Microchip PD-3501G Handleiding

Microchip Netwerkkaart/adapter PD-3501G

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip PD-3501G (4 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

11--PPoorrtt 880022..33aaff GGiiggaabbiitt PPooEE MMiiddssppaann

Notice

It is Microsemi’s policy to improve its products as new

technology, components, software, and rmware become

available. Microsemi, therefore, reserves the right to change

specications without prior notice.

Technical Support

If you encounter problems when installing or using this

product, please consult the Microsemi website at:

http://www.Microsemi.com

For technical support, call: +972-9- - 775 5123

In the USA: 1-877- -2323 480

Email: sales.support@microsemi.com

 Microsemi Corp.

Recycling and Disposal

Disposal instructions for old products. The WEEE

(Waste Electrical and Electronic Equipment)

national environmental initiatives has been put

in place to ensure that products are recycled

using best available treatment, recovery and

and recycling techniques to ensure human

health and high environmental protection. Your

product is designed and manufactured with

high quality materials and components which

can be recycled and reused. Do not dispose of

your old product in your general household

waste bin. Inform yourself about the local

separate collection system for electrical and

electronic products marked by this symbol:

Use one of the following disposal options :

1. Dispose of the complete product (including

its cables, plugs and accessories) in the

designated WEEE collection facilities.

2. If you purchase a replacement product,

return your old product (including all er

components) back to the retailer. The retailer

should accept it as required by the national

WEEE legislation.

Note: Unless otherwise noted, references to the

PD-3501G/AC in this document refer to both the PD-3501/AC

and the PD-3501G/AC.

Ordering information:

1-Port 802.3af Gigabit PoE Midspan:

o oduct Name: Microsemi Pr 3501G

o Part Number: -3501G/AC PD

1-Port 802.3af PoE Midspan

o Product Name: Microsemi 3501

o Part Number: -3501/AC PD

Document P/N: 06- -056 Rev. B00 0066

Safety Information

Important Safety Information

 The -3501G should be connected to PoE networks PD

only, without routing to the outside plant.

 Only qualied personnel can install or remove the

PD- . 3501G

 AC Power Cord Set:

 The power cord must have regulatory agency approval for

the specic country in which it is used (for example UL,

CSA, VDE, etc.).

 The power cord must be a three-conductor type (two

current carrying conductors; one ground conductor)

terminated on one end by an IEC 60320 appliance coupler

(for connection to the -3501G), and on the other end by PD

a plug containing a ground (earthing) contact.

 The power cord must be rated for a minimum of 250 VAC

RMS operation, with a minimum rated current capacity of

5 amps (or a minimum wire gauge of 18 AWG (0.75 mm2).

: A PD- installed in Australia requires power cords 3501G

with a minimum wire gauge of 16 AWG (1.0 mm2

: The - "DATA IN" and "DATA POWER OPD 3501G & UT"

ports are shielded RJ45 data sockets. They be used as cannot

Plain Old Telephone Service (POTS) telephone sockets. Only

RJ45 data connectors can be connected to these sockets.

 The AC wall socket-outlet must be near the - PD 3501G

and easily accessible. You can remove AC power from

the - by disconnecting the AC power cord from PD 3501G

either the wall socket-outlet or the - appliance PD 3501G

coupler.

 The -3501G DATA IN DATA POWER O PD and & UT

interfaces are qualied as Safety Extra-Low Voltage

(SELV) circuits according to IEC 60950-1. These

interfaces can only be connected to SELV interfaces on

other equipment.

WARNINGS!

 The -3501G should only be connected to the IP PD

device with which it was bought. Using the -3501G PD

with other IP devices can cause damage to the IP

device.

 Read the installation instructions before connecting the

PD- to its power source. 3501G

 Follow basic electricity safety measures whenever

connecting the -3501G to its power source. PD

 A voltage mismatch can cause equipment damage and

may pose a re hazard. If the voltage indicated on the

label is dierent from the power outlet voltage, do not

connect the - to this power outlet. PD 3501G

 The unit can be used only in Restricted Access

Locations.

Troubleshooting

Symptom

Corrective Steps

PD-3501G

does not

power up

1 Verify that a reliable power cord .

is used.

2 Verify that the voltage at the .

power inlet is between 100 and 240

VAC.

3 Remove and re-apply power to .

the device and check the indicators

during power up sequence.

The PD

does not

operate

1 Verify that the PD- 01G detects . 35

a PD.

2 Verify that the PD is designed for .

PoE operation.

3 Verify that you are using a .

standard Category 5/5e/6, straight-

wired cable, with four pairs.

4 If an external power splitter is in .

use, replace it with a known-good

splitter.

5 Ensure input Ethernet cable is .

connected to the DATA IN port.

6 Verify that the PD is connected .

to the Data & Power port.

7 Try to reconnect the same PD .

into a dierent -3501G. If it PD

works, there is probably a faulty port

or RJ45 connection.

8 Verify that there is no short over .

any of the twisted pair cables or

over the RJ45 connectors.

The end

device

operates,

but there

is no data

link

1 Verify that the port indicator on .

the front panel is continuously lit.

2 If an external power splitter is in .

use, replace it with a known-good

splitter.

3 Verify that for this link, you are .

using standard UTP/FTP Category 5

straight (non-crossover) cabling,

with all four pairs.

4 Verify that the Ethernet cable .

length is less than 100 meters from

the Ethernet source to the

load/remote terminal.

5 Try to reconnect the same PD .

into a dierent PD-3501G. If it

works, there is probably a faulty port

or RJ45 connection.

Port Connectivity

Indication

Ethernet

Cat . 5 Cable

Terminal

Figure 1: Connecting the -3501G PD

Indicators

Port LED

Indicated Behavior

Yellow On

Power is on (power is active)

Green On

A remote terminal is connected

Green Blinking

Overload state or short-circuit

Specications

Environmental Specications

Mode

Temperature

Humidity

Operating

0 to 40°C

32 to 104°F

10 to 90%; (no

condensation

allowed)

Storage

-20 to 70°C

-4 to 158°F

10 to 90%; (no

condensation

allowed)

Electrical Specications

Input Voltage

100-240 VAC (50/60 Hz)

Maximal Input Current

0.43 Ampere

Guaranteed Output power

15.4 Watts

Nominal Output Voltage

48VDC

Ethernet Interface

Input (DATA IN): Ethernet

10/100/1000Base-T

RJ45 female socket

Output (DATA & POWER

OUT): Ethernet

10/100/1000Base-T, plus

48VDC

RJ45 female socket, with

DC voltage on wire pairs,

4- (+) & 7-8 (- 5 ).

Functions and Features

The -3501G Power over Ethernet (PoE) is a Single Port PD

Midspan that oers a compact and cost eective power solution

for IP phones, WLAN access points, network cameras and other

IP terminal installations.

The -3501G converts AC power to VDC power is then PD 48

provided over the Ethernet cable.

The PD-3501 supports 10/100 Mbps pass through

data rates while the PD-3501G supports up to

Mbps pass through data rates .

The single port -3501G can be powered via universal PD

AC input.

PD- 01G EMC Compliance35 :

 FCC Part 15 class B and EN55022 class B

 EN55024

 VCCI

PD- 0 Safety Compliance: 35 1G

 UL/cUL per 60950-1 2

nd Ed.

 GS mark

Preliminary Steps

 Ensure that AC power is applied to the -3501GPD ,

using an operational AC cable with an appropriate

ground connection.

 Ensure that output Ethernet cable is connected to the

DATA POWER O port. & UT

 Verify that power ready Ethernet compatible device is

connected.

WARNING

Do not use cross over cable between the - output PD 3501G

port and the load device

Installation

The -3501G can be placed on a desktop. PD

: Before placing the - : PD 3501G

 Do not to cover -3501G or block the airow to the PD

PoE with any foreign objects. Keep the -3501G away PD

from excessive heat and humidity and free from

vibration and dust.

 Ensure that the cable length from Ethernet network

source to the terminal does not exceed 100 meters

(330 feet). The PoE is not a repeater and does not

amplify the Ethernet data signal.

 Use a splitter if desired; ensure that the splitter is

connected close to the terminal and not on the

PD- ! 3501G

 - -3501G into No “on off” switch exists; simply plug the PD

an AC power source.

Installing the Unit

Refer to Figure 1.

1. Connect the -3501G to an AC outlet (100 - VAC), using PD 240

a standard power cord.

2. Connect the DATA IN jack (input) to the remote Ethernet

network switch's Patch panel and the DATA & POWER OUT jack

(output) to the terminal.

Product specificaties

Merk:	Microchip
Categorie:	Netwerkkaart/adapter
Model:	PD-3501G
Kleur van het product:	Grijs
Gewicht:	350 g
Breedte:	140 mm
Diepte:	51.8 mm
Hoogte:	33.5 mm
LED-indicatoren:	Ja
AC-adapterfrequentie:	50/60 Hz
AC-adapter ingangsspanning:	100 - 240 V
Stroom:	0.43 A
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	CE, WEEE\nFCC 15, B\nEN 55032 B\nEN 55024\nVCCI
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.3af
Temperatuur bij opslag:	-20 - 70 °C
Luchtvochtigheid bij opslag:	0 - 95 procent
Ethernet interface type:	Gigabit Ethernet
Mean time between failures (MTBF):	100000 uur
Hoogte, in bedrijf:	-304.8 - 2000 m
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Aantal producten inbegrepen:	1 stuk(s)
Code geharmoniseerd systeem (HS):	85044090
Vermogen per poort Power over Ethernet (PoE):	15.4 W