Middle Atlantic ICOMP-COOL Handleiding

Middle Atlantic Hardwarekoeling ICOMP-COOL

Lees hieronder de 📖 handleiding in het Nederlandse voor Middle Atlantic ICOMP-COOL (4 pagina's) in de categorie Hardwarekoeling. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

I-00245 Rev B

m i d d l e a t l a n t i c . c o m

THANK YOU

Thank you for purchasing the Quiet-Cool Series™ ICOMP-COOL Component Cooler.

Please read these instructions thoroughly before installing this product.

PRODUCT FEATURES

- Extends equipment life.

- Removes heat directly from the source.

- Up to ten individual ICOMP-COOLs can

be run from one power supply. 3-1/8”

[79 mm]

3-3/16”

[81 mm]

5/8” [16 mm]

SPECIFICATIONS

MODEL POWER

REQUIREMENTS CFM dBA @ 1 METER

ICOMP-COOL 7.5 VDC @ 70mA 8

Per Fan 19

ICOMP-COOL-E 7.5 VDC @ 70mA 8

Per Fan

ICOMP-COOL-3 7.5 VDC @ 210mA 8

Per Fan

- Fan turns on at 87ºF [30.5ºC] and turns off at 85ºF [29.4ºC]

- LED illuminates green when fan activates, and

red when fan deactivates

LED

Page 2

middl ea tlan tic.co m

ea t

tic .

PARTS

FAN UNIT

QTY

- ICOMP-COOL 1

- ICOMP-COOL - 3 3

- ICOMP-COOL - E 0

ADHESIVE BACKED FEET

QTY

- ICOMP-COOL 8

- ICOMP-COOL - 3 24

- ICOMP-COOL - E 8

WIRE TIE MOUNT

- ICOMP-COOL 5

- ICOMP-COOL - 3 15

- ICOMP-COOL - E 5

QTY

POWER SUPPLY

QTY

- ICOMP-COOL 1

- ICOMP-COOL - 3 1

- ICOMP-COOL - E 0

WIRE TIE

- ICOMP-COOL 5

- ICOMP-COOL - 3 15

- ICOMP-COOL - E 5

QTY

JUMPER CORD

- ICOMP-COOL 0

- ICOMP-COOL - 3 2

- ICOMP-COOL - E 1

QTY

1) Locate the hot spot on your component. (FIGURE A)

2) Clean area with provided alcohol wipe.

3) Remove paper covering adhesive ring. (FIGURE B)

4) Position ICOMP-COOL with power jack facing rear of component.

(FIGURE C) Press down to adhere.

TIP: If your cabinet does not have doors or sides, you may prefer to

position the unit so the air flows in a different direction.

5) Select appropriate wall plug for your region and install in provided

power supply.

6) Connect ICOMP-COOL to power source using provided Power

Supply.

NOTE: Wire Ties and Wire Tie Mounts are provided for cable

management.

FIGURE A

ADHESIVE

RING

FIGURE B

FIGURE C

INSTALLATION

Page 3

NOTE: If extra clearance between components is required to

accommodate the ICOMP-COOL, apply Adhesive

Backed Feet on the feet of the upper component with

adhesive side up. (FIGURE D)

Two Feet are provided for each location, but only one

per location may be required.

ADHESIVE

FOOT

FIGURE D

ICOMP-COOL-3 INSTALLATION (FIGURE E)

1) Install individual ICOMP-COOL units on equipment as required.

2) Using provided Jumper Cords, chain individual ICOMP-COOL units together.

3) Connect Power Supply to power source.

FIGURE E

ICOMP-COOL-E INSTALLATION (FIGURE F)

1) Using provided Jumper Cord,

connect ICOMP-COOL-E to

pre-installed ICOMP-COOL.

FIGURE F

Product specificaties

Merk:	Middle Atlantic
Categorie:	Hardwarekoeling
Model:	ICOMP-COOL
Kleur van het product:	Zwart
Breedte:	79 mm
Diepte:	81 mm
Hoogte:	16 mm
Gewicht verpakking:	320 g
Breedte verpakking:	101.6 mm
Diepte verpakking:	133.4 mm
Hoogte verpakking:	114.3 mm
Soort:	Koelventilator
Stroombron:	AC/DC
Duurzaamheidscertificaten:	RoHS
Aantal per verpakking:	1 stuk(s)
Ingangsspanning:	220 V
Spanning:	7.5 V
Code geharmoniseerd systeem (HS):	85389099
Stroom (max.):	0.07 A