Maytag W10655450 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Maytag W10655450 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
W10758628A
BACKSPLASH
Use & Care / Installation Instructions
PANNEAU ANTI-ÉCLABOUSSURE
Utilisation et entretien / Instructions d’installation
Table of Contents/Table des matieres
INSTALLATION REQUIREMENTS………………………….1 EXIGENCES D’INSTALLATION....………………....……....……............................3
INSTALLATION INSTRUCTIONS……………………………2 INSTRUCTIONS D’INSTALLATION…………………...………...............................4
BACKSPLASH USE & CARE………………………………..2 UTILISATION ET ENTRETIEN DU PANNEAU ANTI-ÉCLABOUSSURE.............4
INSTALLATION REQUIREMENTS
• Level
• Stud Finder
• Phillips Head Screwdriver
Parts Supplied
• Backsplash
• Wall brackets
• Screws, 8-18 x ½”
• Screws, 10-2 x 2”
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided
with any tools listed here.
Tools Required
• Drill
• 1/8” Drill Bit
• Tape Measure
Location Requirements
The backsplash can be installed on the backwall behind a slide-in, commercial style range or cooktop.
Appliance must be level side to side and front to back.
Backsplash Dimensions
B
A
A. Backsplash width, 30
B. Backsplash height, 7 3/8”
INSTALLATION INSTRUCTIONS
Mark Guide Lines
1. Mark a small line on the backwall at the height of the range
or cooktop.
2. Measure 1 3/8” down from this line and draw a level line the
full length of the installation space. This line represents the
bottom edge of backsplash line.
3. Position the bottom edge of the ange along the bottom
edge of backsplash line. Align the center of the backsplash
with the center of the appliance. Mark each mounting hole
(2 locations) with a pencil. Set panel aside.
4. Measure up 6 3/8” from the bottom edge of backsplash
line and draw a level line the full length of the installation
space. This mounting bracket guide line represents where
the mounting brackets will attach to the wall.
2
Align this surface
with the mounting
bracket guide line
Install Mounting Brackets
1. Usingastudnder,locatetheedgesofthewallstudswithin
the installation space.
2. Mark the center of each stud and draw a line down the center
of the stud.
3. Line up the top of the wall mounting bracket with the mounting
bracket guide line from “Mark Guide Lines” section.
4. Center a bracket along the centerline of each wall stud.
5. Mount each bracket to wall using two 10-12 x 2” screws
per bracket (included with kit). A minimum of two mounting
brackets should be installed for the 30” models.
Install Backsplash
1. HooktheangeonthebackoftheBacksplashoverthemountingbracketsattachedtothewall.
2. Center the Backsplash and align the two holes at the bottom of the Backsplash with the marks on the wall made in
the “Mark Guide Lines” section.
3. Attachbrackettowallusingthetwo10-12x2”screwsthroughtheholesatthebottomoftheange.
BACKSPLASH USE & CARE
General Cleaning
Donotusesoap-lledscouringpads,abrasivecleaners,CooktopPolishingCreme,steel-woolpads,grittywashcloths
or abrasive paper towels. Damage may occur, even with one-time or limited use. Rub in direction of grain to avoid
damaging.
Cleaning Method:
• Affresh® Stainless Steel Cleaner and Polish: Follow the instructions found on the label of the cleaner.
• Liquid detergent or all-purpose cleaner: Rinse with clean water and dry with soft, lint-free cloth.
Center
Line
Mounting Bracket
Guide Line
Bottom Edge of Backsplash
Range/Cooktop
Height
6 3/8”
1 3/8”
W10758628A
W10758628A
PANNEAU ANTI-ÉCLABOUSSURE
Utilisation et entretien / Instructions d’installation
Table des matieres
EXIGENCES D’INSTALLATION....………………....……....……............................3
INSTRUCTIONS D’INSTALLATION…………………...………...............................4
UTILISATION ET ENTRETIEN DU PANNEAU ANTI-ÉCLABOUSSURE.............4
EXIGENCES D’INSTALLATION
• Niveau
• Détecteur de poteaux structuraux
• Tournevis cruciforme Phillips
Pièces fournies
• Panneau anti-éclaboussure
• Supports muraux
• Vis 8-18 x ½”
• Vis 10-2 x 2”
Outils et pièces
Rassembler les outils et composants nécessaires avant d’entreprendre l’installation. Lire et observer les
instructions fournies avec chacun des outils de la liste ci-dessous.
Outillage nécessaire
• Perceuse
• Foret de 1/8”
• Ruban à mesurer
Exigences d’emplacement
Le panneau anti-éclaboussure peut être installé sur le mur du fond, derrière une cuisinière ou une table de
cuisson encastrée de style commercial. L’appareil doit être horizontal dans le sens latéral et en profondeur.
Dimensions du panneau anti-éclaboussure
B
A
A. Largeur du panneau, 30”
B. Hauteur du panneau, 7 3/8”
3


Product specificaties

Merk: Maytag
Categorie: Niet gecategoriseerd
Model: W10655450

Heb je hulp nodig?

Als je hulp nodig hebt met Maytag W10655450 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Maytag

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd