Microchip dsPIC33EP256MC502 Handleiding

Microchip Niet gecategoriseerd dsPIC33EP256MC502

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip dsPIC33EP256MC502 (130 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/130

High-Speed PWM

Section 14. High-Speed PWM

HIGHLIGHTS

This section of the manual contains the following major topics:

14.1 Introduction .................................................................................................................. 14-2

14.2 Features....................................................................................................................... 14-2

14.3 Control Registers ......................................................................................................... 14-3

14.4 Architecture Overview................................................................................................ 14-24

14.5 Module Description .................................................................................................... 14-27

14.6 PWM Operating Modes.............................................................................................. 14-33

14.7 PWM Generator......................................................................................................... 14-71

14.8 PWM Trigger.............................................................................................................. 14-87

14.9 PWM Interrupts.......................................................................................................... 14-98

14.10 PWM Fault Pins ......................................................................................................... 14-99

14.11 Special Features ...................................................................................................... 14-105

14.12 PWM Output Pin Control...........................................................................................14-111

14.13 Immediate Update of PWM Duty Cycle ................................................................... 14-113

14.14 Power-Saving Modes............................................................................................... 14-114

14.15 External Control of Individual Time Base(s)............................................................. 14-114

14.16 Application Information ............................................................................................ 14-115

14.17 Register Map............................................................................................................ 14-126

14.18 Related Application Notes........................................................................................ 14-127

14.19 Revision History ....................................................................................................... 14-128

dsPIC33E/PIC24E Family Reference Manual

14.1 INTRODUCTION

This section describes the High-Speed Pulse-Width Modulator (PWM) module and its

associated operational modes. The High-Speed PWM module in the dsPIC33E/PIC24E

device family supports a wide variety of PWM modes and is ideal for power

conversion/motor control applications. Some of the common applications include:

• AC-to-DC converters

• DC-to-DC converters

• AC and DC motors: BLDC, PMSM, ACIM, SRM, etc.

• Inverters

• Battery chargers

• Digital lighting

• Uninterrupted Power Supply (UPS)

• Power Factor Correction (PFC) (e.g., Interleaved PFC and Bridgeless PFC)

14.2 FEATURES

The High-Speed PWM module consists of the following major features:

• Up to seven PWM generators, each with an individual time base

• Two PWM outputs per PWM generator

• Individual period and duty cycle for each PWM output

• Duty cycle, dead time, phase shift and frequency resolution equal to the system clock

source (TOSC)

• Independent fault and current-limit inputs for up to 14 PWM outputs

• Redundant Output mode

• Independent Output mode (this feature is not available on all devices)

• Push-Pull Output mode

• Complementary Output mode

• Center-Aligned PWM mode

• Output override control

• Special Event Trigger

• PWM capture feature

• Prescaler for input clock

• ADC triggering with PWM

• Independent PWM frequency, duty cycle and phase shift changes

• Leading-Edge Blanking (LEB) functionality

• Dead time compensation

• Output clock chopping

Note: This family reference manual section is meant to serve as a complement to device

data sheets. Depending on the device variant, this manual section may not apply to

all dsPIC33E/PIC24E devices.

Please consult the note at the beginning of the “High-Speed PWM” chapter in the

current device data sheet to check whether this document supports the device you

are using.

Device data sheets and family reference manual sections are available for

download from the Microchip Worldwide Web site at: http://www.microchip.com

Section 14. High-Speed PWM

High-Speed PWM

14.3 CONTROL REGISTERS

The following registers control the operation of the High-Speed PWM module:

•PTCON: PWM Time Base Control Register

- Enables or disables the High-Speed PWM module

- Sets the Special Event Trigger for the ADC

- Enables or disables immediate period updates

- Selects the synchronizing source for the master time base

- Specifies synchronization settings

•PTCON2: PWM Clock Divider Select Register 2

Provides the clock prescaler to the PWM master time base

•PTPER: Primary Master Time Base Period Register

Provides the PWM time period value

•STCON: PWM Secondary Master Time Base Control Registe (1)

- Enables or disables immediate period updates based on the secondary master time base

- Selects the synchronization source for the secondary master time base

- Specifies the synchronization setting for secondary master time base control

• STCON2: PWM Secondary Clock Divider Select Register 2(1)

Provides the clock prescaler to the PWM secondary master time base

•STPER: Secondary Master Time Base Period Register(1)

Provides the secondary master time base period value

•MDC: PWM Master Duty Cycle Register

Provides the PWM master duty cycle value

•SEVTCMP: PWM Special Event Compare Register

Provides the compare value that is used to trigger the ADC module

•SSEVTCMP: PWM Secondary Special Event Compare Register(1)

Provides the compare value that is used to trigger the ADC module based on the

secondary master time base

•CHOP: PWM Chop Clock Generator Register

- Provides the chop clock frequency

- Enables or disables the chop clock generator

•PWMKEY: PWM Unlock Register(1)

Writes the unlock sequence to allow writes to the IOCONx and FCLCONx registers

•PWMCONx: PWM Control Register

- Enables or disables fault interrupt, current-limit interrupt and primary trigger interrupt

- Provides the interrupt status for fault interrupt, current-limit interrupt and primary trigger

interrupt

- Selects the type of time base (master time base or independent time base)

- Selects the type of duty cycle (master duty cycle or independent duty cycle)

- Controls Dead Time mode

- Enables or disables Center-Aligned mode

- Controls the external PWM Reset operation

- Enables or disables immediate updates of the duty cycle, phase offset, independent time

base period

•IOCONx: PWM I/O Control Register

- Enables or disables PWM pin control feature (PWM control or GPIO)

- Controls fault/current limit override values

- Enables PWMxH and PWMxL pin swapping

- Controls the PWMxH and PWMxL output polarity

- Controls the PWMxH and PWMxL output if any of the following modes is selected:

• Complementary mode

• Push-Pull mode

• True Independent mode

Note: Not all registers are available on all devices. Refer to the “High-Speed PWM”

chapter in the specific device data sheet for availability.

dsPIC33E/PIC24E Family Reference Manual

•FCLCONx: PWM Fault Current-Limit Control Register

- Selects the current-limit control signal source

- Selects the current-limit polarity

- Enables or disables Current-Limit mode

- Selects the fault control signal source

- Configures the fault polarity

- Enables or disables Fault mode

•PDCx: PWM Generator Duty Cycle Register(1)

- Provides the duty cycle value for the PWMxH and PWMxL outputs, if master time base is

selected

- Provides the duty cycle value for the PWMxH output, if independent time base is selected

•PHASEx: PWM Primary Phase Shift Register

- Provides the phase shift value for the PWMxH and PWMxL output, if master time base is

selected

- Provides the independent time base period for the PWMxH output, if independent time

base is selected

•SDCx: PWM Secondary Duty Cycle Register(1,2)

Provides the duty cycle value for the PWMxL output, if independent time base is selected

•SPHASEx: PWM Secondary Phase Shift Register(1,2,3)

- Provides the phase shift for the PWMxL output, if the master time base is selected

- Provides the independent time base period value for the PWMxL output, if the independent

time base is selected

•DTRx: PWM Dead Time Register

- Provides the dead time value for the PWMxH output, if positive dead time is selected

- Provides the dead time value for the PWMxL output, if negative dead time is selected

•ALTDTRx: PWM Alternate Dead Time Register

- Provides the dead time value for the PWMxL output, if positive dead time is selected

- Provides the dead time value for the PWMxH output, if negative dead time is selected

•TRIGx: PWM Primary Trigger Compare Value Register

Provides the compare value to generate the primary PWM trigger

•TRGCONx: PWM Trigger Control Register

- Enables the PWMx trigger postscaler start event

- Specifies the number of PWM cycles to skip before generating the first trigger

•LEBCONx: Leading-Edge Blanking Control Register

- Selects the rising or falling edge of the PWM output for LEB

- Enables or disables LEB for fault and current-limit inputs

•LEBDLYx: Leading-Edge Blanking Delay Register

Provides leading-edge blanking delay for the fault and current-limit inputs

•PWMCAPx: Primary PWM Time Base Capture Register

Provides the captured independent time base value when a leading edge is detected on

the current-limit input, and when LEB processing on the current-limit input signal is

completed

•AUXCONx: PWM Auxiliary Control Register

- Selects PWM state blank and chop clock sources

- Selects PWMxH and PWMxL output chopping functionality

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 U-0 R/W-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0

PTEN — PTSIDL SESTAT SEIEN EIPU(1) SYNCPOL(1) SYNCOEN(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN(1) SYNCSRC<2:0>(1) SEVTPS<3:0>(1)

bit 7 bit 0

Legend: HC = Cleared in Hardware HS = Set in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PTEN: PWM Module Enable bit

1 = PWM module is enabled

0 = PWM module is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 PTSIDL: PWM Time Base Stop in Idle Mode bit

1 = PWM time base halts in CPU Idle mode

0 = PWM time base runs in CPU Idle mode

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Special Event Interrupt is pending

0 = Special Event Interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Special Event Interrupt is enabled

0 = Special Event Interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(1)

1 = Active Period register is updated immediately

0 = Active Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit

(1)

1 = SYNCIx/SYNCO polarity is inverted (active-low)

0 = SYNCIx/SYNCO is active-high

bit 8 SYNCOEN: Primary Time Base Sync Enable bit(1)

1 = SYNCO output is enabled

0 = SYNCO output is disabled

bit 7 SYNCEN: External Time Base Synchronization Enable bit(1)

1 = External synchronization of primary time base is enabled

0 = External synchronization of primary time base is disabled

bit 6-4 SYNCSRC<2:0>: Synchronous Source Selection bits(1)

These bits select the SYNCIx or PTGOx input as the synchronous source. Refer to the “High-Speed

PWM” chapter in the specific device data sheet for availability.

bit 3-0 SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits

(1)

1111 = 1:16 postscaler generates Special Event trigger at every 16th compare match event

•

0001 = 1:2 postscaler generates Special Event trigger at every second compare match event

0000 = 1:1 postscaler generates Special Event trigger at every compare match event

Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user

application must program the period register with a value that is slightly larger than the expected period of

the external synchronization input signal.

dsPIC33E/PIC24E Family Reference Manual

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — PCLKDIV<2:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(1)

111 = Reserved

110 = Divide by 64

101 = Divide by 32

100 = Divide by 16

011 = Divide by 8

010 = Divide by 4

001 = Divide by 2

000 = Divide by 1, maximum PWM timing resolution (power-on default)

Note 1: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

PTPER<15:8>(1)

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0

PTPER<7:0>(1)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PTPER<15:0>: Primary Master Time Base (PMTMR) Period Value bits(1)

Note 1: 1 LSb = 1 Tosc. For example, 7.14 ns for 70 MIPS operation.

Section 14. High-Speed PWM

High-Speed PWM

U-0 U-0 U-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — SESTAT SEIEN EIPU(2) SYNCPOL SYNCOEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN SYNCSRC<2:0> SEVTPS<3:0>

bit 7 bit 0

Legend: HC = Cleared in Hardware HS = Set in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Secondary Special Event Interrupt is pending

0 = Secondary Special Event Interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Secondary Special Event Interrupt is enabled

0 = Secondary Special Event Interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(2)

1 = Active Secondary Period register is updated immediately

0 = Active Secondary Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit

1 = SYNCO2 output is active-low

0 = SYNCO2 output is active-high

bit 8 SYNCOEN: Secondary Master Time Base Sync Enable bit

1 = SYNCO2 output is enabled

0 = SYNCO2 output is disabled

bit 7 SYNCEN: External Secondary Master Time Base Synchronization Enable bit

1 = External synchronization of secondary time base is enabled

0 = External synchronization of secondary time base is disabled

bit 6-4 SYNCSRC<2:0>: Secondary Time Base Sync Source Selection bits

These bits select the SYNCIx or PTGOx input as the synchronous source. Refer to the “High-Speed

PWM” chapter in the specific device data sheet for availability.

bit 3-0 SEVTPS<3:0>: PWM Secondary Special Event Trigger Output Postscaler Select bits

1111 = 1:16 Postscale

•

0001 = 1:2 Postscale

0000 = 1:1 Postscale

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

2: This bit only applies to the secondary master time base period.

dsPIC33E/PIC24E Family Reference Manual

(1)

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — PCLKDIV<2:0>(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(2)

111 = Reserved

110 = Divide by 64

101 = Divide by 32

100 = Divide by 16

011 = Divide by 8

010 = Divide by 4

001 = Divide by 2

000 = Divide by 1, maximum PWM timing resolution (power-on default)

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

2: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

Section 14. High-Speed PWM

High-Speed PWM

(1)

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

STPER<15:8>

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

STPER<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STPER<15:0>: Secondary Master Time Base Period Value bits

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

MDC<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

MDC<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 MDC<15:0>: Master PWM Duty Cycle Value bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SEVTCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SEVTCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SEVTCMP<15:0>: Special Event Compare Count Value bits

dsPIC33E/PIC24E Family Reference Manual

(1)

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SSEVTCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SSEVTCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SSEVTCMP<15:0>: Secondary Special Event Compare Count Value bits

The optional SSEVTCMP register and the optional secondary master time base provide an additional

Special Event Trigger. The secondary special event trigger also has its own postscaler controlled by

the SEVTPS<3:0> bits in the STCON register.

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

R/W-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0

CHPCLKEN — — — — — CHOPCLK<9:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

CHOPCLK<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 CHPCLKEN: Enable Chop Clock Generator bit

1 = Chop clock generator is enabled

0 = Chop clock generator is disabled

bit 14-10 Unimplemented: Read as ‘0’

bit 9-0 CHOPCLK<9:0>: Chop Clock Divider bits

Chop Frequency = (FP/PLKDIV) / (CHOPCLK<9:0> + 1)

As an example, for devices running at 60 MIPS, a value of all zeros will yield a 60 MHz chop clock

(period = 16.7 ns) with the PWM clock prescaler configured for fastest clock. A value of ‘0000000001’

in the CHOPCLK<9:0> bits will yield a 30 MHz chop clock with the PWM clock prescaler configured

for fastest clock.

Note: The chop clock generator operates with the Primary PWM Clock Prescaler bits (PCLKDIV<2:0>) in the

PTCON2 register.

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PWMKEY<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PWMKEY<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PWMKEY<15:0>: PWM Unlock bits

If the PWMLOCK Configuration bit is asserted (PWMLOCK = 1), the IOCONx and FCLCONx registers

are writable only after the proper sequence is written to the PWMKEY register. If the PWMLOCK

Configuration bit is deasserted (PWMLOCK = 0), the IOCONx and FCLCONx registers are writable at

all times. Refer to 14.5.3 “Write Protection” for further details of the unlock sequence.

Note 1: This register is implemented only in devices where the PWMLOCK Configuration bit is present in the

FOSCSEL Configuration register.

dsPIC33E/PIC24E Family Reference Manual

HS/HC-0 HS/HC-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

FLTSTAT(1) CLSTAT(1) TRGSTAT FLTIEN CLIEN TRGIEN ITB(3) MDCS(3)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

DTC<1:0> DTCP(5) — MTBS CAM(2,3) XPRES(4) IUE(3)

bit 7 bit 0

Legend: HC = Cleared in Hardware HS = Set in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 FLTSTAT: Fault Interrupt Status bit(1)

1 = Fault interrupt is pending

0 = No fault interrupt is pending

This bit is cleared by setting FLTIEN = 0.

bit 14 CLSTAT: Current-Limit Interrupt Status bit(1)

1 = Current-limit interrupt is pending

0 = No current-limit interrupt is pending

This bit is cleared by setting CLIEN = 0.

bit 13 TRGSTAT: Trigger Interrupt Status bit

1 = Trigger interrupt is pending

0 = No trigger interrupt is pending

This bit is cleared by setting TRGIEN = 0.

bit 12 FLTIEN: Fault Interrupt Enable bit

1 = Fault interrupt is enabled

0 = Fault interrupt is disabled and the FLTSTAT bit is cleared

bit 11 CLIEN: Current-Limit Interrupt Enable bit

1 = Current-limit interrupt enabled

0 = Current-limit interrupt disabled and the CLSTAT bit is cleared

bit 10 TRGIEN: Trigger Interrupt Enable bit

1 = A trigger event generates an interrupt request

0 = Trigger event interrupts are disabled and the TRGSTAT bit is cleared

bit 9 ITB: Independent Time Base Mode bit

(3)

1 = PHASEx/SPHASEx registers provide time base period for this PWM generator

0 = PTPER register provides timing for this PWM generator

bit 8 Master Duty Cycle MDCS: Register Select bit(3)

1 = MDC register provides duty cycle information for this PWM generator

0 = PDCx and SDCx registers provide duty cycle information for this PWM generator

Note 1: Software must clear the interrupt status here, and in the corresponding IFS bit in the Interrupt Controller.

2: The Independent Time Base mode (ITB = 1 0) must be enabled to use Center-Aligned mode. If ITB = , the

CAM bit is ignored.

3: These bits should not be changed after the PWM is enabled (PTEN = 1).

4: To operate in External Period Reset mode, the ITB bit must be set to ‘ ’ and the CLMOD bit in the 1

FCLCONx register must be set to ‘0’.

5: For DTCP to be effective, DTC<1:0> must be set to ‘11’; otherwise, DTCP is ignored.

6: Negative dead time is only implemented for Edge-Aligned mode (CAM = 0).

Section 14. High-Speed PWM

High-Speed PWM

bit 7-6 DTC<1:0>: Dead Time Control bits

11 = Dead Time Compensation mode enabled

10 = Dead time function is disabled

01 = Negative dead time actively applied for Complementary Output mode(6)

00 = Positive dead time actively applied for all output modes

bit 5 DTCP: Dead Time Compensation Polarity bit(5)

1 = If DTCMPx pin = 0, PWMxL is shortened, and PWMxH is lengthened

If DTCMPx pin = 1, PWMxH is shortened, and PWMxL is lengthened

0 = If DTCMPx pin = 0, PWMxH is shortened, and PWMxL is lengthened

If DTCMPx pin = 1, PWMxL is shortened, and PWMxH is lengthened

bit 4 Unimplemented: Read as ‘0’

bit 3 MTBS: Master Time Base Select bit

1 = PWM generator uses the secondary master time base for synchronization and the clock source

for the PWM generation logic (if secondary time base is available)

0 = PWM generator uses the primary master time base for synchronization and the clock source for

the PWM generation logic

bit 2 CAM: Center-Aligned Mode Enable bit(2,3)

1 = Center-Aligned mode is enabled

0 = Edge-Aligned mode is enabled

bit 1 External PWM Reset Control bitXPRES: (4)

1 = Current-limit source resets primary local time base for this PWM generator if it is in Independent

Time Base mode

0 = External pins do not affect PWM time base

bit 0 IUE: Immediate Update Enable bit(3)

1 = Updates to the active MDC/PDCx/SDCx/DTRx/ALTDTRx/PHASEx/SPHASEx registers are

immediate

0 = Updates to the active MDC/PDCx/SDCx/DTRx/ALTDTRx/PHASEx/SPHASEx registers are

synchronized to the PWM time base

Note 1: Software must clear the interrupt status here, and in the corresponding IFS bit in the Interrupt Controller.

2: The Independent Time Base mode (ITB = 1 0) must be enabled to use Center-Aligned mode. If ITB = , the

CAM bit is ignored.

3: These bits should not be changed after the PWM is enabled (PTEN = 1).

4: To operate in External Period Reset mode, the ITB bit must be set to ‘ ’ and the CLMOD bit in the 1

FCLCONx register must be set to ‘0’.

5: For DTCP to be effective, DTC<1:0> must be set to ‘11’; otherwise, DTCP is ignored.

6: Negative dead time is only implemented for Edge-Aligned mode (CAM = 0).

Section 14. High-Speed PWM

High-Speed PWM

bit 5-4 FLTDAT<1:0>: State(2) for PWMxH and PWMxL Pins if FLTMOD is Enabled bits(1)

IFLTMOD (FCLCONx<15>) = 0: Normal Fault mode:

If fault is active, FLTDAT<1> provides the state for PWMxH.

If fault is active, FLTDAT<0> provides the state for PWMxL.

IFLTMOD (FCLCONx<15>) = 1: Independent Fault mode:

If current-limit is active, FLTDAT<1> provides the state for PWMxH.

If fault is active, FLTDAT<0> provides the state for PWMxL.

bit 3-2 CLDAT<1:0>: State(2) for PWMxH and PWMxL Pins if CLMOD is Enabled bits

IFLTMOD (FCLCONx<15>) = 0: Normal Fault mode:

If current-limit is active, CLDAT<1> provides the state for PWMxH.

If current-limit is active, CLDAT<0> provides the state for PWMxL.

IFLTMOD (FCLCONx<15>) = 1: Independent Fault mode:

The CLDAT<1:0> bits are ignored.

bit 1 SWAP: SWAP PWMxH and PWMxL Pins bit

1 = PWMxH output signal is connected to PWMxL pin; PWMxL output signal is connected to PWMxH

0 = PWMxH and PWMxL output signals pins are mapped to their respective pins

bit 0 OSYNC: Output Override Synchronization bit

1 = Output overrides via the OVRDAT<1:0> bits are synchronized to the PWM time base

0 = Output overrides via the OVRDAT<1:0> bits occur on next CPU clock boundary

Note 1: These bits must not be changed after the PWM module is enabled (PTEN = 1).

2: State represents Active/Inactive state of the PWM, depending on the POLH and POLL bits. For example, if

FLTDAT<1> is set to ‘1’ and POLH is set to ‘1’, the PWMxH pin will be at logic level 0 (active level) when a

fault occurs.

3: This feature is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific device

data sheet for availability.

dsPIC33E/PIC24E Family Reference Manual

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

IFLTMOD(4) CLSRC<4:0>(2,3) CLPOL(1) CLMOD

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

FLTSRC<4:0>(2,3) FLTPOL(1) FLTMOD<1:0>(4)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 IFLTMOD: Independent Fault Mode Enable bit

(4)

1 = Independent Fault mode: Current-limit input maps FLTDAT<1> to PWMxH output, and fault input

maps FLTDAT<0> to PWMxL output. The CLDAT<1:0> bits are not used for override functions.

0= Normal Fault mode: Current-limit and fault inputs map CLDAT<1:0> and FLTDAT<1:0> to PWMxH

and PWMxL outputs.

bit 14-10 CLSRC<4:0>: Current-Limit Control Signal Source Select bits for PWM Generator #

(2,3)

These bits specify the current-limit control signal source. Refer to the “High-Speed PWM” chapter of

the specific device data sheet for available selections.

bit 9 CLPOL: Current-Limit Polarity bit for PWM Generator #(1)

1 = The selected current-limit source is active-low

0 = The selected current-limit source is active-high

bit 8 CLMOD: Current-Limit Mode Enable bit for PWM Generator #

1 = Current-Limit mode is enabled

0 = Current-Limit mode is disabled

bit 7-3 FLTSRC<4:0>: Fault Control Signal Source Select bits for PWM Generator #

(2,3)

These bits specify the Fault control source. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for available selections.

bit 2 FLTPOL: Fault Polarity bit for PWM Generator #(1)

1 = The selected fault source is active-low

0 = The selected fault source is active-high

bit 1-0 FLTMOD<1:0>: Fault Mode bits for PWM Generator #(4)

11 = Fault input is disabled

10 = Reserved

01 = The selected fault source forces PWMxH, PWMxL pins to FLTDAT values (cycle)

00 = The selected fault source forces PWMxH, PWMxL pins to FLTDAT values (latched condition)

Note 1: These bits should be changed only when PTEN = 0. Changing the polarity selection during operation will

yield unpredictable results.

2: When Independent Fault mode is enabled (IFLTMOD = 1) and Fault 1 is used for Fault mode

(FLTSRC<4:0> = b0000), the Current-Limit Control Source Select bits (CLSRC<4:0>) should be set to an

unused current-limit source to prevent the current-limit source from disabling both the PWMxH and

PWMxL outputs.

3: When Independent Fault mode is enabled (IFLTMOD = 1), and Fault 1 is used for Current-Limit mode

(CLSRC<4:0> = b0000), the Fault Control Source Select bits (FLTSRC<4:0>) should be set to an unused

fault source to prevent Fault 1 from disabling both the PWMxL and PWMxH outputs.

4: This feature is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific device

data sheet for availability.

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PDCx<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PDCx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PDCx<15:0>: PWM Generator # Duty Cycle Value bits

Note 1: In Independent PWM mode, PMOD<1:0> (IOCONx<11:10>) = 11, the PDCx register controls the PWMxH

duty cycle only. In Complementary, Redundant and Push-Pull PWM modes (PMOD<1:0>

(IOCONx<11:0>) = 00 01, , or 10), the PDCx register controls the duty cycle of both the PWMxH and

PWMxL.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PHASEx<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PHASEx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PHASEx<15:0>: PWM Phase Shift Value or Independent Time Base Period bits for the PWM Generator

Note 1: If the ITB bit = 0 (PWMCONx<9>), the following applies based on the mode of operation:

• Complementary, Redundant and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00,

01 10, or ) PHASEx<15:0> = Phase shift value for PWMxH and PWMxL outputs

• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11) PHASEx<15:0> = Phase

shift value for PWMxH only

2: If the ITB bit = 1(PWMCONx<9>), the following applies based on the mode of operation:

• Complementary, Redundant, and Push-Pull Output mode (PMOD<1:0> (IOCONx<11:10>) = 00,

01 10, or ) PHASEx<15:0> = Independent time base period value for PWMxH and PWMxL

• True Independent Output mode (PMOD<1:0> (IOCONx<11:10>) = 11) PHASEx<15:0> = Independent

time base period for PWMxH only

Section 14. High-Speed PWM

High-Speed PWM

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — DTRx<13:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

DTRx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-0 DTRx<13:0>: Unsigned 14-bit Dead Time Value bits for PWMx Dead Time Unit

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — ALTDTRx<13:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ALTDTRx<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-14 Unimplemented: Read as ‘0’

bit 13-0 ALTDTRx<13:0>: Unsigned 14-bit Dead Time Value bits for PWMx Dead Time Unit

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TRGCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

TRGCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 TRGCMP<15:0>: Trigger Control Value bits

When the primary PWM functions in local time base, this register contains the compare values that

can trigger the ADC module.

dsPIC33E/PIC24E Family Reference Manual

R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0

TRGDIV<3:0> — — — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — TRGSTRT<5:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 TRGDIV<3:0>: Trigger # Output Divider bits

1111 = Trigger output for every 16th trigger event

•

0010 = Trigger output for every 3rd trigger event

0001 = Trigger output for every 2nd trigger event

0000 = Trigger output for every trigger event

bit 11-6 Unimplemented: Read as ‘0’

bit 5-0 TRGSTRT<5:0>: Trigger Postscaler Start Enable Select bits

111111 = Wait 63 PWM cycles before generating the first trigger event after the module is enabled

•

000010 = Wait 2 PWM cycles before generating the first trigger event after the module is enabled

000001 = Wait 1 PWM cycles before generating the first trigger event after the module is enabled

000000 = Wait 0 PWM cycles before generating the first trigger event after the module is enabled

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0

PHR PHF PLR PLF FLTLEBEN CLLEBEN — —

bit 15 bit 8

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— — BCH(1) BCL(1) BPHH BPHL BPLH BPLL

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PHR: PWMxH Rising Edge Trigger Enable bit

1 = Rising edge of PWMxH will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores rising edge of PWMxH

bit 14 PHF: PWMxH Falling Edge Trigger Enable bit

1 = Falling edge of PWMxH will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores falling edge of PWMxH

bit 13 PLR: PWMxL Rising Edge Trigger Enable bit

1 = Rising edge of PWMxL will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores rising edge of PWMxL

bit 12 PLF: PWMxL Falling Edge Trigger Enable bit

1 = Falling edge of PWMxL will trigger Leading-Edge Blanking counter

0 = Leading-Edge Blanking ignores falling edge of PWMxL

bit 11 FLTLEBEN: Fault Input Leading-Edge Blanking Enable bit

1 = Leading-Edge Blanking is applied to selected fault input

0 = Leading-Edge Blanking is not applied to selected fault input

bit 10 CLLEBEN: Current-Limit Leading-Edge Blanking Enable bit

1 = Leading-Edge Blanking is applied to selected current-limit input

0 = Leading-Edge Blanking is not applied to selected current-limit input

bit 9-6 Unimplemented: Read as ‘0’

bit 5 BCH: Blanking in Selected Blanking Signal High Enable bit(1)

1 = State blanking (of current-limit and/or fault input signals) when selected blanking signal is high

0 = No blanking when selected blanking signal is high

bit 4 BCL: Blanking in Selected Blanking Signal Low Enable bit

(1)

1 = State blanking (of current-limit and/or fault input signals) when selected blanking signal is low

0 = No blanking when selected blanking signal is low

bit 3 BPHH: Blanking in PWMxH High Enable bit

1 = State blanking (of current-limit and/or fault input signals) when PWMxH output is high

0 = No blanking when PWMxH output is high

bit 2 BPHL: Blanking in PWMxH Low Enable bit

1 = State blanking (of current-limit and/or fault input signals) when PWMxH output is low

0 = No blanking when PWMxH output is low

bit 1 BPLH: Blanking in PWMxL High Enable bit

1 = State blanking (of current-limit and/or fault input signals) when PWMxL output is high

0 = No blanking when PWMxL output is high

bit 0 BPLL: Blanking in PWMxL Low Enable bit

1 = State blanking (of current-limit and/or fault input signals) when PWMxL output is low

0 = No blanking when PWMxL output is low

Note 1: The blanking signal is selected via the BLANKSEL<3:0> bits (AUXCONx<11:8>).

dsPIC33E/PIC24E Family Reference Manual

U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — — LEB<11:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

LEB<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-12 Unimplemented: Read as ‘0’

bit 11-0 LEB<11:0>: Leading-Edge Blanking Delay bits for Current-Limit and Fault Inputs

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PWMCAP<15:8>(1,2)

bit 15 bit 8

R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0

PWMCAP<7:0>(1,2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PWMCAP<15:0>: Captured PWM Time Base Value bits(1,2)

The value in this register represents the captured PWM time base value when a leading edge is

detected on the current-limit input.

Note 1: The capture feature is only available on the primary output (PWMxH).

2: The feature is only active after LEB processing on the current-limit input signal is complete.

dsPIC33E/PIC24E Family Reference Manual

14.4 ARCHITECTURE OVERVIEW

Figure 14-1 illustrates the architectural overview of the High-Speed PWM module and its

interconnection with the CPU and other peripherals.

Figure 14-1: High-Speed PWM Module Architectural Overview(1)

CPU

Primary and Secondary

PWM

Generator 1

PWM

Generator 2

PWM

Generator x

PWM

Generator x

SYNCIx

SYNCOx

PWM1H

PWM1L

PWM1 Interrupt

PWM2H

PWM2L

PWM2 Interrupt

PWMxH

PWMxL

PWMx Interrupt

PWMxH

PWMxL

PWMx Interrupt

Synchronization Signal

Data Bus

ADC Module

FLTx and

Synchronization Signal

Primary Trigger

Primary Special

DTCMPx

Secondary Special

Event Trigger

Event Trigger Fault, Current-Limit

and Dead-Time Compensation

Master Time Base

Fault, Current-Limit

and Dead-Time Compensation

Fault, Current-Limit

and Dead-Time Compensation

Fault, Current-Limit

and Dead-Time Compensation

Note 1: Not all of the features and registers listed in this block diagram are available on all devices. Refer to the

“High-Speed PWM” chapter of the specific device data sheet for availability.

Section 14. High-Speed PWM

High-Speed PWM

The High-Speed PWM module contains multiple PWM generators. Each PWM generator

provides two PWM outputs: PWMxH and PWMxL. A master time base generator provides a

synchronous signal as a common time base to synchronize the various PWM outputs. Each

generator can operate independently or in sync with the master time base.

The individual PWM

outputs are available on the output pins of the device. The input fault signals and current-limit

signals, when enabled, monitor and protect the system by placing the PWM outputs into a known

“safe” state.

Each PWM generator can create a trigger to the ADC module to sample the analog signal at a

specific instance during the PWM period. In addition, the High-Speed PWM module also

generates a Special Event Trigger to the ADC module based on the master time base.

The High-Speed PWM module can synchronize itself with an external signal or can act as a

synchronizing source to any external device. The SYNCIx is the input pin, which can synchronize

the High-Speed PWM module with an external signal. The SYNCOx pin is an output pin that

provides a synchronous signal to an external device.

The High-Speed PWM module can be used for a wide variety of power conversion/motor control

applications that require:

• High operating frequencies with good resolution

• Ability to dynamically control PWM parameters such as duty cycle, period and dead time

• Ability to independently control each PWM

• Ability to synchronously control all PWMs

• Independent resource allocation for each PWM generator

• Fault handling capability

• CPU load staggering to execute multiple control loops

Each function of the High-Speed PWM module is described in detail in subsequent sections.

Figure 14-2 illustrates the interconnections between various registers in the High-Speed PWM

module.

Section 14. High-Speed PWM

High-Speed PWM

14.5 MODULE DESCRIPTION

14.5.1 PWM Clock Selection

The system clock is used to generate the clock for the High-Speed PWM module internally. The

maximum time resolution for this module is TOSC.

14.5.2 Time Base

Each PWM output in a PWM generator can use the master time base or an independent time

base. The input clock of the High-Speed PWM module has prescaler (divider) options of 1:1 to

1:64, which can be selected using the PWM Input Clock Prescaler (Divider) Select bits

(PCLKDIV<2:0>) in the PWM Clock Divider Select register (PTCON2<2:0>). The prescaled value

will also reflect the PWM resolution, which helps to reduce the power consumption of the

High-Speed PWM module. The prescaled clock is the input to the PWM clock control logic block.

The maximum clock rate provides a duty cycle and period resolution of TOSC.

For example:

• If a prescaler option of tion can be set 1:2 is selected, the PWM duty cycle and period resolu

at TOSC * 2. Thereby, the power consumption of the High-Speed PWM module would be

reduced by approximately 50 percent of the maximum speed operation.

• If a prescaler option of tion can be set 1:4 is selected, the PWM duty cycle and period resolu

at TOSC * 4. Thereby, the power consumption of the High-Speed PWM module would be

reduced by approximately 75 percent of the maximum speed operation.

The High-Speed PWM module can operate in the standard edge-aligned or center-aligned time

base.

14.5.3 Write Protection

Certain devices incorporate a write protection feature for the IOCONx and FCLCONx registers,

which prevents any inadvertent writes to these registers. This feature can be controlled by the

PWMLOCK Configuration bit (FOSCSEL<6>). The default state of the write protection feature is

enabled (PWMLOCK = 1). Refer to the “Special Features” chapter of the specific device data

sheet for more information of the Flash Configuration bytes.

To gain write access to the locked registers, the user application must write two consecutive

values of 0xABCD and 0x4321 to the PWMKEY register. The write access to the IOCONx or

FCLCONx registers must be the next SFR access following the unlock sequence; there can be

no other SFR accesses during the unlock process and subsequent write access. To write to both

the IOCONx and FCLCONx registers requires two unlock operations.

The correct unlocking sequence is described in Example 14-1.

Example 14-1: PWM Write-Protected Register Unlock Sequence

; FLT32 pin must be pulled high externally to clear and disable the fault

; Writing to FCLCON1 register requires unlock sequence

mov #0xabcd,w10 ;Load first unlock key to w10 register

mov #0x4321,w11 ;Load second unlock key to w11 register

mov #0x0000,w0 ;Load desired value of FCLCON1 register in w0

mov w10, PWMKEY ;Write first unlock key to PWMKEY register

mov w11, PWMKEY ;Write second unlock key to PWMKEY register

mov w0,FCLCON1 ;Write desired value to FCLCON1 register

; Set PWM ownership and polarity using the IOCON1 register

; Writing to IOCON1 register requires unlock sequence

mov #0xabcd,w10 ;Load first unlock key to w10 register

mov #0x4321,w11 ;Load second unlock key to w11 register

mov #0xF000,w0 ;Load desired value of IOCON1 register in w0

mov w10, PWMKEY ;Write first unlock key to PWMKEY register

mov w11, PWMKEY ;Write second unlock key to PWMKEY register

mov w0,IOCON1 ;Write desired value to IOCON1 register

dsPIC33E/PIC24E Family Reference Manual

14.5.4 Standard Edge-Aligned PWM

The standard edge-aligned PWM waveforms are illustrated in Figure 14-3. To create the

edge-aligned PWM, a timer or counter circuit counts upward from zero to a specified maximum

value, called Period. Another register contains the duty cycle value, which is constantly

compared with the timer value. When the timer or counter value is less than or equal to the duty

cycle value, the PWM output signal is asserted. When the timer value exceeds the duty cycle

value, the PWM signal is deasserted. When the timer value is greater than or equal to the period

value, the timer resets itself and the process repeats.

Figure 14-3: Standard Edge-Aligned PWM Mode

14.5.5 Center-Aligned PWM

The center-aligned PWM waveforms illustrated in Figure 14-4, align the PWM signals with

respect to a reference point so that half of the PWM signal occurs before the reference point and

the remaining half of the signal occurs after the reference point. The Center-Aligned mode is

enabled when the CAM bit (PWMCONx<2>) is set.

When operating in Center-Aligned mode, the effective PWM period is twice the value specified

in the PHASEx registers, because the independent time base counter in the PWM generator is

counting up and then counting down during the cycle. The up/down count sequence doubles the

effective PWM cycle period. This mode is used in many motor control applications.

Note: The Independent Time Base mode (ITB = 1) must be enabled to use the

Center-Aligned mode. If ITB = 0, the CAM bit is ignored.

PDC1

Period

Value

Timer

Value

Duty Cycle Match Timer Resets

Period

Duty Cycle

Period

TOFFTON

PWMxH

Section 14. High-Speed PWM

High-Speed PWM

Figure 14-4: Center-Aligned PWM Mode

Example 14-2: Edge-Aligned or Center-Aligned Mode Selection

PWM1H

PWM2H

PDC1

PDC2

PHASEx

Period

2 x Period

/* Select Edge-Aligned PWM Time Base */

PWMCON1bits.CAM = 0; /* For Edge-Aligned mode */

/* Select Center-Aligned PWM Time Base */

PWMCON1bits.CAM = 1; /* For Center-Aligned mode */

PWMCON1bits.ITB = 1; /* Must be set for Center-Aligned mode */

Section 14. High-Speed PWM

High-Speed PWM

14.6 PWM OPERATING MODES

The High-Speed PWM module supports the following operation modes:

• Push-Pull Output mode

• Complementary Output mode

• Redundant Output mode

• Independent Output mode (this feature is not available on all devices)

These operating modes can be selected using the PMOD<1:0> bits (IOCONx<11:10>).

In the following sections, figures and examples are provided, which show the PWM outputs in

multiple operating modes. Table 14-1 provides a list of the available modes and settings, with

references to the figures by number.

Table 14-1: Mode and Code Cross-reference Table

PWM Mode Mode Settings Related

Figure

Push-Pull Independent Duty Cycle and Phase, Fixed Primary Period, Edge-Aligned 14-7

Independent Duty Cycle and Phase, Fixed Secondary Period, Edge-Aligned 14-8

Master Duty Cycle and Independent Phase, Fixed Primary Period, Edge-Aligned 14-9

Master Duty Cycle and Independent Phase, Fixed Secondary Period, Edge-Aligned 14-10

Independent Duty Cycles and Periods, No Phase-Shifting, Edge-Aligned 14-11

Master Duty Cycles and Independent Periods, No Phase-Shifting, Edge-Aligned 14-12

Independent Duty Cycles and Periods, No Phase-Shifting, Center-Aligned Mode 14-13

Master Duty Cycles and Independent Periods, No Phase-Shifting, Center-Aligned Mode 14-14

Complementary Independent Duty Cycle and Phase, Fixed Primary Period, Edge-Aligned 14-15

Independent Duty Cycle and Phase, Fixed Secondary Period, Edge-Aligned 14-16

Master Duty Cycle and Independent Phase, Fixed Primary Period, Edge-Aligned 14-17

Master Duty Cycle and Independent Phase, Fixed Secondary Period, Edge-Aligned 14-18

Independent Duty Cycles and Periods, No Phase-Shifting, Edge-Aligned 14-19

Master Duty Cycles and Independent Periods, No Phase-Shifting, Edge-Aligned 14-20

Independent Duty Cycles and Periods, No Phase-Shifting, Center-Aligned 14-21

Master Duty Cycles and Independent Periods, No Phase-Shifting, Center-Aligned 14-22

Redundant Independent Duty Cycle and Phase, Fixed Primary Period, Edge-Aligned 14-23

Independent Duty Cycle and Phase, Fixed Secondary Period, Edge-Aligned 14-24

Master Duty Cycle and Variable Phase, Fixed Primary Period, Edge-Aligned 14-25

Master Duty Cycle and Variable Phase, Fixed Secondary Period, Edge-Aligned 14-26

Independent Duty Cycles and Periods, No Phase-Shifting, Edge-Aligned 14-27

Master Duty Cycles and Independent Periods, No Phase-Shifting, Edge-Aligned 14-28

Independent Duty Cycles and Periods, No Phase-Shifting, Center-Aligned 14-29

Master Duty Cycles and Independent Periods, No Phase-Shifting, Center-Aligned 14-30

Independent Independent Duty Cycle and Phase, Fixed Primary Period, Edge-Aligned 14-31

Independent Duty Cycle and Phase, Fixed Secondary Period, Edge-Aligned 14-32

Master Duty Cycle, Variable Phase, Fixed Primary Period, Edge-Aligned 14-33

Master Duty Cycle, Variable Phase, Fixed Secondary Period, Edge-Aligned 14-34

Independent Duty Cycles and Periods, No Phase-Shifting, Edge-Aligned 14-35

Master Duty Cycles, Independent Periods, No Phase-Shifting, Edge-Aligned 14-36

Independent Duty Cycles and Periods, No Phase-Shifting, Center-Aligned 14-37

Master Duty Cycles, Independent Periods, No Phase-Shifting, Center-Aligned 14-38

dsPIC33E/PIC24E Family Reference Manual

14.6.1 Push-Pull PWM Mode

In Push-Pull mode, the PWM outputs are alternately available on the PWMxH and PWMxL pins.

Some typical applications of Push-Pull mode are provided in 14.16 “Application Information”.

Figure 14-7 through Figure 14-14 and Example 14-6 through Example 14-13 show the PWM

outputs for Push-Pull PWM mode in multiple operating modes.

Figure 14-7: Push-Pull PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Note: Not all of the features and registers listed in the Figures and Code Examples in this

section are available on all devices. Refer to the “High-Speed PWM” chapter of the

specific device data sheet for availability.

PTPER

PHASE1 = 0

PHASE2

PHASE3

PDC1

Where:

PHASEx Phase of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

PTPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

PDC1

PDC2

PDC3

Complete

PWM1L Cycle

DTR1

ALTDTR1

ALTDTR2

DTR2

ALTDTR3

DTR3

Section 14. High-Speed PWM

High-Speed PWM

Example 14-6: Push-Pull PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Figure 14-8: Push-Pull PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

/* Set PWM Period on Primary Time Base */

PTPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

PDC1 = 150;

PDC2 = 200;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Push-Pull */

IOCON1 = IOCON2 = IOCON3 = 0xC800;

/* Set Primary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0000;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

Where:

PHASEx Phase of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

STPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

STPER

PHASE1 = 0

PHASE2

PHASE3

PDC1

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

PDC1

PDC2

PDC3

Complete

PWM1L Cycle

DTR1

ALTDTR1

ALTDTR2

DTR2

ALTDTR3

DTR3

dsPIC33E/PIC24E Family Reference Manual

Example 14-7: Push-Pull PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

Figure 14-9: Push-Pull PWM Mode – Master Duty Cycle and Independent Phase, Fixed Primary Period,

Edge-Aligned

/* Set PWM Period on Secondary Time Base */

STPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

PDC1 = 150;

PDC2 = 200;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Push-Pull */

IOCON1 = IOCON2 = IOCON3 = 0xC800;

/* Set Secondary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0008;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

Where:

PHASEx Phase of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

PTPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

PTPER

PHASE1 = 0

PHASE2

PHASE3

MDC

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

MDC

Complete

PWM1L Cycle

DTR1

ALTDTR1

ALTDTR2

DTR2

ALTDTR3

DTR3

Section 14. High-Speed PWM

High-Speed PWM

Example 14-8: Push-Pull PWM Mode – Master Duty Cycle and Independent Phase, Fixed Primary Period,

Edge-Aligned

Figure 14-10: Push-Pull PWM Mode – Master Duty Cycle and Independent Phase, Fixed Secondary Period,

Edge-Aligned

/* Set PWM Period on Primary Time Base*/

PTPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

MDC = 200;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Push-Pull */

IOCON1 = IOCON2 = IOCON3 = 0xC800;

/* Set Primary Time Base, Edge-Aligned Mode and Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0100;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

Where:

PHASEx Phase of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

STPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

STPER

PHASE1 = 0

PHASE2

PHASE3

MDC

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

MDC

Complete

PWM1L Cycle

DTR1

ALTDTR1

ALTDTR2

DTR2

ALTDTR3

DTR3

Section 14. High-Speed PWM

High-Speed PWM

Example 14-10: Push-Pull PWM Mode – Independent Duty Cycles and Independent Periods, No

Phase-Shifting, Edge-Aligned

Figure 14-12: Push-Pull PWM Mode – Master Duty Cycles and Independent Periods, No Phase-Shifting,

Edge-Aligned

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 1000;

PHASE2 = 900;

PHASE3 = 800;

/* Set Duty Cycles */

PDC1 = 200;

PDC2 = 300;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Push-Pull */

IOCON1 = IOCON2 = IOCON3 = 0xC800;

/* Set Independent Time Bases, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0200;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

MDC

PHASE1

PHASE2

PHASE3

Start of

PWM Cycle Complete

PWM1L Cycle

Where:

PHASEx Period of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

ALTDTR3

ALTDTR2

ALTDTR1 DTR1

DTR2

DTR3

dsPIC33E/PIC24E Family Reference Manual

Example 14-11: Push-Pull PWM Mode – Master Duty Cycles and Independent Periods, No Phase-Shifting,

Edge-Aligned

Figure 14-13: Push-Pull PWM Mode – Independent Duty Cycles and Independent Periods, No Phase-Shifting,

Center-Aligned Mode

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 1000;

PHASE2 = 900;

PHASE3 = 800;

/* Set Duty Cycles */

MDC = 200;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Push-Pull */

IOCON1 = IOCON2 = IOCON3 = 0xC800;

/* Set Independent Time Bases, Edge-Aligned Mode and Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0300;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

Start of

PWM Cycle

PHASE1

PHASE2

PHASE3

PDC1

PDC2

PDC3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Complete PWM1L

and PWM1H Cycle

Where:

PHASEx Period of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

DTRx Dead Time before PWMxH Falling Edge

ALTDTRx Dead Time before PWMxL Falling Edge

DTR1

ALTDTR1

DTR2

ALTDTR2

DTR3

ALTDTR3

PDC1

Section 14. High-Speed PWM

High-Speed PWM

14.6.2 Complementary PWM Mode

In Complementary PWM mode, the PWM output PWMxH is the complement of the PWMxL

output. Some typical applications of Complementary PWM mode are provided in

14.16 “Application Information”.

Figure 14-15 through Figure 14-22 and Example 14-14 through Example 14-21 show the PWM

outputs in multiple operating modes when the module operates in Complementary PWM mode.

Figure 14-15: Complementary PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Note: Not all of the features and registers listed in the Figures and Code Examples in this

section are available on all devices. Refer to the “High-Speed PWM” chapter of the

specific device data sheet for availability.

PTPER

PHASE1 = 0

PHASE2

PHASE3

PDC1

PDC2

PDC3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of PWM Cycle

Where: PHASEx Phase of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

PTPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

DTR1

DTR2

DTR3

ALTDTR1

ALTDTR2

ALTDTR3

dsPIC33E/PIC24E Family Reference Manual

Example 14-14: Complementary PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Figure 14-16: Complementary PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

/* Set PWM Period on Primary Time Base */

PTPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

PDC1 = 150;

PDC2 = 200;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Complementary */

IOCON1 = IOCON2 = IOCON3 = 0xC000;

/* Set Primary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0000;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

STPER

PHASE1 = 0

PHASE2

PHASE3

PDC1

PDC2

PDC3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

Where:

PHASEx Phase of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

STPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

DTR1

DTR2

DTR3

ALTDTR1

ALTDTR2

ALTDTR3

Section 14. High-Speed PWM

High-Speed PWM

Example 14-15: Complementary PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

Figure 14-17: Complementary PWM Mode – Master Duty Cycle and Independent Phase, Fixed Primary

Period, Edge-Aligned

/* Set PWM Period on Secondary Time Base */

STPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

PDC1 = 150;

PDC2 = 200;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Complementary */

IOCON1 = IOCON2 = IOCON3 = 0xC000;

/* Set Secondary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0008;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PTPER

PHASE1 = 0

PHASE2

PHASE3

MDC

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

MDC

Start of

PWM Cycle

Where:

PHASEx Phase of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

PTPER Period of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

DTR1

DTR2

DTR3

ALTDTR1

ALTDTR2

ALTDTR3

Section 14. High-Speed PWM

High-Speed PWM

Example 14-17: Complementary PWM Mode – Master Duty Cycle and Independent Phase, Fixed Secondary

Period, Edge-Aligned

Figure 14-19: Complementary PWM Mode – Independent Duty Cycles and Independent Periods, No

Phase-Shifting, Edge-Aligned

/* Set PWM Period on Secondary Time Base*/

STPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

MDC = 200;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Complementary */

IOCON1 = IOCON2 = IOCON3 = 0xC000;

/* Set Secondary Time Base, Edge-Aligned Mode and Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0108;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

PDC1

PDC2

PDC3

PHASE1

PHASE2

PHASE3

Start of

PWM Cycle

DTR1

DTR2

DTR3

ALTDTR1

ALTDTR2

ALTDTR3

Where:

PHASEx Period of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

dsPIC33E/PIC24E Family Reference Manual

Example 14-18: Complementary PWM Mode – Independent Duty Cycles and Independent Periods, No

Phase-Shifting, Edge-Aligned

Figure 14-20: Complementary PWM Mode – Master Duty Cycles and Independent Periods, No Phase-Shifting,

Edge-Aligned

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 800;

PHASE2 = 900;

PHASE3 = 1000;

/* Set Duty Cycles */

PDC1 = 200;

PDC2 = 300;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Complementary */

IOCON1 = IOCON2 = IOCON3 = 0xC000;

/* Set Independent Time Bases, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0200;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

MDC

PHASE1

PHASE2

PHASE3

Start of

PWM Cycle

DTR1

DTR2

DTR3

ALTDTR1

ALTDTR2

ALTDTR3

Where:

PHASEx Period of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

DTRx Dead Time for PWMxH Rising Edge

ALTDTRx Dead Time for PWMxL Rising Edge

Section 14. High-Speed PWM

High-Speed PWM

Example 14-19: Complementary PWM Mode – Master Duty Cycles and Independent Periods, No

Phase-Shifting, Edge-Aligned

Figure 14-21: Complementary PWM Mode – Independent Duty Cycles and Independent Periods, No

Phase-Shifting, Center-Aligned

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 800;

PHASE2 = 900;

PHASE3 = 1000;

/* Set Duty Cycles */

MDC = 200;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 25;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Complementary */

IOCON1 = IOCON2 = IOCON3 = 0xC000;

/* Set Independent Time Bases, Edge-Aligned Mode and Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0300;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PDC1

-ALTDTR1/2

PDC2

-ALTDTR2/2

PHASE1

PHASE2

PHASE3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

Complete

PWM1H and

PWM1L Cycle

ALTDTR3/2

ALTDTR2/2

ALTDTR1/2 ALTDTR1/2

Where:

PHASEx Period of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

ALTDTRx Dead time for PWMxL

ALTDTR1/2

PDC3

-ALTDTR3/2

ALTDTR1/2

ALTDTR2/2

ALTDTR3/2

Section 14. High-Speed PWM

High-Speed PWM

Example 14-21: Complementary PWM Mode – Master Duty Cycles and Independent Periods, No

Phase-Shifting, Center-Aligned

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 1000;

PHASE2 = 900;

PHASE3 = 800;

/* Set Duty Cycles */

MDC = 400;

/* Set Dead Time Values */

/* DTRx Registers are ignored in this mode */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 25;

/* Set PWM Mode to Complementary */

IOCON1 = IOCON2 = IOCON3 = 0xC000;

/* Set Independent Time Bases, Center-Aligned mode and

Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0304;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

Section 14. High-Speed PWM

High-Speed PWM

Example 14-22: Redundant PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Figure 14-24: Redundant PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

/* Set PWM Period on Primary Time Base */

PTPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

PDC1 = 150;

PDC2 = 200;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 0;

/* Set PWM Mode to Redundant */

IOCON1 = IOCON2 = IOCON3 = 0xC400;

/* Set Primary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0000;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

STPER

PHASE1 = 0

PHASE2

PHASE3

PDC1

PDC2

PDC3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

Where:

PHASEx Phase of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

STPER Period of PWMxH and PWMxL

dsPIC33E/PIC24E Family Reference Manual

Example 14-23: Redundant PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

Figure 14-25: Redundant PWM Mode – Master Duty Cycle and Variable Phase, Fixed Primary Period,

Edge-Aligned

/* Set PWM Period on Secondary Time Base */

STPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

PDC1 = 150;

PDC2 = 200;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 0;

/* Set PWM Mode to Redundant */

IOCON1 = IOCON2 = IOCON3 = 0xC400;

/* Set Secondary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0008;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PTPER

PHASE1 = 0

PHASE2

PHASE3

MDC

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

MDC

Start of

PWM Cycle

Where:

PHASEx Phase of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

PTPER Period of PWMxH and PWMxL

Section 14. High-Speed PWM

High-Speed PWM

Example 14-24: Redundant PWM Mode – Master Duty Cycle and Variable Phase, Fixed Primary Period,

Edge-Aligned

Figure 14-26: Redundant PWM Mode – Master Duty Cycle and Variable Phase, Fixed Secondary Period,

Edge-Aligned

/* Set PWM Period on Primary Time Base */

PTPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

PHASE2 = 100;

PHASE3 = 200;

/* Set Duty Cycles */

MDC = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 0;

/* Set PWM Mode to Redundant */

IOCON1 = IOCON2 = IOCON3 = 0xC400;

/* Set Primary Time Base, Edge-Aligned Mode and Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0100;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

STPER

PHASE1 = 0

PHASE2

PHASE3

MDC

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

MDC

Start of

PWM Cycle

Where:

PHASEx Phase of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

STPER Period of PWMxH and PWMxL

Section 14. High-Speed PWM

High-Speed PWM

Example 14-26: Redundant PWM Mode – Independent Duty Cycles and Independent Periods, No

Phase-Shifting, Edge-Aligned

Figure 14-28: Redundant PWM Mode – Master Duty Cycles and Independent Periods, No Phase-Shifting,

Edge-Aligned

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 800;

PHASE2 = 900;

PHASE3 = 1000;

/* Set Duty Cycles */

PDC1 = 200;

PDC2 = 300;

PDC3 = 400;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 0;

/* Set PWM Mode to Redundant */

IOCON1 = IOCON2 = IOCON3 = 0xC400;

/* Set Independent Time Bases, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0200;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

MDC

PHASE1

PHASE2

PHASE3

Start of

PWM Cycle

Where:

PHASEx Period of PWMxH and PWMxL

MDC Duty Cycle of PWMxH and PWMxL

dsPIC33E/PIC24E Family Reference Manual

Example 14-27: Redundant PWM Mode – Master Duty Cycles and Independent Periods, No Phase-Shifting,

Edge-Aligned

Figure 14-29: Redundant PWM Mode – Independent Duty Cycles and Independent Periods, No

Phase-Shifting, Center-Aligned

/* Set PWM Periods on PHASEx Registers */

PHASE1 = 800;

PHASE2 = 900;

PHASE3 = 1000;

/* Set Duty Cycles */

MDC = 200;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 0;

/* Set PWM Mode to Redundant */

IOCON1 = IOCON2 = IOCON3 = 0xC400;

/* Set Independent Time Bases, Edge-Aligned Mode and Master Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0300;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

PDC1

PDC2

PDC3

PHASE1

PHASE2

PHASE3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

Complete

PWM1H and

PWM1L Cycle

Where:

PHASEx Period of PWMxH and PWMxL

PDCx Duty Cycle of PWMxH and PWMxL

Section 14. High-Speed PWM

High-Speed PWM

14.6.4 True Independent PWM Output Mode

In True Independent PWM Output mode (PMOD = 11), the PWM outputs (PWMxH and PWMxL)

can have different duty cycles. The PDCx register specifies the duty cycle for the PWMxH output,

whereas the SDCx register specifies the duty cycle for the PWMxL output. In addition, the

PWMxH and PWMxL outputs can either have different periods or they can be phase-shifted

relative to each other.

• When ITB = 1, the PHASEx register specifies the PWM period for the PWMxH output and

the SPHASEx register specifies the PWM period for the PWMxL output

• When ITB = 0, the PHASEx register specifies the phase shift for the PWMxH output and

the SPHASEx register specifies the phase shift for the PWMxL output

Figure 14-31: Independent PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Note: Not all of the features and registers listed in the Figures and Code Examples in this

section are available on all devices. Refer to the “High-Speed PWM” chapter of the

specific device data sheet for availability.

Note: In Independent Time Base mode (ITB = 1), there may not be a deterministic phase

relationship between the PWMxH and PWMxL outputs.

PTPER

PHASE1 = 0

SPHASE1

PHASE2

SPHASE2

PHASE3

SPHASE3

PDC1

SDC1

PDC2

SDC2

PDC3

SDC3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

Where: PHASEx Phase of PWMxH

SPHASEx Phase of PWMxL

PDCx Duty Cycle of PWMxH

SDCx Duty Cycle of PWMxL

PTPER Period of PWMxH and PWMxL

dsPIC33E/PIC24E Family Reference Manual

Example 14-30: Independent PWM Mode – Independent Duty Cycle and Phase, Fixed Primary Period,

Edge-Aligned

Figure 14-32: Independent PWM Mode – Independent Duty Cycle and Phase, Fixed Secondary Period,

Edge-Aligned

/* Set PWM Period on Primary Time Base */

PTPER = 1000;

/* Set Phase Shift */

PHASE1 = 0;

SPHASE1 = 100;

PHASE2 = 200;

SPHASE2 = 300;

PHASE3 = 400;

SPHASE3 = 500;

/* Set Duty Cycles */

PDC1 = 100;

SDC1 = 200;

PDC2 = 300;

SDC2 = 400;

PDC3 = 500;

SDC3 = 600;

/* Set Dead Time Values */

DTR1 = DTR2 = DTR3 = 0;

ALTDTR1 = ALTDTR2 = ALTDTR3 = 0;

/* Set PWM Mode to Independent */

IOCON1 = IOCON2 = IOCON3 = 0xCC00;

/* Set Primary Time Base, Edge-Aligned Mode and Independent Duty Cycles */

PWMCON1 = PWMCON2 = PWMCON3 = 0x0000;

/* Configure Faults */

FCLCON1 = FCLCON2 = FCLCON3 = 0x0003;

/* 1:1 Prescaler */

PTCON2 = 0x0000;

/* Enable PWM Module */

PTCON = 0x8000;

STPER

PHASE1 = 0

SPHASE1

PHASE2

SPHASE2

PHASE3

SPHASE3

PDC1

SDC1

PDC2

SDC2

PDC3

SDC3

PWM1H

PWM1L

PWM2H

PWM2L

PWM3H

PWM3L

Start of

PWM Cycle

Where: PHASEx Phase of PWMxH

SPHASEx Phase of PWMxL

PDCx Duty Cycle of PWMxH

SDCx Duty Cycle of PWMxL

STPER Period of PWMxH and PWMxL

Section 14. High-Speed PWM

High-Speed PWM

14.7 PWM GENERATOR

This section describes the functionality of the PWM generator.

14.7.1 PWM Period

The PWM period value defines the switching frequency of the PWM pulses. The PWM period

value can be controlled by the Primary Master Time Base Period register (PTPER), or by the

Independent Time Period PHASEx and SPHASEx registers for the respective primary and

secondary PWM outputs, if available.

The PWM period value can be controlled in two ways when the High-Speed PWM module

operates in Independent Time Base mode:

• In some modes, the PHASEx register controls the PWM period value of the PWM output

signals (PWMxH and PWMxL)

• In True Independent Output mode, the PHASEx register controls the PWM period value of

the PWMxH output signal, and the SPHASEx register controls the PWM period value of the

PWMxL output signal

Refer to 14.6 “PWM Operating Modes”, for detailed information about various PWM modes and

their features.

When the High-Speed PWM module operates in Master Time Base mode, the PTPER register

holds the 16-bit value, which specifies the counting period for the PMTMR timer. When the

High-Speed PWM module operates in Independent Time Base mode, the PHASEx and

SPHASEx registers hold the 16-bit value that sp riod for the PTMRx andecifies the counting pe

STMRx timer, respectively. The timer period can be updated at any time by the user-assigned

application. The PWM time period (PTPER) in Edge-Aligned PWM mode (CAM bit

(PWMCONx<2>) is set to ‘0’) can be determined by using the Equation 14-1.

Equation 14-1: PERIOD, PHASEx and SPHASEx Register Value Calculation for

Edge-Aligned Mode

Based on Equation 14-1, while operating in the master time base (PTPER register) or the

independent time base (PHASEx and SPHASEx registers), the register value to be loaded is

shown in Example 14-38.

Example 14-38: PWM Time Period Calculation for Edge-Aligned Mode

Note: Not all registers and features listed in this section are available on all devices. Refer

to the “High-Speed PWM” chapter in the specific device data sheet for availability.

Where:

PTPER, PHASEx,

SPHASEx =

FPWM

* PWM Input Clock Prescaler

FOSC

FPWM = Desired PWM frequency

FOSC = Oscillator output (120 MHz for 60 MIPS)

PWM Input Clock Prescaler = Value defined in the PCLKDIV<2:0> bits (PTCON2<2:0)

PTPER 120MHz

20 1kHz ×

-------------------------- 6000= =

Where:

PWM Input Clock Prescaler = 1:1

System Oscillator Frequency (FOSC) = 120 MHz

Desired PWM Switching Frequency = 20 kHz

Product specificaties

Merk:	Microchip
Categorie:	Niet gecategoriseerd
Model:	dsPIC33EP256MC502

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip dsPIC33EP256MC502 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Microchip

Microchip MCP4902 Handleiding

11 Maart 2025

Microchip ATA6574 Handleiding

11 Maart 2025

Microchip mcp42010 Handleiding

25 Februari 2025

Microchip MCP47CVB04 Handleiding

25 Februari 2025

Microchip WFI32E04UC Handleiding

25 Februari 2025

Microchip mcp42050 Handleiding

25 Februari 2025

Microchip MCP47CVB14 Handleiding

25 Februari 2025

Microchip MCP48CMB08 Handleiding

25 Februari 2025

Microchip MCP47CVB28 Handleiding

25 Februari 2025

Microchip MCP48FVB18 Handleiding

25 Februari 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic Lumix DMW-AC11 Handleiding

9 April 2025

Soundstream VRN-64HBL Handleiding

9 April 2025

MOZA SR-P Handleiding

9 April 2025

Creality3D Ender-3 S1 Pro Handleiding

9 April 2025

Act AC6020 Handleiding

9 April 2025

BlueBuilt BBMA2M Handleiding

9 April 2025

Act AC6015 Handleiding

9 April 2025

Diamond Audio MSHD9813SG Handleiding

9 April 2025

Daikin ETVZ12S18EJ6V Handleiding

9 April 2025

Daikin FXFQ80AVEB Handleiding

9 April 2025