Microchip MCP41010 Handleiding

Microchip Niet gecategoriseerd MCP41010

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip MCP41010 (32 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

 2003 Microchip Technology Inc. DS11195C-page 1

MMCP41XXX/42XXX

Features

• 256 taps for each potentiometer

• Potentiometer values for 10 kΩ, 50 kΩ and

100 kΩ

• Single and dual versions

• SPI™ serial interface (mode 0,0 and 1,1)

• ±1 LSB max INL & DNL

• Low power CMOS technology

• 1 µA maximum supply current in static operation

• Multiple devices can be daisy-chained together

(MCP42XXX only)

• Shutdown feature open circuits of all resistors for

maximum power savings

• Hardware shutdown pin available on MCP42XXX

only

• Single supply operation (2.7V - 5.5V)

• Industrial temperature range: -40°C to +85°C

• Extended temperature range: -40°C to +125°C

Block Diagram

Description

The MCP41XXX and MCP42XXX devices are 256-

position, digital potentiometers available in 10 kΩ,

50 kΩ and 100 kΩ resistance versions. The

MCP41XXX is a single-channel device and is offered in

an 8-pin PDIP or SOIC package. The MCP42XXX con-

tains two independent channels in a 14-pin PDIP, SOIC

or TSSOP package. The wiper position of the

MCP41XXX/42XXX varies linearly and is controlled via

an industry-standard SPI interface. The devices con-

sume <1 µA during static operation. A software shut-

down feature is provided that disconnects the “A”

terminal from the resistor stack and simultaneously con-

nects the wiper to the “B” terminal. In addition, the dual

MCP42XXX has a SHDN pin that performs the same

function in hardware. During shutdown mode, the con-

tents of the wiper register can be changed and the

potentiometer returns from shutdown to the new value.

The wiper is reset to the mid-scale position (80h) upon

power-up. The RS (reset) pin implements a hardware

reset and also returns the wiper to mid-scale. The

MCP42XXX SPI interface includes both the SI and SO

pins, allowing daisy-chaining of multiple devices. Chan-

nel-to-channel resistance matching on the MCP42XXX

varies by less than 1%. These devices operate from a

single 2.7 - 5.5V supply and are specified over the

extended and industrial temperature ranges.

Package Types

16-Bit

Shift

VDD

VSS

SCK

RS SHDN

PB1

PA1

PW1

Resistor

Array 1*

Wiper

PB0

PW0

PA0

Resistor

Array 0

Wiper

Control

Logic

*Potentiometer P1 is only available on the dual

MCP42XXX version.

MCP42XXX

411

PDIP/SOIC/TSSOP

PB1

PA1

PW1

SHDN

PW0

PB0

PA0

SCK

VSS

VDD

MCP41XXX

PDIP/SOIC

PB0

PA0

VDD

PW0

VSS

SCK

Single/Dual Digital Potentiometer with SPI™ Interface

MCP41XXX/42XXX

DS11195C-page 2  2003 Microchip Technology Inc.

1.0 ELECTRICAL CHARACTERISTICS

DC CHARACTERISTICS: 10 kΩ VERSION

Electrical Characteristics: Unless otherwise indicated, V DD = +2.7V to 5.5V, TA = -40°C to +85°C (TSSOP devices are only specified at +25°C and

+85°C). Typical specifications represent values for V DD = 5V, VSS = 0V, VB = 0V, TA = +25°C.

Parameters Sym Min Typ Max Units Conditions

Rheostat Mode

Nominal Resistance R 8 10 12 kΩTA = +25°C (Note 1)

Rheostat Differential Non Linearity R-DNL -1 ±1/4 +1 LSB Note 2

Rheostat Integral Non Linearity R-INL -1 ±1/4 +1 LSB Note 2

Rheostat Tempco ∆RAB/∆T — 800 — ppm/°C

Wiper Resistance RW— 52 100 ΩVDD = 5.5V, IW = 1 mA, code 00h

W— 73 125 ΩVDD = 2.7V, IW = 1 mA, code 00h

Wiper Current IW-1 — +1 mA

Nominal Resistance Match ∆R/R — 0.2 1 % MCP42010 only, P0 to P1; T A = +25°C

Potentiometer Divider

Resolution N 8 — — Bits

Monotonicity N 8 — — Bits

Differential Non-Linearity DNL -1 ±1/4 +1 LSB Note 3

Integral Non-Linearity INL -1 ±1/4 +1 LSB Note 3

Voltage Divider Tempco ∆VW/∆T — 1 — ppm/°C Code 80h

Full Scale Error VWFSE -2 -0.7 0 LSB Code FFh, V DD

= 5V, see Figure 2-25

VWFSE -2 -0.7 0 LSB Code FFh, V DD

= 3V, see Figure 2-25

Zero Scale Error VWZSE 0 +0.7 +2 LSB Code 00h, V DD = 5V, see Figure 2-25

VWZSE 0 +0.7 +2 LSB Code 00h, V DD = 3V, see Figure 2-25

Resistor Terminals

Voltage Range VA,B,W 0 — VDD Note 4

Capacitance (CA or CB) — 15 — pF f = 1 MHz, Code = 80h, see Figure 2-30

Capacitance CW— 5.6 — pF f = 1 MHz, Code = 80h, see Figure 2-30

Dynamic Characteristics (All dynamic characteristics use V DD = 5V)

Bandwidth -3dB BW — 1 — MHz VB = 0V, Measured at Code 80h,

Output Load = 30 PF

Settling Time tS— 2 — µS V

A = VDD,VB = 0V, ±1% Error Band, Transition

from Code 00h to Code 80h, Output Load = 30 pF

Resistor Noise Voltage e NWB — 9 — nV/√Hz V

A = Open, Code 80h, f =1 kHz

Crosstalk CT— -95 — dB VA = VDD, VB = 0V (Note 5)

Digital Inputs/Outputs (CS , SCK, SI, SO) See Figure 2-12 for RS and SHDN pin operation

Schmitt Trigger High-Level Input Voltage V IH 0.7VDD ——V

Schmitt Trigger Low-Level Input Voltage V IL — — 0.3VDD V

Hysteresis of Schmitt Trigger Inputs VHYS — 0.05VDD —

Low-Level Output Voltage VOL — — 0.40 V IOL = 2.1 mA, V

DD = 5V

High-Level Output Voltage V OH VDD

- 0.5 — — V IOH = -400 µA, VDD = 5V

Input Leakage Current ILI -1 — +1 µA CS = V DD, VIN = VSS or VDD, includes VA SHDN=0

Pin Capacitance (All inputs/outputs) C IN

, COUT — 10 — pF VDD = 5.0V, TA = +25°C, f c = 1 MHz

Power Requirements

Operating Voltage Range V DD 2.7 — 5.5 V

Supply Current, Active IDDA — 340 500 µA VDD = 5.5V, CS = VSS , fSCK = 10 MHz,

SO = Open, Code FFh (Note 6)

Supply Current, Static IDDS — 0.01 1 µA CS, SHDN, RS = V DD = 5.5V, SO = Open (Note 6)

Power Supply Sensitivity PSS — 0.0015 0.0035 %/% VDD = 4.5V - 5.5V, VA

= 4.5V, Code 80h

PSS — 0.0015 0.0035 %/% VDD = 2.7V - 3.3V, VA

= 2.7V, Code 80h

Note 1: VAB

= V

DD , no connection on wiper.

2: Rheostat position non-linearity R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum

resistance wiper positions. R-DNL measures the relative step change from the ideal between successive tap positions. I W = 50 µA for

VDD = 3V and IW = 400 µA for VDD = 5V for 10 kΩ version. See Figure 2-26 for test circuit.

3: INL and DNL are measured at VW with the device configured in the voltage divider or potentiometer mode. V A = V

DD and VB = 0V. DNL

specification limits of ±1 LSB max are specified monotonic operating conditions. See Figure 2-25 for test circuit.

4: Resistor terminals A,B and W have no restrictions on polarity with respect to each other. Full-scale and zero-scale error were measured

using Figure 2-25.

5: Measured at VW pin where the voltage on the adjacent V W pin is swinging full-scale.

6: Supply current is independent of current through the potentiometers.

 2003 Microchip Technology Inc. DS11195C-page 3

MCP41XXX/42XXX

DC CHARACTERISTICS: 50 kΩ VERSION

Electrical Characteristics: Unless otherwise indicated, V DD = +2.7V to 5.5V, TA = -40°C to +85°C (TSSOP devices are only specified at +25°C and

+85°C). Typical specifications represent values for V DD = 5V, VSS = 0V, VB = 0V, T

A = +25°C.

Parameters Sym Min Typ Max Units Conditions

Rheostat Mode

Nominal Resistance R 35 50 65 kΩTA = +25°C (Note 1)

Rheostat Differential Non-Linearity R-DNL -1 ±1/4 +1 LSB Note 2

Rheostat Integral Non-Linearity R-INL -1 ±1/4 +1 LSB Note 2

Rheostat Tempco ∆RAB/∆T — 800 — ppm/°C

Wiper Resistance RW— 125 175 ΩVDD = 5.5V, IW = 1 mA, code 00h

W— 175 250 ΩVDD = 2.7V, IW = 1 mA, code 00h

Wiper Current IW-1 — +1 mA

Nominal Resistance Match ∆R/R — 0.2 1 % MCP42050 only, P0 to P1;T A = +25°C

Potentiometer Divider

Resolution N 8 — — Bits

Monotonicity N 8 — — Bits

Differential Non-Linearity DNL -1 ±1/4 +1 LSB Note 3

Integral Non-Linearity INL -1 ±1/4 +1 LSB Note 3

Voltage Divider Tempco ∆VW/∆T — 1 — ppm/°C Code 80h

Full-Scale Error VWFSE -1 -0.25 0 LSB Code FFh, V DD

= 5V, see Figure 2-25

VWFSE -1 -0.35 0 LSB Code FFh, V DD

= 3V, see Figure 2-25

Zero-Scale Error VWZSE 0 +0.25 +1 LSB Code 00h, V DD = 5V, see Figure 2-25

VWZSE 0 +0.35 +1 LSB Code 00h, V DD = 3V, see Figure 2-25

Resistor Terminals

Voltage Range VA,B,W 0 — VDD Note 4

Capacitance (CA or CB) — 11 — pF f =1 MHz, Code = 80h, see Figure 2-30

Capacitance CW— 5.6 — pF f =1 MHz, Code = 80h, see Figure 2-30

Dynamic Characteristics (All dynamic characteristics use V DD = 5V)

Bandwidth -3dB BW — 280 — MHz VB = 0V, Measured at Code 80h,

Output Load = 30 PF

Settling Time tS— 8 — µS V

A = VDD,VB = 0V, ±1% Error Band, Transition

from Code 00h to Code 80h, Output Load = 30 pF

Resistor Noise Voltage e NWB — 20 — nV/√Hz VA = Open, Code 80h, f =1 kHz

Crosstalk CT— -95 — dB VA = VDD, VB = 0V (Note 5)

Digital Inputs/Outputs (CS , SCK, SI, SO) See Figure 2-12 for RS and SHDN pin operation.

Schmitt Trigger High-Level Input Voltage V IH 0.7VDD ——V

Schmitt Trigger Low-Level Input Voltage V IL — — 0.3VDD V

Hysteresis of Schmitt Trigger Inputs VHYS — 0.05VDD —

Low-Level Output Voltage VOL — — 0.40 V IOL = 2.1 mA, V

DD = 5V

High-Level Output Voltage V OH VDD

- 0.5 — — V IOH = -400 µA, VDD = 5V

Input Leakage Current ILI -1 — +1 µA CS = VDD, VIN = VSS or VDD , includes V

A SHDN=0

Pin Capacitance (All inputs/outputs) C IN

, COUT — 10 — pF VDD = 5.0V, TA = +25°C, f c = 1 MHz

Power Requirements

Operating Voltage Range V DD 2.7 — 5.5 V

Supply Current, Active IDDA — 340 500 µA VDD = 5.5V, CS = VSS , fSCK = 10 MHz,

SO = Open, Code FFh (Note 6)

Supply Current, Static IDDS — 0.01 1 µA CS, SHDN, RS = V DD = 5.5V, SO = Open (Note 6)

Power Supply Sensitivity PSS — 0.0015 0.0035 %/% VDD = 4.5V - 5.5V, VA

= 4.5V, Code 80h

PSS — 0.0015 0.0035 %/% VDD = 2.7V - 3.3V, VA

= 2.7V, Code 80h

Note 1: VAB

= V

DD , no connection on wiper.

2: Rheostat position non-linearity R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum

resistance wiper positions. R-DNL measures the relative step change from the ideal between successive tap positions. I W = VDD/R for

+3V or +5V for 50 kΩ version. See Figure 2-26 for test circuit.

3: INL and DNL are measured at VW with the device configured in the voltage divider or potentiometer mode. V A = V

DD and VB = 0V. DNL

specification limits of ±1 LSB max are specified monotonic operating conditions. See Figure 2-25 for test circuit.

4: Resistor terminals A,B and W have no restrictions on polarity with respect to each other. Full-scale and zero-scale error were measured

using Figure 2-25.

5: Measured at VW pin where the voltage on the adjacent V W pin is swinging full scale.

6: Supply current is independent of current through the potentiometers.

Product specificaties

Merk:	Microchip
Categorie:	Niet gecategoriseerd
Model:	MCP41010

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip MCP41010 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Microchip

Microchip EVB-USB2504 Handleiding

17 November 2024

Microchip AT97SC3204 Handleiding

17 November 2024

Microchip ATECC608B Handleiding

16 Juli 2024

Microchip HV860 Handleiding

16 Juli 2024

Microchip EVB-LAN9255 Handleiding

16 Juli 2024

Microchip LX4580 Handleiding

16 Juli 2024

Microchip LX7720 Handleiding

16 Juli 2024

Microchip AT32UC3C0128C Handleiding

10 April 2024

Microchip AT32UC3C1512C Handleiding

10 April 2024

Microchip AT32UC3A3256 Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux IAN 071407 Handleiding

29 November 2024

Livarno Lux IAN 317128 Handleiding

29 November 2024

Livarno Lux IAN 049213 Handleiding

29 November 2024

Livarno Lux ST-1002 Handleiding

29 November 2024

Livarno Lux HG02489 Handleiding

29 November 2024

Livarno Lux HG02189 Handleiding

29 November 2024

Livarno Lux IAN 365198 Handleiding

29 November 2024

Livarno Lux IAN 367074 Handleiding

29 November 2024

Livarno Lux HG00701 Handleiding

29 November 2024

Livarno Lux IAN 337273 Handleiding

29 November 2024