Microchip EVB-USB3343 Handleiding

Microchip Niet gecategoriseerd EVB-USB3343

Lees hieronder de đź“– handleiding in het Nederlandse voor Microchip EVB-USB3343 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
SMSC EVB-USB3343 SMSC CONFIDENTIAL - USER MANUAL Revision 1.0 (05-06-13)
Copyright © 2013 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information
sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed
for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office
to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor
devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms
and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement").
The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly
sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product
failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further
testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be
obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and
company names are the trademarks of their respective holders.
The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES
ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT,
SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE
FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR
OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
EVB-USB3343 USB Transceiver
Evaluation Board User Manual
EVB-USB3343 USB Transceiver Evaluation Board User Manual
Revision 1.0 (05-06-13) 2 SMSC EVB-USB3343
SMSC CONFIDENTIAL - USER MANUAL
1 Introduction
This user manual is for the USB3343 USB Transceiver Evaluation Board (EVB) for use with the
USB3343 products with support for variable I/O voltage levels and 26MHz crystal operation.
The USB3343 features a ULPI interface to support systems with USB Host, Device, or On-the-Go
(OTG) capability.
2 Overview
The EVB-USB3343 is a Daughter Card designed to plug into a user's test system using a T&MT
connector. The card attaches to a USB link layer to create a USB Host, Device, or On-the-Go (OTG)
system. The board edge connector meets the UTMI+ Low Pin Interface (ULPI) Standard requirements
for the T&MT connector.
A link to the ULPI Working Group Page is available at www.smsc.com or may be obtained from your
local FAE. The EVB-USB3343 includes USB3343 packaged silicon and all external components
required for the USB transceiver function.
This manual describes PCB assembly PCB-7202AZ.
2.1 Supplying VBUS Voltage
In Host or OTG operation, the EVB-USB3343 must provide 5 Volts on V
BUS at the USB connector. The
EVB-USB3343 includes a switch that can drive VBUS using the 5 Volt supply that comes from pin 28
of the T&MT connector.
The VBUS switch is controlled by the DRVVBUS signal driven from the Link (T&MT connector). The
5 Volt switch is backdrive protected when in the off state. The switch does not provide protection from
reverse currents when it is on. See Section 2.9 and Section 2.10 for more information on configuring
the EVB-USB3343 for OTG and Host operation.
2.2 ULPI I/O Voltage
The USB3343 supports variable ULPI I/O voltage signaling. The ULPI I/O voltage is supplied in one
of two ways. By default, the EVB is shipped with VDDIO supplied by the on-board LDO.
Resistor R11 is used to set VDDIO, the digital logic high voltage. To change the value of VDDIO,
calculate a new value for R27 (ohms) as follows.
R11 = (VDDIO/1.225-1) x 169000
VDDIO must be in the range of 1.8 Volts - 3.3 Volts nominal.
VDDIO can also be supplied to the USB3343 from the T&MT connector instead of using the LDO. To
do this, the LDO (U10) must be removed.
The VDDIO voltage level that has been configured on the EVB-USB3343 must be the same as the
ULPI I/O voltage level that the link is using.
EVB-USB3343 USB Transceiver Evaluation Board User Manual
SMSC EVB-USB3343 3 Revision 1.0 (05-06-13)
SMSC CONFIDENTIAL - USER MANUAL
2.3 Edge Connector for Digital I/O
The T&MT edge connector is compliant to the ULPI specification. Part numbers and manufacturers for
this connector and it’s mate are given in Table 2.1.
2.4 REFCLK Frequency Selection
The EVB-USB3343 is by default configured for operation with a 26MHz crystal (Y1). The EVB also
accomodates the use of a 26MHz oscillator (X1). To use a 26MHz oscillator, X1, U6, and R4 must be
populated, and Y1, R30, and C22 must be removed.
2.5 USB Connector
A standard Mini-AB connector is provided to attach a USB cable or connector. Provision is made on
the PCB to accept a Micro-AB connector. See the bill of materials in Section 6 for connector part
numbers. Do not substitute a different part number for the Mini-AB receptacle or a short circuit of the
USB signals may result at the micro-AB connector PCB footprint.
2.6 VBUS Present Detection
The USB controller must detect VBUS when a USB cable is attached in device mode or when the USB
controller turns on VBUS in host or OTG mode. The USB connector VBUS signal is connected to the
VBUS pin of the USB3343. The USB3343 includes all of the comparators required to detect VBUS and
report the state of VBUS to the USB controller via the ULPI bus.
2.7 ULPI Signal Test Points
Probe points at location J2, provide access to all ULPI signals. Install the Tektronix logic analyzer probe
retention kit at J2 to probe these signals. Ordering information for the retention kit is provided in the
bill of materials.
2.8 Other Signal Test Points
There are five other test points located on the board for easy access. TP1 connects to the 5V supply
coming from the T&MT connector. TP2 connects to the 3.3V VDD supply coming from the T&MT
connector. TP3 connects to Ground.
2.9 Converting the EVB to an OTG System
“Out of the box”, the EVB-USB3343 is delivered as a USB Device system. To convert it to be a USB
OTG development board, the following modifications must be made:
1. Install R13 (zero ohm resistor). This connects the VBUS 5V switch to the VBUS signal.
Table 2.1 Edge Connector on the EVB-USB3343
PART NUMBER DESCRIPTION MANUFACTURER
2-557101-5 100 pin edge connector on EVB-USB3343 AMP
2-557-101-5 Mating connector to the EVB-USB3343 AMP
1-1734037-0 Alternate 100 pin edge connector for EVB-USB3343 TYCO
1-1734099-0 Alternate mating connector to the EVB-USB3343 TYCO

Product specificaties

Merk: Microchip
Categorie: Niet gecategoriseerd
Model: EVB-USB3343

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip EVB-USB3343 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Microchip

Microchip

Microchip EVB-USB2504 Handleiding

17 November 2024
Microchip

Microchip AT97SC3204 Handleiding

17 November 2024
Microchip

Microchip ATECC608B Handleiding

16 Juli 2024
Microchip

Microchip HV860 Handleiding

16 Juli 2024
Microchip

Microchip EVB-LAN9255 Handleiding

16 Juli 2024
Microchip

Microchip LX4580 Handleiding

16 Juli 2024
Microchip

Microchip LX7720 Handleiding

16 Juli 2024
Microchip

Microchip AT32UC3C0128C Handleiding

10 April 2024
Microchip

Microchip AT32UC3C1512C Handleiding

10 April 2024
Microchip

Microchip AT32UC3A3256 Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024