MB Quart NA3-560.4 Handleiding

MB Quart Receiver NA3-560.4

Lees hieronder de đź“– handleiding in het Nederlandse voor MB Quart NA3-560.4 (16 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
It is critical to use the proper power
and ground cable. Select the size
listed here for your ampliî‚żer model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the ampliî‚żer to
a secure surface. Do not mount
the ampliî‚żer upside down.
Attach the chassis ground, +12V and amp turn on
wire. It is important to make sure these connections
are very secure.
REM TURN ON / DC SENSE ON SWITCH
There are two methods of switching the ampliî‚żer on and off. Select the appropriate
position suited for your application.
REM TURN ON This will turn on the ampliî‚żer when a +12v switched power typically
from a source unit, is connected to the Amp Turn On - BLUE wire on the main power
connection harness.
DC SENSE The DC SENSE is for use with source units that do not offer RCA
outputs.
PLEASE NOTE: If switch is set to DC sense on, the ampliî‚żer will not turn
on via the ampliî‚żers remote turn on wire. So if ampliî‚żer will not turn on
please view this switch on the top control panel and adjust accordingly.
For more information on DC Sense and wiring visit MBQUART.com
Bare metal
Connect the RCA cables to the
INPUT connectors.
Connect the power cable to
positive battery terminal. Th
power cable must be fused
within 18 inches of the batte
terminal.
Re-connect the negative
battery terminal making sure
is securely tightened.
The chassis ground connection
is critical to the performance
of the ampliî‚żer. Choose a
location that is close to the
ampliî‚żer. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
Negative Battery
Terminal
Run Cables
Mount Ampliî‚żer
Power
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Batter
Terminal
Speaker
Connections
Chassis Ground
Be prepared t
to enter y
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
6
9
10
84
Turn the GAIN control completely
counter-clockwise to minimum.
Gain Control
7
10ga
Model Cable Size
NA3-560.4
NA3-1000.5
NA3-600.6
CH1 Negative - White / Black
CH2 Positive - Gray
Ground - Black
Amp Turn On- Blue
+12V - Red
GAIN
MIN MAX
Congratulations on your choice of a MBQuart amplier. This “Quick Start
Installation” guide is meant to help you “hook up” and play music. For more
detailed information, on system setting, speaker and subwoofer conî‚żguration
and full speciî‚żcations by model please visit our website at www.MBQuart.com


Product specificaties

Merk: MB Quart
Categorie: Receiver
Model: NA3-560.4

Heb je hulp nodig?

Als je hulp nodig hebt met MB Quart NA3-560.4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver MB Quart

Handleiding Receiver

Nieuwste handleidingen voor Receiver