Microchip MIC5301/18 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Microchip MIC5301/18 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
MIC5301/18 Evaluation Board
Single µCap ULDO™
ULDO is a trademark of Micrel, Inc
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (
408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 2007
1 M9999-030707-A
General Description
The demonstration board can be used to evaluate both the
MIC5301 and MIC5318 low dropout linear regulators. The
MIC5301 and MIC5318 are offered in fixed and adjustable
outputs. Fixed output versions add bypass pin function-
ality, allowing reduced output noise. The adjustable
version allows for the use of a resistor divider network to
adjust for the desired output voltage. The evaluation board
accommodates the fixed version.
Requirements
The MIC5301/18 requires a power supply that is able to
deliver 300mA with an input voltage range of 2.3V to 6V.
The output load can be either an active or passive load.
Circuit Description
The MIC5301/18 single Ultra Low Dropout (ULDO™)
linear regulator is easy to use. A minimum output
capacitance of 1µF is required.
An input capacitor is required when the power supply is
more than 4” away from the device. All evaluation boards
include an input capacitor within 1” of the device. This is
the minimum recommended distance from the device that
the capacitor should be placed.
The evaluation board has a 10µF ceramic on the V
IN
pin.
Although this is much larger than required for the device,
this was designed to allow for the long inductive test leads
that will be attached to the evaluation board
Data sheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
Getting Started
1. Connect an external supply to V
IN
terminal. Apply V
IN
(J3) and ground (J2 and J4) terminals of the evaluation
board, paying careful attention to polarity and supply
voltage (2.3V to 6V). Be sure to monitor the supply voltage
at the V
IN
terminal.
2. Enable the MIC5301/18. Force the enable pin (J1) high
to enable the output. Do not leave the enable pin floating.
A floating enable pin may cause an indeterminate state on
the output.
3. Connect the load to V
OUT
terminal (J5) and ground
terminals (J4 or J2). The load can be either passive
(resistor) or active (electronic load). Be sure to monitor the
output voltage at the V
OUT
terminal.
BYPEN
GND
J1
EN
MIC5301/18-x.xYMT
VIN
C1
10µF/6.3V
J2
GND
J3
VIN
J4
GND
J5
VOUT
NC
VOUT
C2
0.1µF/25V
C3
1µF/6.3V
MIC5301/18YMT Schematic
Micrel, Inc. MIC5301/18Evaluation Board
March 2007
2 M9999-030707-A
Bill of Materials
Item Part Number Manufacturer Description Qty.
C1608X5R0J106M TDK
(1)
GRM188R60J106K muRata
(2)
VJ0805G106KXYCW1BC Vishay
(3)
JMK107BJ106MA Taiyo Yuden
(4)
C1
06036D106MAT2A AVX
(5)
10µF, ceramic capacitor, 0603, 6.3V 1
C1608X5R1E104M TDK
(1)
0.1µF, ceramic capacitor, 0603, 6.3V
GRM188R61E104KA01D muRata
(2)
C2
VJ0603Y104KXX Vishay
(3)
0.1µF, ceramic capacitor, 0603, 25V 1
C1608X5R0J105M TDK
(1)
GRM188R60J105KE19D muRata
(2)
C3
VJ0603G105KXYCW1BC Vishay
(3)
1µF, ceramic capacitor, 0603, 6.3V 1
U1 MIC5301YMT or
MIC5318YMT Micrel, Inc.
(6)
ULDO with Single Output 1
Notes:
1. TDK: www.tdk.com
2. muRata: www.murata.com
3. Vishay: www.vishay.com
4. Taiyo Yuden: www. t-yuden.com
5. AVX: : www.avxcorp.com
6. Micrel, Inc.: www.micrel.com
Micrel, Inc. MIC5301/18Evaluation Board
March 2007
3 M9999-030707-A
PCB Layout
Top Layer
Bottom Layer


Product specificaties

Merk: Microchip
Categorie: Niet gecategoriseerd
Model: MIC5301/18

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip MIC5301/18 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Microchip

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd