Micro Connect MC-GEN-270 Handleiding

Micro Connect Schakelaar MC-GEN-270

Lees hieronder de 📖 handleiding in het Nederlandse voor Micro Connect MC-GEN-270 (1 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 64 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

INTRODUCTION:

2 Way Speaker Switch

with Banana Connector

The product is used to distribute loudspeaker output signals from

audio amplifiers to different loudspeakers for selection and control

the volume.

This product is only approved for connection to loudspeaker outputs

of audio amplifiers and inputs of passive loudspeakers.

CONNECTION:

OPERATION:

SPECIFICATIONS:

PACKAGE CONTENTS:

● Main unit x1

● User Manual x1

1) Connect only loudspeaker outputs of audio amplifiers to the loudspeaker terminals AMP INPUT.

2) Connect only passive loudspeakers with impedance between 4 and 8 ohms to the loudspeaker terminals

SPEAKER OUTPUT.

3) Use only suitable speaker cables with a maximum cross-section of 6 mm² for cabling.

4) Carefully check the relevant operating instructions of the devices that are to be connected in regards to input and

output wiring.

5) If these instructions are not observed, the device or connected devices (amplifier or loudspeaker) may get

damaged.

6) Switch off the power switch of the amplifier before connecting it and do not switch the amplifier on again until you

have made all the necessary connections and che¬cked them. Proceed in the same way when changing the

circuit.

7) Make sure to introduce neatly the stranded wires into loudspeaker terminals to ex¬clude short circuits. Do not

remove more than 6 mm of insulation from the speaker line.

● Note the identification for connecting the loudspeaker terminals:

red = positive terminal

black = negative terminal

RIGHT = right terminal

LEFT = left terminal

● Connect loudspeaker terminals SPEAKER OUTPUT PAIR 1 and PAIR 2 to the speakers.

● Connect loudspeaker terminals AMP INPUT to the loudspeaker outputs of the amplifier.

Loudspeakers connected can be switched on individually or at the same time using the SPEAKERS selectors.

Speaker pair 1 is still running when both SPEAKERS selectors are in the OFF posi¬tion. This circuit protects your

amplifier against damage during idle operation.

● Turn on your amplifier and start the music programme you want.

● Use the SPEAKERS selectors to select the desired loudspeaker pair (PAIR 1 or PAIR 2).

Position ON > Loudspeaker pair switched on

Position OFF > Loudspeaker pair switched off

● The SPEAKER PAIR 2 VOLUME controller is used to adjust the volume of speaker pair 2.

● The overall volume is adjusted with the volume control on the amplifier.

Load.............................................. 60 W per channel

Impedance................................... 4 – 16 Ω

Cable length................................. max. 50 m

Wire cross section........................ max. 2.5 mm2

Operating conditions.................... -25 to +85 ºC, 20 – 75 % RH

Storage conditions....................... -25 to +85 ºC, 20 – 75 % RH

Product specificaties

Merk:	Micro Connect
Categorie:	Schakelaar
Model:	MC-GEN-270
Kleur van het product:	Zwart
Gewicht:	930 g
Gewicht verpakking:	1136 g
Breedte verpakking:	242 mm
Diepte verpakking:	146 mm
Hoogte verpakking:	51 mm
Aan/uitschakelaar:	Ja
Temperatuur bij opslag:	-25 - 85 °C
Luchtvochtigheid bij opslag:	20 - 75 procent
Audio-uitgangskanalen:	- kanalen
Bedrijfstemperatuur (T-T):	-25 - 85 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 75 procent
Audio invoer kanalen:	- kanalen
Synchronisatie ingangsimpedantie:	16 Ohm
Maximaal vermogen per kanaal:	60 W
Audio-uitvoerpoort(en):	8
Audio-invoerpoort(en):	4