you use sufficient detergent and

select a high temperature. If in doubt, wash the items several times.

Programme Fabric type max. load capacity

(kg, dry weight)

Mops Cotton mops PT 8257 10

PT 8337 13

PT 8407 16

PT 8507 20

PT 8807 32

74°C, Dries to 0 % residual moisture, Cooling down phase.

Microfibre mops Microfibre mops

60°C, Dries to 0 % residual moisture, Cooling down phase.

Cleaning cloths Microfibre cloths, dusters PT 8257 5.6

PT 8337 7

PT 8407 8.6

PT 8507 11

PT 8807 17.6

60°C, Dries to 0 % residual moisture, Cooling down phase.

Temperatures given refer to extracted air temperature.

Programme overview

Fire service

Programme Fabric type max. load capacity (kg, dry weight)

Face masks Face masks with

head straps

max. no. holders / masks

PT 8257 4 8

PT 8337 4 12

PT 8407 4 16

PT 8507 4 12

PT 8807 4 16

50°C, 45 min. drying phase, Cooling down phase.

Breathing masks may only be dried if special holders (available as an

optional accessory) are fitted in the drum.

Protective clothing Protective clothing (e.g. as used by the fire

brigade), overalls, jackets, trousers

PT 8257 approx.1-2suits

(1 jacket + 2 trousers or 2 jackets)

PT 8337 approx. 2 suits (or 3 jackets)

PT 8407 approx. 3 suits

PT 8507 approx.3-4suits

PT 8807 approx. 6 suits

PT 8257 5 - 6.6 kg

PT 8337 6.6 - 9 kg

PT 8407 8 - 10 kg

PT 8507 10 - 13 kg

PT 8807 16 - 20 kg

74°C, Dries to 0% residual moisture, Tumble phase, Cooling down

phase

For best results, dry items inside out.

Reproof protect.

clothing

For all textiles that have been treated with a

proofing agent

74°C, Dries to 0 % residual moisture, Tumble phase, Cooling down

phase

Only use proofing agents containing fluorochemical compounds which

are stated by the manufacturer as being "suitable for use on membrane

textiles".

Fire hazard. Do not dry items which have been treated with proofing

agents containing paraffin.

Professional cleaners

Programme Fabric type max. load capacity (kg,

dry weight)

WetCare sensitive For non washable garments PT 8257 approx.4-5

PT 8337 apporx.5-6.6

PT 8407 approx. 6.6 - 8

PT 8507 approx.8-10

PT 8807 approx. 16 - 21

50°C, 3 min. drying phase, Cooling down phase.

WetCare silks For non washable garments which crease easily PT 8257 approx.4-5

PT 8337 approx.5-6.6

PT 8407 approx. 6.6 - 8

PT 8507 approx.8-10

PT 8807 approx. 13 - 16

60°C, Dries to 15 % residual moisture, Cooling down phase.

WetCare intensive Washable garments PT 8257 approx.5-6.6

PT 8337 approx. 6.6 - 9

PT 8407 approx.8-11

PT 8507 approx. 10 - 13

PT 8807 approx. 16 - 21

74°C, Dries to 0 % residual moisture, Cooling down phase.

Temperatures given refer to extracted air temperature.

Programme overview

Equestrian

,Metal buckles and fasteners etc. should be removed to protect the items being dried and the drum. If it is

not possible to remove them, then cover them with protective bags.

Programme Fabric type max. load capacity

(kg, dry weight)

Horse blankets Horse blankets, saddle-cloths, gaiters, boots, bandages, textile

halters PT 8257 10

PT 8337 13

PT 8407 16

PT 8507 20

PT 8807 32

60°C, Dries to 0 % residual moisture, Tumble phase, Cooling down phase

Woollen horse

blankets

Horse blankets with high percentage of wool

74°C, 5 min. drying phase, Cooling down phase.

Temperatures given refer to extracted air temperature.

Dryer

Load (individual items)

Saddle cloths/

Numnahs

Summer

blankets

Winter

blankets

PT 8257 7 2 1

PT 8337 9 2 - 3 1 - 2

PT 8407 11 2 - 3 1 - 2

PT 8507 12 3 2

PT 8807 18 4 - 5 3

Programme overview

Operating data

By pressing the \"Operating data" button, the

module can be used to read or delete operating data

either before the start of a programme, or after it has

finished.

1 Cottons extra dry 0%

2 Cottons dry 0%

3 Cottons damp 20%

\FCA

After pressing the \button the following will appear

in the display:

Operating data module

Total data

Programme data e

Selection choice:

– Total data

In this option all programme data is collated and

summarised.

– Programme data

Programme data contains all the data called up

during a programme.

– Delete data

- Module (delete total data including programme

data)

- Total data (only delete total data)

- Programme data (only delete programme data)

Pressing the button again deselects the \

"Operating data" option.

If there is no more memory available in the operating

data module a message will appear after pressing

the "Start" button to say that the operating data will be

overwritten.

If you press the A"Back" button or do not press the

"Start" button within 30 seconds, the display will revert

to the way it was before starting the programme.

Total data

Operating data module

Total data

Programme data e

After selecting Total data, the following (example) will

appear in the display:

Operating data module ~Total data

Total time power on: 200,987 h

Operating hours: 123456 h e

Other options:

Total time power on: 200,987 h

Operating hours: 123,456 h

Duration heating active: 123,456 h

Duration drive motor active: 93,456 h

Programme starts: 23,456

Programme stops: 567

Programme cancellations: 67

Amount of laundry: 1,234,567 kg

Energy: 12,345,678 kWh

Programme data

Operating data module

Programme data

Delete data e

After selecting Programme data the following

(example) will appear in the display:

Operating data module~Programme data

1 Cottons extra dry 0 %

2 Cottons dry 0 % e

Select the programme you want from the list and

press the rotary dial to call up a list of all programme

starts including date and start time for that

programme (Cottons extra dry in the example).

Programme data ~1 Cottons extra dry

Date: 21.05.2009 Start time: 11:30

Date: 21.05.2009 Start time: 12:30 e

Select the required programme start from the list for

programme 1 Cottons extra dry and confirm your

choice by pressing the rotary dial.

Programme data ~1 Cottons extra dry

Date: 21.05.2009 Start time: 11:30

Name: Smith e

Optional modules

Other options:

Town: Abingdon

Serial number: 12345678

Machine type: PT 8337

Load size: 13 kg

+ Button: Activated

Programme start: 11:30

Programme finished: 12:05

Total operating time:0h35min

Electrical energy: 12.5 kWh

Gas energy: 0 kWh

Steam energy: 0 kWh

Programme change: 2 (after making your selection and

pressing the rotary dial only the last 3 stops and starts will

be displayed.)

Programme fault: None (only the last 3 faults are saved.)

Area 1: Drying

Block1: Pre-drying

Process type: Residual moisture

Value: 15 %

Actual residual moisture: 15 %

Duration: 6 min

Max. exhaust temperature: 72 °C

Max. air intake temperature: 122 °C

Area1: Drying

Block2: Drying

Process type: Residual moisture

Value: 0 %

Actual residual moisture: 0 %

Duration: 6 min

Max. exhaust temperature: 78 °C

Max. air intake temperature: 138 °C

Area2: Cooling down

Block: Cooling down

Process type: Cooling down

Value: 50 %

Actual temperature: 50 °C

Duration: 3 min

Max. exhaust temperature: 52 °C

Max. air intake temperature: 95 °C

Residual moisture: -3 %

Delete data

Operating data module

Programme data

Delete data e

After selecting Delete data the following message will

appear in the display:

Operating data module~Delete data

Module: 21.02.2009

Total data: 12.07.2009 e

The module menu option can be used to delete the

total data and programme data from the operating

data memory.

The total data option can only be used to delete the

total data from the operating data. The programme

data option can only be used to delete programme

data from the operating data.

After making your selection and pressing the rotary

dial you will be prompted to enter your password.

Password:____

ABCDEFGHIJKLMNOPQRSTUVWXYZ

0123456789

KSA

After keying in your password or inserting your

supervisor level key card in the reader the following

security prompt will appear in the display:

Delete operating data?

After pressing the Sbutton the data will be deleted!

Peak load cut-out

If the peak-load cut out function is activated the

heating will switch itself off and any programme

running will be stopped. The following message will

appear in the display:

1 Cottons extra dry

Prog. stopped. Peak load cut-out.

Programme will continue.

üf

Once the peak load has finished, the programme will

continue automatically as before.

If the door is opened during the peak load cut-out the

programme will have to be started again.

Optional modules

Error messages

,Repairs to electrical, gas or steam operated

machines may only be carried out by a suitably

qualified person in accordance with national and

local safety regulations. For gas heated machines

in the U.K. this must be a Gas Safe registered

technician. Repairs and other work by unqualified

persons could be dangerous. The manufacturer

cannot be held liable for unauthorised work.

Whenever the machine is switched on or the

programme list is called up the controls carry out an

analysis of the system. All modules and sensors, data

from the operating system, drying programmes and

languages are tested.

If a fault is detected in a programme or a language

the following symbol will appear in the display §.

The programme or language affected cannot be

selected.

1 Cottons extra dry 0%

2Cottons dry 0%

3 Cottons damp 20% §

Settings Back <-

Language Deutsch

English §

FC A

If a fault is found in a language that has already been

selected the following message will appear:

§Data fault

Function restricted

Language defect

A message will flash in the display if there is a

problem either before starting a programme or once it

has started:

If any of the following messages still appear after five

re-starts of the machine the following general fault

message will appear:

§System fault

Call the Service Department

if restart does not work.

The display remains dark.

There is no power to the machine.

^Check the mains switch and the on-site fuses.

§Fan fault

Programme stopped. Press the start

button. Motor overheating.

^Allow the motor to cool down.

§Machine fault

Call the Service Department

if restart does not work.

^Call the Service Department.

mDrive motor fault

Programme stopped. Press Start.

Motor overheated due to overloading.

^Allow the motor to cool down.

Problem solving guide

yPower cut

Programme stop

Press the start button.

^The programme can be continued by pressing the

"Start" button.

§Heating system fault

Programme stopped. Press the start button.

Programme will run without heating

^To continue the programme without heating press

the h"Start" button.

Call the Service Department.

§Heating system fault

Call the Service Department

if restart does not work.

^Call the Service Department.

§Pressure monitor fault

Call the Service Department

if restart does not work

^If the programme still will not start please call the

Service Department.

§Gas system fault

Call the Service Department

if restart does not work.

If this message appears after a programme has been

started:

^Open the gas tap and then press the "Start" button.

If this message appears during a programme the

pressure in the gas supply has dropped because of

other gas heated appliances operating at the same

time.

^Press the "Start" button.

^If the programme still will not start please call the

Service Department.

§Card fault

Card incorrectly inserted in card reader.

^Insert the card the right way round in the card

reader.

After sales service

In the event of any faults please contact your Dealer

or the nearest Service Department.

When contacting your Dealer or the Service

Department, please quote the Model, Serial number

(SN) and Material number (M.Nr) of your machine.

These are shown on the data plate.

This is visible above the door aperture or at the back

of the machine.

Please let the Service Department know any error

message that has appeared in the display.

Should you require spare parts ensure that you only

use genuine original Miele Spare Parts (and

remember to let the Spare Parts

Department know the model, serial number and

material number of your machine).

Problem solving guide

Fluff filter

,Do not use the machine without the fluff filter in

place. Fire risk.

A damaged fluff filter must be replaced before the

machine is used again.

Otherwise fluff and lint will cause a blockage in the

airways, the heating and the vent ducting, and the

correct functioning of the machine cannot be

assured.

The fluff filter collects any fluff and lint from the

laundry. It should be cleaned at least once a day and

whenever a reminder to clean it appears in the

display.

If there is a large amount of fluff and lint, the filter will

need frequent cleaning.

The fluff filter must not be removed. When cleaning it,

do so with care and make sure it does not get

damaged.

^Open the fluff compartment flap.

^Wipe the fluff off the filter by hand. Never use

pointed or sharp edged objects to do this.

Tumble dryer

Before any cleaning or maintenance switch the dryer

off at the on-site mains switch.

With gas heated dryers the gas connection must also

be switched off, both at the mains and at the

machine. With steam heated dryers the steam supply

cut-off valve must be closed.

,Do not use a pressure washer or hose to clean

the machine.

^The housing, control panel and any plastic

components should be cleaned using a suitable

mild cleaning agent, applied with a soft damp

cloth. Rub dry with a soft cloth after cleaning.

^If starched laundry has been dried, the drum

should be wiped out with a damp cloth afterwards.

Do not clean the machine with abrasive cleaning

agents.

After cleaning, check the seals for any damage and

make sure the door and fluff compartment flap shut

correctly.

The ventilation inlet to the dryer is located at the

back of the machine. It must not be blocked or

hindered in any way. Do not cover the machine lid

with cloths or similar items.

The area surrounding the machine, in particular

around the air inlet, must be kept free of dust and fluff

at all times. If taken into the dryer, they can cause

faults with the machine.

The following should be checked and cleaned once

a year by a Miele authorised service technician:

– The burners and burner compartment on

gas-heated dryers, the heaters and heater shaft on

electric-heated dryers.

– The entire interior of the dryer

– The fins on the exhaust fan

,To ensure the correct performance of the

machine and to prevent the risk of faults and fire, it

is important to check the machine and carry out

maintenance on a regular basis.

Cleaning and care

Levelling the machine

The dryer does not require a plinth. However, make

sure that any uneven areas of the floor are made

level.

The dryer must be perfectly level to ensure that it

functions correctly.

The screw feet Acan be adjusted to align it.

After aligning correctly you will need to use a

screwdriver to secure discs Bto the floor plate.

Installation on a raised plinth

The dryer can be installed on a raised concrete

plinth.

,If the machine is installed on an on-site plinth,

it must be secured using the fixing brackets

supplied. Otherwise there is the danger of the

machine moving and falling off the plinth.

^Secure the front feet of the dryer with the clamps

supplied.

Reducing the noise level

The dryer is fitted with an exhaust fan which can be

heard during operation.

If this noise disturbs you it is possible to fit a silencer

(available from Miele as an optional accessory) into

the dryer's exhaust duct (see "Installation

instructions).

Coin mechanism

The dryer can be fitted with a coin mechanism.*

A suitable adapter* is required for this. The machine

has to be reprogrammed by a Miele authorised

service technician.

Empty the coin box every day. This prevents too

many coins or tokens collecting in the coin box,

which could lead to the machine breaking down.

* available from your Miele Dealer or the Miele Spare

Parts Department.

Communication module XKM RS232

The dryer can fitted with a communication module

which enables it to be linked to a PC via a serial

interface.

The slot for the communication module is located on

the rear of the machine.

An editor programme is available from Miele.

Installation and connection

PT 825X EL/G PT 833X EL/G/D PT 840X EL/G/D PT 850X EL/G/D PT 880X EL/G/D

Height in mm 1400 1400 1400 1640 1640

Width in mm 906 906 906 1206 1206

Depth in mm 852 1035 1164 1018 1384

Depth with door open in

1456 1639 1768 1622 1988

Weight in kg 148/149.5 164.5/167.5/201 190.5/188.5/215.5 238/238.5/265 286/280/318

Drum volume in l 250 325 400 500 800

Max. capacity in kg

(dry laundry)

13 16 20 25 40

Voltage See data plate

Connected load See data plate

Fuse rating See data plate

Test certificates

awarded

See data plate

Max. load bearing

in operation in N

1636/1651 1857/1886/2250 2136/2143/2408 2703/2708/2968 3394/3335/3708

Product safety standard IEC 335-1, IEC 335-2-11

Emission sound

pressure level in

dB (A), EN ISO 11204

<70

Sound power level in

dB (A), EN ISO 9614-2

<80

Technical data

1 Machine type

2 Serial number

3 Article number

4 Material number

5 Voltage/Frequency

6 Control fuse

7 Drive motor

8 Drum data

9 Drum diameter/Drum depth

10 Spin speed

11 Drum volume/Laundry dry weight

12 Kinetic energy

13 Run-up time

14 Braking time

15 Heating

16 Indentification/Year of manufacture

17 Commissioning date

18 Electric heating

19 Fuse rating (on-site)

20 Indirect steam heating

21 Direct steam heating

22 Gas heating

23 Area for test certification labels

Explanation of symbols on the data plate

bopq

drs

hj v

1.Sort the laundry

Not all textiles are suitable for machine drying. Please read the instructions given on the

garment care label.

q= Dry at normal temperature

r= Dry at low temperature

s= Do not tumble dry

^Sort the laundry according to fibre type and weave

2.Switch the machine on and load the drum

^Press the "On" button Iin

^Open the drum door and load the laundry

3.Select a programme using the rotary selector

Standard programmes: 1 Cottons extra dry 0 %

2 Cottons dry 0 %

3 Cottons damp 20 %

4 Cottons damp 25 %

5 Cottons damp 40 %

6 Minimum iron dry 0 %

7 Minimum iron damp 10 %

8 Minimum iron damp 20 %

9 Woollens 5 min.

10 Delicates 20%

11 Timed drying cold air 15 min.

12 Timed drying hot air 20 min.

13 Proofing

14 Outerwear

4.Press the start button and the programme selected will commence

5.A buzzer will sound at the end of the programme

^Open the drum door and unload the laundry

6.If no more laundry is to be processed:

^Close the drum door

^Then switch the dryer off using the 0"Off" switch

^Check the fluff / lint filter and clean if necessary.

Abbreviated operating instructions PT 8257 / 8337 / 8407 / 8507 / 8807

2 Cottons dry

Programme finished

Anti-crease Ready at 12:35

mFC Kf

Gebruiksaanwijzing

Droogautomaten

PT 8257

PT 8337

PT 8407

PT 8507

PT 8807

Lees beslist de gebruiksaanwijzing voordat u het apparaat

plaatst, installeert en in gebruik neemt.

Dat is veiliger voor uzelf en u voorkomt onnodige schade aan het apparaat. M.-Nr. 07 713 432

nl-NL

Product specificaties

Merk:	Miele Professional
Categorie:	Wasdroger
Model:	PT 8337

Heb je hulp nodig?

Als je hulp nodig hebt met Miele Professional PT 8337 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasdroger Miele Professional

Miele Professional PT 8337 Handleiding

25 Augustus 2023

Miele Professional PT 8503 Handleiding

25 Augustus 2023

Miele Professional PT 8333 Handleiding

25 Augustus 2023

Miele Professional PT 8301 SL Handleiding

25 Augustus 2023

Miele Professional PT 5136 Handleiding

25 Augustus 2023

Miele Professional PT 8401 Handleiding

25 Augustus 2023

Miele Professional PT 8303 SL Handleiding

25 Augustus 2023

Miele Professional PT 5186 Handleiding

25 Augustus 2023

Miele Professional PT 7186 Vario Handleiding

25 Augustus 2023

Miele Professional PT 8331 COP Handleiding

25 Augustus 2023

Handleiding Wasdroger

Nieuwste handleidingen voor Wasdroger

Whirlpool WP C8 WBS EE Handleiding

24 Maart 2025

Whirlpool WP C10X WBS EE Handleiding

24 Maart 2025

Whirlpool WP C9 WBS EE Handleiding

24 Maart 2025

Whirlpool C WSD 74M WBS ES Handleiding

24 Maart 2025

Whirlpool C WD 104M WBS SPT Handleiding

24 Maart 2025

Pitsos WTP704D8 Handleiding

21 Maart 2025

Profilo KM8612HTR Handleiding

21 Maart 2025

Bosch WQG2420WFG Handleiding

21 Maart 2025

Whirlpool AWZ 7777 Handleiding

29 Oktober 2024

Whirlpool awz 9816 Handleiding

29 Oktober 2024