Meliconi Goal Plus Handleiding

Meliconi Afstandsbediening Goal Plus

Lees hieronder de 📖 handleiding in het Nederlandse voor Meliconi Goal Plus (1 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

1. Make sure that the TV is ON.

2. Hold down the and

keys simultaneously until the light indicator at the top starts to ﬂ ash

indicating that the remote control is in programming mode.

3. Press key four times then point the remote control at the appliance.

Press and release the key slowly several times.

STOP when your TV goes OFF.

4. When your TV is OFF, press the and keys simultaneously. When

you release the keys, three ﬂ ashes indicate that the search operation

has been completed correctly.

Additional check

Check that all 7 keys are operating correctly.

If the commands work incorrectly or erratically,

you have probably entered a code for a similar

but different remote control.

In this case, repeat the search

procedure from point 2 until

all keys respond correctly to

the commands sent.

If you have any queries about :Speedy Goal Plus

• read this booklet carefully – this will help you to solve

almost all problems

• consult our Internet site to www.meliconi.com

answer all your queries more easily and quickly.

WARRANTY: 2 years

The warranty ceases to be valid if the product

is tampered with or used incorrectly.

Remote control model Speedy Goal Plus

Purchase date___________________

Identify and take note of the TV code which you have searched for,

following the code noting procedure

(see “PROGRAMMED CODE NOTING” section).

PROGRAMMED CODE NOTING

When you have programmed Speedy Goal Plus

Meliconi, note down the code on the label

in the battery compartment cover.

To ﬁ nd the code for your remote control:

1. Hold down the and keys simultaneously

until the light indicator at the top starts to ﬂ ash

indicating that the remote control is searching for

the code.

2. Release the keys and, within 12 seconds,

press and simultaneously.

3. Release and and pay attention to the

ﬂ ashing of the LED: a long ﬂ ash corresponds to a +

while a short ﬂ ash corresponds to a - .

Note the sequence of the

9 ﬂ ashes

and note them

down on the label in the battery compartment cover,

from left to right.

RE-PROGRAMMING YOUR REMOTE CONTROL BY

ENTERING THE CODE NOTED DOWN

If the remote control is no longer programmed because it has

been left without batteries for a long time or has ﬂ at batteries, you

can re-program it quickly as follows:

1. Hold down the and keys simultaneously until the light

indicator at the top starts to ﬂ ash indicating that the remote control is

programming.

2. Release the keys and, within 12 seconds, using the

and keys, enter the nine-sign code which you noted down

before. At the end,

three ﬂ ashes

indicate that the code has been saved

correctly. If not, try the code entry procedure again from .point 1

USING YOUR REMOTE CONTROL

Once you have programmed , you can turn ON your Speedy Goal Plus

TV in three ways:

• Press or .

• Press .

• Press and simultaneously: this sends the code for programme 1.

To return to programme 1 directly, press and simultaneously.

TROUBLESHOOTING

PROBLEM

The TV does not

respond and the

light indicator does

not light up when

you press a key.

The TV does not

respond but the

light indicator does

light up.

The TV does

not respond and

the light indicator

ﬂ ashes.

Not all remote

control commands

are working

correcting.

The and

keys do not select

the programmes.

SOLUTION

1. Check that the

batteries are ﬁ tted

correctly. If neces-

sary, replace them

with 2 new 1.5 V

AAA/LR03 alkaline

batteries.

2. Check that the

batteries are new

and that the remote

control is pointing

at the appliance

without any ob-

stacles in the way.

If required, reset

the remote control

code by repeating

the programming

procedure.

3. Batteries are low.

Replace them.

4. You may have

used the wrong

code. Reset the

remote control

code, following

the programming

procedure.

5. The original

remote control may

not have had this

function. In this

case, set the code

(press ) 9 times

as described in the

PROGRAMMING

YOUR REMOTE

CONTROL section

above.

INFO LINE

Agent’s stamp

NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY. THE LIGHT INDICATOR

STOPS FLASHING AND YOUR REMOTE CONTROL LEAVES PROGRAMMING MODE IN THE FOLLOWING CASES:

• if no keys are pressed for 12 seconds • if you press keys other than those indicated

• if the code search list is completed. In this case, visit www.meliconi.com

Thank you

for choosing Meliconi.

This simpliﬁ ed universal remote control contains all the main functions of most

TV remote controls on the market.

Insert the batteries and program your remote control before using it.

The remote control

requires 2 new AAA/LR03

alkaline batteries.

Insert the batteries

as shown:

FITTING THE BATTERIES

• Batteries must be changed once a year.

• Change the batteries if the light indicator starts to ﬂ ash during use. The

batteries are low.

• When removing batteries, insert the new ones within 5 minutes or you may

have to reprogram your remote control.

• Make a note of the code for your TV on the adhesive label supplied inside

the battery compartment cover. This note will be handy if you have to

reprogram your remote control.

To use the remote control with your appliances, you must ﬁ rst program Speedy Goal Plus as described below.

You can also visit our Internet site www.meliconi.com to have access to interactive instructions for easier and faster

remote control programming.

PROGRAMMING YOUR REMOTE CONTROL

Keep your Instructions Booklet for future reference.

USING THE KEYS AND FUNCTIONS

Control the

volume using +.

Control the

volume using -.

To select an

external terminal.

Mute key.

To select the next

programme or to turn

ON your TV.

Press them together

to turn ON your TV

on . programme 1

To select the previous

programme or

to turn ON your TV.

ON/OFF to turn OFF

your TV and,

in some cases,

to turn ON your TV.

SET-UP

Read these instructions carefully before programming your remote control!

IF YOU DO NOT HAVE THE PROGRAMME SELECTION KEYS ON YOUR

ORIGINAL REMOTE CONTROL

If your remote control does not have the programme selection keys

(e.g. / , +/-, CH+/-..etc) once you have programmed

Speedy Goal Plus, you can still select the programmes from 0 to 9, as

follows:

• Hold down the and keys simultaneously until the light

indicator starts to ﬂ ash indicating that the remote control is

in programming mode.

• Release the keys and press within 12 9 times

seconds.

Three ﬂ ashes

indicate that the operation has

been completed correctly.

• Make sure you can change programmes

from 0 to 9 using the and keys.

If not, repeat the search operation,

starting from point 2.

Product specificaties

Merk:	Meliconi
Categorie:	Afstandsbediening
Model:	Goal Plus
Kleur van het product:	Black, White
Ingebouwd display:	Nee
Gewicht:	- g
Maximumbereik:	- m
Input type:	Drukknopen
juiste gebruik afstandsbediening:	TV
Number of devices supported:	1