Meliconi Control TV Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Meliconi Control TV (9 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
Thank you for choosing Meliconi.
The spare CONTROL TV remote control contains all the main functions
of most TV remote controls of the brands listed on the back of the pack.
Keep your Instructions and Code Booklet for future reference.
USING THE KEYS AND FUNCTIONS
The functions described above are only operative
if your appliance also has them.
GB Use
Used to access additional
commands and to program
the remote control.
TV ON/OFF key.
Number keys.
Confirm key.
Control the volume using
+/-. These
key
s can also be
used to move to the right
and left in the MENU.
To select the next (P+) or
previous (P-) channel or
program. These keys can
also be used to move up
and down in the MENU.
To select an external
terminal. Mute
key
.
User customisation
key
s for memorising
and accessing additional
commands.
Light indicator.
Additional functions.
Fastext functions
or access to the brightness
and colour controls directly
or using the SHIFT key.
Teletext keys:
to access Teletext
to close Teletext and
return to normal viewing
Teletext page hold function
additional Teletext function.
To access your MENU.
Move within the MENU
using the +/- and P +/-
keys or SHIFT
with +/- P +/- depending
on the model of your original
remote control.
SET-UP
Read these instructions
carefully before programming
your remote control!
BRAND SEARCH PROGRAMMING MODE
A
1.Make sure that the TV is ON.
2.In the code book enclosed, look for
the brand of your TV and make a note
of the code indicated at the side
(e.g. Philips 001) or the code for the
brand indicated by the arrow.
3.Hold down the SHIFT and ON/OFF
keys together until the light indicator at
the top starts to flash indicating that
the remote control is in programming
mode.
4.Release the keys,
within 15 seconds, enter the brand
code previously identified (e.g. 001).
The light indicator flashes
more quickly to indicate
that the remote control
is ready for the search.
5.Point the remote control at the TV.
Press and release slowly one of
the most frequently-used
keys several times STOPPING
when the appliance responds
correctly to the command.
6.When the TV responds correctly,
press SHIFT to confirm.
Three flashes indicate that the
operation has been completed
correctly.
Additional check
Check that some of the other functions
used on your original remote control are
working correctly. If the commands
function incorrectly or erratically, you
have probably entered a code for a
similar but different remote control.
In this case, repeat the search
procedure from point 3.
Identify and make a note of the TV
code which you have searched for,
following the code noting procedure
(see “NOTING THE PROGRAMMED
CODE” section).
0
0
1
NOTE: THE LIGHT INDICATOR
STOPS FLASHING.
The remote control leaves the
programming mode and the light
indicator stops flashing:
•if no keys are pressed for 15 seconds
•if an invalid brand code is entered
•if the code search list is completed.
In this case, go back to point 3 or
switch to programming mode C.
FITTING THE BATTERIES
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries.
Insert the batteries as shown.
•The batteries must be changed once a year.
•Change the batteries if the light indicator starts to
flash during use, this indicates that the batteries are
low and should be changed.
•When you remove the batteries, fit the new ones
within 5 minutes or you may have to reprogram your
remote control.
•Make a note of the code for your TV on the adhesive
label inside the battery cover. This note will be
handy if you have to reprogram your control.
To program the CONTROL TV remote
control, follow the indications
in section A , Bor C.
1.Make sure that the TV is ON.
2.In the code book enclosed,
look for the brand of your TV
and make a note of the first
code indicated BENEATH
the brand previously identified
(e.g. Philips TV 075).
3.Hold down the SHIFT
and ON/OFF keys together
until the light indicator at the top
starts to flash indicating that the
remote control is in programming
mode.
4.Release the keys and press the
numeric key 8 once. Within
the next 15 seconds, key in the three
figure code you noted previously
(e.g. 075).
Three flashes indicate that the code
has been saved correctly. If not, try
the code entry procedure again from
point 3.
Additional check
Point the remote control at the TV.
Check that the appliance responds
correctly to the commands sent.
If there is no response or the appliance
only responds partially or incorrectly,
it is probable that you have used
the wrong code. In this case, try the
procedure again from point 3.
This time, however, use the
NEXT CODE in the list (e.g. 099).
Note down the TV code used to program
the remote control on the adhesive label
inside the battery cover for rapid
consultation.
NOTE: THE LIGHT INDICATOR
STOPS FLASHING
The remote control leaves the
programming mode and the light indicator
stops flashing:
•if no keys are pressed for 15 seconds
•if an invalid brand code is entered.
8
0
7
5
DIRECT CODE ENTRY
FOR REMOTE CONTROLS VERSIONS
V5 - V6
B
DIRECT CODE ENTRY
FOR REMOTE CONTROLS VERSIONS FROM
V1 TO V4
B
PAY ATTENTION TO THE REMOTE CONTROL VERSION
1.Make sure that the TV is ON.
2.In the code book enclosed,
look for the brand of your TV
and make a note of the first
code indicated BENEATH
the brand previously identified
(e.g. Philips 103).
3.Hold down the SHIFT
and ON/OFF keys together
until the light indicator at the top
starts to flash indicating that the
remote control is in programming
mode.
4.Release the keys.
Within 15 seconds, enter the
code previously identified
(e.g. 103). Three flashes indicate
that the code has been saved
correctly. If not, try the code entry
procedure again from point 3.
Additional check
Point the remote control at the TV.
Check that the appliance responds
correctly to the commands sent.
If there is no response or the appliance
only responds partially or incorrectly,
it is probable that you have used
the wrong code. In this case, try the
procedure again from point 3.
This time, however, use the
NEXT CODE in the list (e.g. 111).
Note down the TV code used to program
the remote control on the adhesive label
inside the battery cover for rapid
consultation.
NOTE: THE LIGHT INDICATOR
STOPS FLASHING
The remote control leaves the
programming mode and the light indicator
stops flashing:
•if no keys are pressed for 15 seconds
•if an invalid brand code is entered.
1
0
3


Product specificaties

Merk: Meliconi
Categorie: Afstandsbediening
Model: Control TV

Heb je hulp nodig?

Als je hulp nodig hebt met Meliconi Control TV stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Meliconi

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening