Microchip USB3331 Handleiding

Microchip Niet gecategoriseerd USB3331

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip USB3331 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

 2013 - 2015 Microchip Technology Inc. DS00001863B-page 1

INTRODUCTION

The purpose of this application note is to provide a list of items that need to be considered when designing systems that

incorporate the following categories of Microchip USB products:

• USB 2.0 Hubs

• USB 3.1 Gen 1 Hubs

• Flash Media Controllers

• Flash Media Controller Hub Combo

• USB Transceivers

The target audience of this document is system engineers and layout professionals who are familiar with industry stan-

dard practices. This application note must be used in conjunction with the device data sheet, reference design, and other

relevant application notes.

Overview

This document includes the following chapters:

•Schematic Guidelines

•Layout Guidelines

Each chapter begins with a sub-section on the general design considerations for all products. Subsequent sub-sections

detail design considerations for specific product categories and their applications. The order of these lists are arbitrary.

References

• Application Notes:

- AN 18.16, PCB Design Guidelines for USB223x/i & USB225x/i Controllers

- AN 26.2, Implementation Guidelines for Microchip’s USB 2.0 and USB 3.1 Gen 1 Hub Devices

- AN 18.15, PCB Design Guidelines for QFN and DQFN Packages

- AN 19.17, ULPI Design Guide

- WP 2.10, PCB Design for WLCSP BGA Packages

• The data sheet for the respective product(s)

• Applicable USB specifications and ECNs available at usb.org

AN 26.21

USB Device Design Checklist

Author: Rejo Titus

Microchip Technology Inc.

AN 26.21

DS00001863B-page 2  2013 - 2015 Microchip Technology Inc.

1.0 SCHEMATIC GUIDELINES

1.1 General Considerations

□ A. Confirm the pin-out functions of the schematic symbol of the USB product matches what is provided in

the product data sheet.

□ B. For designs with exposed USB connectors, connect the USB cable shield to digital ground with an RC

network. Refer to the Microchip AN 26.2 application note for additional details.

□ C. Ensure that the power rails, such as VDD12 or VDD33, are not noisy and are stable and accurate across

all power consumption ranges. Refer to the Microchip AN 26.2 application note and the product data sheets

for additional details.

□ D. RESETn should be asserted buy a supervisory circuit when either VDD12 or VDD33 are below their

thresholds or asserted under manual or host control. Refer to the Microchip AN 26.2 application note for addi-

tional details.

□ E. To use in-system OTP programming through SMBus, SM_DAT should be pulled up with an external

resistor and SM_CLK should be pulled down with an external resistor. The programmer pulls SM_CLK up

with a resistor when connected to the PCB. Refer to the Microchip AN 26.2 application note for additional

details.

□ F. Make sure that the crystal and load capacitors are chosen correctly for proper operation. Refer to the

product data sheet for additional details.

□ G. If the Microchip product has internal regulators, place regulator capacitors on the regulator pins as

described in the product data sheet.

□ H. Internal regulators of the Microchip product must have the proper input voltage. No external voltage

should be applied to the output of these internal regulators. Refer to the product data sheet for additional

details.

□ I. Place a 2.2uF capacitor on upstream Vbus to comply with the USB-IF decoupling capacitance require-

ments with margin for capacitor tolerances. Refer to the USB 2.0 Specification for additional details.

□ J. VBUS_DET should be connected to the upstream VBUS through a resistor divider for stand-alone appli-

cations. Embedded applications should actively control this pin with a 3.3V signal. Refer to the Microchip AN

26.2 application note for additional details.

□ K. The Rbias resistor must be the correct value and have, at worst, a 1% tolerance. Refer to the product

data sheet for additional information.

□ L. Pins that are identified as no connect should not be connected to any net. Refer to the product data sheet

for additional information.

□ M. Ensure that the product is configured correctly by either puling the relevant strap pins up/down appropri-

ately, or via SMBus/I2C. Refer to the product data sheet for additional information.

FIGURE 1-1: SHIELD TO DIGITAL GROUND CONNECTION

 2013 - 2015 Microchip Technology Inc. DS00001863B-page 3

AN 26.21

□ N. Ensure that any SPI or EEPROM devices are compatible with the Microchip product. Refer to the product

data sheet for additional information.

1.1.1 USB2.0 SIGNALS

□ A. Do not use common mode chokes unless needed. Chokes must have a DIFFERENTIAL IMPEDANCE of

90 ohms. Refer to the Microchip AN 26.2 application note for additional details.

1.1.2 USB 3.1 GEN 1 SIGNALS

□ A. Do not use common mode chokes unless needed. Chokes must have a DIFFERENTIAL IMPEDANCE of

90 ohms. Refer to the Microchip AN 26.2 application note for additional details.

□ B. Do not place ESD protection ICs on SuperSpeed Tx and Rx differential pairs unless proven necessary.

Refer to the Microchip AN 26.2 application note for additional details.

1.2 USB Hubs

□ A. The PRT_PWR/PRT_CTL pins should be connected to the USB Power switch IC with an open drain

overcurrent signal when using individual port power for exposed downstream ports.

□ B. For downstream embedded devices, the appropriate PRT_PWR or PRT_CTL pin should be connected to

the input of the downstream device that controls its enumeration.

□ C. Place a 150uF capacitor on Vbus pin on any exposed downstream ports to comply with the USB-IF

requirements with margin for capacitor tolerances. Refer to USB 2.0 Specification.

1.3 Flash Media Signals

□ A. Place a capacitor on CRD_PWR pins with the appropriate value to meet the system requirements.

□ B. Ensure that the flash media card connector’s card detect and write protect switch logic are compatible

with the respective inputs to the controller. Refer to the product data sheet for additional information.

□ C. If the flash media card connector’s card detect or write protect switches are connected to the shield,

make sure that the shield is connected to ground appropriately.

Product specificaties

Merk:	Microchip
Categorie:	Niet gecategoriseerd
Model:	USB3331

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip USB3331 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Microchip

Microchip EVB-USB2504 Handleiding

17 November 2024

Microchip AT97SC3204 Handleiding

17 November 2024

Microchip ATECC608B Handleiding

16 Juli 2024

Microchip HV860 Handleiding

16 Juli 2024

Microchip EVB-LAN9255 Handleiding

16 Juli 2024

Microchip LX4580 Handleiding

16 Juli 2024

Microchip LX7720 Handleiding

16 Juli 2024

Microchip AT32UC3C0128C Handleiding

10 April 2024

Microchip AT32UC3C1512C Handleiding

10 April 2024

Microchip AT32UC3A3256 Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux IAN 071407 Handleiding

29 November 2024

Livarno Lux IAN 317128 Handleiding

29 November 2024

Livarno Lux IAN 049213 Handleiding

29 November 2024

Livarno Lux ST-1002 Handleiding

29 November 2024

Livarno Lux HG02489 Handleiding

29 November 2024

Livarno Lux HG02189 Handleiding

29 November 2024

Livarno Lux IAN 365198 Handleiding

29 November 2024

Livarno Lux IAN 367074 Handleiding

29 November 2024

Livarno Lux HG00701 Handleiding

29 November 2024

Livarno Lux IAN 337273 Handleiding

29 November 2024