Mercury IPS1000 Handleiding

Mercury Niet gecategoriseerd IPS1000

Lees hieronder de 📖 handleiding in het Nederlandse voor Mercury IPS1000 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 237 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

IPS300/600/1000 (12/24V)

Pure Sine Wave Inverter

User Manual

IMPORTANT NOTICE:

This product is not intended to be use by children or persons in poor health without

supervision. Please read this manual thoroughly before use.

This manual is written for below models:

652.100UK - IPS300 –12

652.101UK - IPS300- 24

652.102UK - IPS600- 12

652.103UK - IPS600- 24

652.104UK - IPS1000- 12

652.105UK - IPS1000-24

CAUTION:

Each model is design to work up to its maximum rated power load.

Please check carefully to ensure applications used are within the rated power range.

Any attempt of misuse to overload will trigger the overload protection and may cause

damage to both unit and application used. Mercury will not be responsible for any

damaged caused by misusage of the product

WARNING

Contain high voltage and high current! Do not open or

attempt to repair yourself!

User Manual

INTRODUTION:

Thank you for choosing this Pure Sine Wave Inverter. This inverter is capable of converting DC power

input to AC power output that has same output signal wave as normal domestic mains. Unlike modified

sine wave inverters, pure sine wave inverters will allow voltage sensitive or inductive equipment to work

flawlessly to it manufactured specification.

Below shows the differences in output voltage waveform between pure and modified output:

PRODUCT LAYOUT:

User Manual

FRONT PANEL:

- ON/OFF SWITCH – rocker switch to switch unit on and off

- POWER INDICATOR solid green LED indicates unit has been switched on –

- FAULT INDICATOR solid on or flashing red LED indicates fault has occurred, –

refer to fault code for interpretation

- USB POWER SOCKET 5V 1.0A USB power supply socket for charging smart phone camera etc –

- UK AC MAINS SOCKET output UK mains socket provide 230Vac 50Hz mains power –

- GROUND CONNECTION star washer and nut for ground connection to the outer case (normally –

connected to the vehicle chassis)

BACK PANEL:

- INPUT BATTERY NEGATIVE CONNECTION battery input connection to connect negative output –

of the DC power source

- INPUT BATTERY POSITIVE CONNECTIO battery input connection to connect positive output of N –

the DC power source

- FUSES location of the fuses –

- FAN DUCT fan for cooling - do not obstruct –

Temperature and load controlled multi-speed cooling fan:

The cooling fan is designed to run at a speed in proportion to the load, this minimises the running noise

and extend fan life.

- At load lower than 40% or inner temperature less than 30°C the fan will not operate

- At load between 40% - 60% the fan will operate at 40% of its maximum speed

- At load between 60% - 80% the fan will operate at 60% of its maximum speed

- At load between 80% - 100% the fan will operate at 80% of its maximum speed

- At 100% load or inner temperature exceeds 45°C the fan will operate at 100% of its maximum

speed

INSTALLATION:

Locati it is important to for the location of the inverter to meet below requirements: on –

- Dry environment where there should be no risk of the inverter coming into contact with water

- A cool shaded environment where temperature should be 0°C 40°C, –

not to be placed near any heat source and avoid direct sunlight

- A well-ventilated area, minimum clearance of two inches should be allowed in front of the

ventilation duct and fan. Please ensure free flow of air around the unit, if the unit is used to its full

load, an external fan may be used to aid the cooling of the unit

- Not to be place in the same compartment as the battery or together with flammable substances

- Avoid dusty environments, dust can cause blockage of airflow within the inverter

and cause the unit to overheat

- Avoid using long input cable run as input voltage can be affected by cable resistance and heat

Product specificaties

Merk:	Mercury
Categorie:	Niet gecategoriseerd
Model:	IPS1000

Heb je hulp nodig?

Als je hulp nodig hebt met Mercury IPS1000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Mercury

Mercury MKA 1919 Handleiding

18 Augustus 2024

Mercury TLD Handleiding

18 Augustus 2024

Mercury ST-18 Handleiding

18 Augustus 2024

Mercury CMTS01 Handleiding

18 Maart 2024

Mercury MTS01 Handleiding

18 Maart 2024

Mercury UK2US100VA Handleiding

4 Januari 2024

Mercury DC1248UK Handleiding

6 December 2023

Mercury USB-C224 Handleiding

4 September 2023

Mercury UK2US45VA Handleiding

25 Juni 2023

Mercury CB-R30 Handleiding

22 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo VPPI Handleiding

21 November 2024

Festo VAVE-P17-TP-5YL1-P Handleiding

21 November 2024

Festo SD-SUB-D-BU9 Handleiding

21 November 2024

Festo SAMH-F12-MK Handleiding

21 November 2024

Festo SFAB Handleiding

21 November 2024

Festo SFAH Handleiding

21 November 2024

Festo DRRD-12 Handleiding

21 November 2024

Festo SDE3 Handleiding

21 November 2024

Festo SFTE Handleiding

21 November 2024

Festo CRVZS-5 Handleiding

21 November 2024