Microchip MIC4811YMM Handleiding

Microchip Niet gecategoriseerd MIC4811YMM

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip MIC4811YMM (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
MIC4811 Evaluation Board
High Current 6 Channel Linear WLED
Driver with DAMâ„¢ and Ultra Fast
PWMâ„¢ Control
Ultra Fast PWM and DAMâ„¢ Dynamic Average Matching are trademarks of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
General Description
The MIC4811 is a high efficiency linear White LED
(WLED) driver; it is designed to drive up to six high current
WLEDs while maintaining constant current in each
channel. The MIC4811 features Dynamic Average
Matchingâ„¢ (DAMâ„¢) which is specifically designed to
provide optimum matching across all WLEDs. These high
accuracy (±1% typical) current regulated WLED channels
ensure uniform display illumination under all conditions. A
typical dropout of 100mV at 50mA is expected.
The MIC4811 is available in a 10-pin MSOP package with
a junction temperature range of -40°C to +125°C.
Datasheets and support documentation can be found on
Micrel’s web site at: www.micrel.com
Requirements
The MIC4811 evaluation board requires a power supply
that is capable of delivering at least 1A while providing an
input voltage between 3.0V and 5.5V.
Precautions
The MIC4811 evaluation board is designed for an input
voltage no greater than 6V. This evaluation board does not
have reverse polarity protection; hence, applying a
negative voltage to the VIN terminal may damage the
device.
Getting Started
1. Connect an external supply to VIN. Apply the
desired input voltage across VIN and ground
terminals, J1 and J2, respectively, paying careful
attention to polarity and supply voltage
(3.0V≤VIN≤5.5V). An ammeter may be placed
between the input supply and the VIN terminal to
the evaluation board. Ensure that the supply
voltage is monitored at the VIN terminal. The
ammeter and/or power lead resistance can reduce
the voltage supplied to the input.
2. Enable/Disable the MIC4811
To enable the device, apply a DC voltage of 1.2V or
greater to the EN pin (J3). This allows for full
brightness of the WLEDs (100% duty cycle). The EN
pin can also be used for dimming by connecting a
PWM signal and varying its duty cycle (please refer to
the Ultra Fast PWMâ„¢ Dimming Interface Section in
datasheet). Pulling EN low for more than 20ms forces
the MIC4811 into a low IQ sleep mode. Do not leave
the EN pin floating as this may cause an indeterminate
output state. A pull down resistor of 200kΩ is placed from
EN to GND to ensure that the WLEDs are OFF when an
enable signal is not applied.
3. Setting LED current with RSET resistor.
The average LED current may be calculated using the
equation below:
( )
139.0)(
820
)(
139.0
)(
820
)(
−Ω
â‹…
=
+
â‹…
=Ω
kR
D
mAI
mAI
D
kR
SET
LED
LED
SET
D is the duty cycle of the LED current during PWM
dimming; D=1 when device is fully ON. The stock
evaluation board uses an RSET value of 16.5kΩ which
corresponds to ILED of 50mA.
4. Measuring WLED current.
To measure WLED current, simply insert an ammeter
in series with the WLED(s). Keep in mind that a series
ammeter will add a small voltage drop, so the voltage
at the WLED terminal(s), D1-D6, should be used when
making dropout measurements with a series ammeter.
Ordering Information
Part Number Description
MIC4811YMM EV Evaluation board with Six Channel
WLED Driver
March 2011 M9999-032111-B
Micrel, Inc. MIC4811 Evaluation Board
March 2011 2 M9999-032111-B
MIC4811 Evaluation Board Schematic
Bill of Materials
Item Part Number Manufacturer Description Qty
C1608X5R0J225K TDK(1)
06036D225KAT2A AVX(2)
GRM188R60J225KE
19D
Murata(3)
C1
VJ0603G225KXYAT Vishay(4)
Ceramic Capacitor, 2.2µF, 6.3V, X5R, Size 0603 1
LED1– LED6 OVS5WBCR4 OPTEK Technology, Inc
(5) WLED 6
R1 CRCW060316K55F5
EA
Vishay(4) Resistor, 16.5, 1%, 1/16W, Size 0603 1
R2
CRCW06032003FKE
A Vishay(4) Resistor, 200k, 1%, 1/16W, Size 0603 1
U1 MIC4811YMM Micrel, Inc.(6) High Current 6 Channel Linear WLED Driver
with DAMâ„¢ and Ultra Fast PWMâ„¢ Control 1
Notes:
1. TDK: www.tdk.com
2. AVX: www.avx.com
3. Murata: www.murata.com
4. Vishay: www.vishay.com
5. OPTEK: www.optekinc.com
6. Micrel, Inc.: www.micrel.com
Micrel, Inc. MIC4811 Evaluation Board
March 2011 3 M9999-032111-B
PCB Layout Recommendations
Top Layer
Bottom Layer

Product specificaties

Merk: Microchip
Categorie: Niet gecategoriseerd
Model: MIC4811YMM

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip MIC4811YMM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Microchip

Microchip

Microchip EVB-USB2504 Handleiding

17 November 2024
Microchip

Microchip AT97SC3204 Handleiding

17 November 2024
Microchip

Microchip ATECC608B Handleiding

16 Juli 2024
Microchip

Microchip HV860 Handleiding

16 Juli 2024
Microchip

Microchip EVB-LAN9255 Handleiding

16 Juli 2024
Microchip

Microchip LX4580 Handleiding

16 Juli 2024
Microchip

Microchip LX7720 Handleiding

16 Juli 2024
Microchip

Microchip AT32UC3C0128C Handleiding

10 April 2024
Microchip

Microchip AT32UC3C1512C Handleiding

10 April 2024
Microchip

Microchip AT32UC3A3256 Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024