Melnor 93015 Handleiding

Melnor Niet gecategoriseerd 93015

Lees hieronder de 📖 handleiding in het Nederlandse voor Melnor 93015 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Schedule “By Frequency”

Tap “Start Time” to adjust the ﬁrst watering start

time of the day and tap “OK”.

Tap “Duration” to adjust how long you want to water

and tap “OK”

Tap “Frequency” to adjust how often you want to

water and tap “OK”

The Valve is now ready to water. If using a 2 or 4 zone

Timer, complete scheduling as needed for each Valve

following the same steps.

You can return to the home screen by tapping in “<”

the upper left corner. The time until the next watering cycle will display on the

Valve setting screen.

Schedule “By Week Day”

Tap “Watering Day” to select which days you want

to water.

NOTE: The selected days will be highlighted in yellow. All

days are selected by default.

Ensure Cycle 1 is turned on. (Green)

Tap “Start Time” to adjust watering time for that

cycle. Tap “OK”.

Tap “Watering” to adjust how long you want to water.

Tap “OK”.

Watering Cycle 1 is now programmed.

To add additional watering cycles, tap “Add”. You may

set up to 12 watering cycles on each Valve.

Set "Start Time" and "Watering" as in the previous steps. Tap "OK".

If using a 2 or 4 zone Timer complete scheduling as needed for each valve

following the same steps.

You can return to the home screen by tapping in the upper left corner. “<”

The time until the next watering cycle will display on the Valve setting screen.

NOTE: You may deactivate a temporarily (Gray) and reactivate as “Cycle”

needed. Turn on (Green) to resume.

You may permanently delete a cycle by tapping the button. “Delete”

Trash icons will appear beside each cycle. Tap the trash can icon to

remove.

Manual Watering

There are two ways to turn on the water manually: Directly

from the timer through the app or .

Manual watering from the app:

Tap on the you want to control. Timer

Tap on the Valve that you want to open manually.

Set “Manual” to turn on (green) the valve. The water

will begin to run.

Tap the time to adjust how long you want to water. Tap

“OK” to set. This will become your new default manual

watering time.

The app will show the remaining manual watering

duration.

You can cancel Manual Watering at any time by setting

“Manual” to off (Gray)

Manual watering from the Timer:

Press the yellow button on the Timer above the Valve you want to use.

The Valve will open for the last manual watering time

set in the app. (Default factory setting is 20 minutes)

To stop the water at any time, press the yellow button

above the Valve again.

NOTE: You can turn the water on using the app and off

from the Valve or vice versa.

93015, 93100, 93280

1, 2 & 4 Zone Bluetooth® Water Timers

An easy and convenient way to manage your lawn and garden watering.

This instruction guide is a universal manual for Melnor 1, 2 and 4 Zone

Bluetooth® Water Timers.

User Instructions English

93XXX_INS_ENG_01

Instruction Update

We recommend you download the latest version of these instructions at:

www.melnor.com/btupdate

This is: Revision 01

Battery Installation & Assembly

Remove the battery holder from the back of the Timer. Insert 4× AA Alkaline

batteries. Replace the battery holder, making sure that

it is ﬁrmly and securely placed in the Timer.

NOTE: Once batteries are in place in the Timer, a green

light will ﬂash twice.

Attach the Timer to an outside faucet and turn water

on slowly. The water must be left on while the Timer is

attached to the faucet for your Timer to operate.

NOTE: Replace batteries when Timer battery indicator

ﬂashes a red light or when the battery icon in the app turns red. Please

use only Alkaline batteries. Do not use rechargeable batteries.

Download Melnor BT App

Compatible with Bluetooth® 4.0 devices

(minimum required iOS 9 or Android V7.0).

Download and install the app from the Melnor BT

Google Play or Apple Store.

Visit the Google Play Store Apple App Store or

and search for or scan the QR code to Melnor BT

download the app.

Make sure Bluetooth® is activated on your smart

phone or tablet.

After the app is installed, tap to launch the app.

NOTE: Your phone must be within 30 feet of the timer to operate the device.

Automatic Watering

Open the Melnor BT app.

Tap or the Timer photo to go to the Valve screen.

Tap or image on the Valve you want to schedule.

Tap “Program On/Off” to on. (Green)

Tap “Watering Mode” to set the scheduling “By

Frequency” Setting” or “By Week Day”. Tap “ to

conﬁrm.

NOTE: Scheduling “By Frequency” waters at regular

intervals.

i.e., Every 12 Hours, Every Day, Every 2 Days.

Scheduling “By Week Day” allows you to select

speciﬁc days to water.

i.e., Monday—Wednesday—Friday;

Sunday—Wednesday; Tuesday only.

7 Delay Watering

If there is rain in the forecast, you can skip watering for a period of time.

From the Valve screen select the valve you want to delay.

Activate the delay by tapping the switch on (green) “Watering Delay”

Once the “Watering Delay” is on (green)you can adjust the duration by tapping

the delay period.

Select the amount of time you want to pause the watering schedule and tap

“OK”.

NOTE: You must set Watering Delay separately for each Valve.

Eco Mode

Eco Mode is an optional setting that creates a 1 minute

pause for every 3 minutes of watering. This allows the

water to soak in the soil and reduce water run-off.

Open the app.Melnor BT Timer

Enter the Valve you want to create Eco Mode on.

In the Valve Setting screen turn on Eco Mode by

tapping “Water Saving Eco”.

You may choose to alter the Eco Mode values by

tapping and changing the preset Watering and Pause

times.

The Eco mode setting will apply to all cycles on that Valve.

Set a password

For security you can create a password for your

device to protect it from unauthorized users. The

password will be required for any user to access the

Timer.

To create a password Tap the pencil icon, then

“Change Password” and tap “OK".

Enter a four-character password and tap conﬁrm. You

can use numbers, letters, or both.

To reset your password, remove the batteries from

the Valve Unit. Reinsert the batteries while holding

down the button on Valve 1 until the battery indicator

turns red, then release. The unit is now reset.

NOTE: There is no default password. If you forget your password you will need to

reset the device, this will reset all saved setting as well.

Customizing Melnor BT App

Customizing your Device

You can customize the Timer’s name and image as it appears in your app.

Tap pencil icon on the screen.

Tap “Change Photo” to replace the default image with a new one and tap

“OK”.

Use an existing photo

To use an existing image on your smart device, tap “Albums” and tap

“OK”.

Tap which image you want to use and tap “Choose”.

To revert to the original preset image, tap Pre-Set Photo and tap “OK”.

Take a new photo

To take a new photo, tap camera and tap “OK".

Your device camera will open. Take the photo you want and tap “Use

Photo".

Change the device name

Change the name of your Bluetooth® Timer to easily identify where you are

watering or distinguish between multiple timers.

To change the device name, tap and tap “Change Name” “OK”.

Enter the desired name (max 12 characters) and tap “OK”.

Customizing Valves

You can customize the name and image of each Valve in your app to easily

identify where you are watering.

Use an existing photo

To use an existing image on your smart device, tap “Albums” and tap

“OK”.

Tap which image you want to use, and it will load into place.

To revert to the original preset image, tap Pre-Set Photo and tap “OK”.

Take a new photo

To take a new photo, tap camera and then tap “OK”.

Your device camera will open. Take the photo you want, and tap save.

Change the Valve/Valves name

To change the device name, tap and tap “Change Name” “OK”.

Enter the desired name (max 12 characters) and tap “OK”.

Additional Information

Freezing temperatures can cause water to freeze and expand, damaging the

Valve Unit. At the end of the season or when there is frost in the forecast,

remove your timer from the faucet, remove the batteries and be sure to store

the timer indoors, away from freezing temperatures.

When attaching the Valve Unit to the faucet, be sure to turn the water on

slowly.

FCC ID: VAF-93B1

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

Caution: Any changes or modiﬁcations not expressly approved by Melnor® could void the user’s

authority to operate the equipment. Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the

equipment of and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

To comply with FCC RF exposure requirements, the device and the antenna for this device must be

installed to ensure a minimum separation of 20cm or more from a person’s body. Other operating

conﬁgurations should be avoided.

CAN ICES-3 (B)/NMB-3(B) Canada Statement (ISED Statement)

ISED Certiﬁcation Number: 7111A-93B1

Model: 93015, 93100, 93280

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the

following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and

compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and

compliance.

Range: 30 ft. (10 meters) without interference

Pressure Operating: 10 - 120 PSI

Temperature Operating: 32 - 110° F (0 - 45° C)

Frequency Band: 2402 - 2480 MHz

Operating Frequency: 915MHz

Max Power: < 20 dBm

Melnor, Inc.

109 Tyson Drive

Winchester, VA 22603, USA

Product specificaties

Merk:	Melnor
Categorie:	Niet gecategoriseerd
Model:	93015
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	317.51 g
Breedte:	139.7 mm
Diepte:	60.96 mm
Hoogte:	139.7 mm
LED-indicatoren:	Ja
Ondersteund aantal accu's/batterijen:	4
Timermodi:	Handmatige bewatering
Bedrijfstemperatuur (T-T):	0 - 45 °C
Type product:	Digitale besproeiingsbesturing
Batterijtechnologie:	Alkaline
Type batterij:	AA
Lichtsensor:	Nee
Aantal bewateringen per dag:	12