Maytag MIM1555ZRS Handleiding

Maytag Ijsmachine MIM1555ZRS

Lees hieronder de 📖 handleiding in het Nederlandse voor Maytag MIM1555ZRS (24 pagina's) in de categorie Ijsmachine. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/24

ICE MAKER INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION DE

LA MACHINE À GLAÇONS

ICE MAKER SAFETY

Table of Contents/Table des matières

ICE MAKER SAFETY......................................................................1

INSTALLATION INSTRUCTIONS..................................................2

Unpack the Ice Maker..................................................................2

Location Requirements................................................................2

Electrical Requirements ...............................................................3

Water Supply Requirements........................................................3

Vacation or Extended Time Without Use.....................................3

Connect Water Supply.................................................................3

Ice Maker Drain Pump Installation...............................................4

Drain Connection .........................................................................7

Ice Maker Door Reversal—Side Swing Only ...............................8

Leveling ......................................................................................10

Cleaning......................................................................................10

SÉCURITÉ DE LA MACHINE À GLAÇONS ................................12

INSTRUCTIONS D’INSTALLATION.............................................13

Déballage de la machine à glaçons ...........................................13

Exigences d’emplacement.........................................................13

Spécifications électriques ..........................................................13

Spécifications de l’alimentation en eau .....................................14

Vacances ou longue période d’inutilisation ...............................14

Raccordement à la canalisation d’eau.......................................14

Installation de la pompe de vidange de

la machine à glaçons..................................................................15

Raccordement au drain de vidange...........................................18

Inversion du sens d’installation de la machine à glaçons—

Porte à ouverture latérale uniquement.......................................19

Nivellement.................................................................................21

Nettoyage ...................................................................................22

W10541636B

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING

: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic

precautions:

SAVE THESE INSTRUCTIONS

■

Plug into a grounded 3 prong outlet.

■

Do not remove ground prong.

■

Do not use an adapter.

■

Do not use an extension cord.

■

Disconnect power before manually cleaning the inside components.

■

Disconnect power before servicing.

■

Replace all parts and panels before operating.

■

Use two or more people to move and install ice maker.

INSTALLATION INSTRUCTIONS

Unpack the Ice Maker

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

■To remove any remaining tape or glue from the exterior of the

ice maker, rub the area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with your

fingers. Wipe with warm water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless steel surfaces of the ice

maker. These products can damage the surface of your

ice maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside

of your ice maker before using it. See the cleaning instructions in

the “Ice Maker Care” section.

Location Requirements

■To ensure proper ventilation for your ice maker, the front side

must be completely unobstructed. The ice maker may be

closed-in on the top and three sides, but the installation

should allow the ice maker to be pulled forward for servicing

if necessary.

■Installation of the ice maker requires a cold water supply inlet

of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve or

a Whirlpool supply line Part Number 8212547RB, and a

Whirlpool approved drain pump, Part Number 1901A, only to

carry the water to an existing drain.

■Choose a well ventilated area with temperatures above 55°F

(13°C) and below 110°F (43°C). Best results are obtained

between 70°F and 90°F (21ºC and 32°C).

■The ice maker must be installed in an area sheltered from the

elements, such as wind, rain, water spray, or drip.

■When installing the ice maker under a counter, follow the

recommended opening dimensions shown. Place electrical

and plumbing fixtures in the recommended location as

shown.

NOTES:

■Check that the power supply cord is not damaged, or

pinched or kinked between the ice maker and the

cabinet.

■Check that the water supply line is not damaged, or

pinched or kinked between the ice maker and the

cabinet.

■Check that the drain line (on some models) is not

damaged, or pinched or kinked between the ice maker

and the cabinet.

■Check that the ice maker door is not flush with the front of

standard cabinets to avoid problems with opening the ice

maker door.

■Choose a location where the floor is even. It is important for

the ice maker to be level in order to work properly. If needed,

you can adjust the height of the ice maker by changing the

height of the leveling legs. See “Leveling.”

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

WARNING

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

A. Recommended location for electrical

and plumbing fixtures

B. Floor level

C. 15" or 18" (38.1 cm or

45.7 cm) depending on

model

3¹⁄₂"

(8.9 cm)

(22.9 cm)

11 "¹⁄₂

(29.2 cm)

24"

(60.1 cm)

34"

(86.4 cm)

Min.

34 "¹⁄₂

(87.6 cm)

Max.

28 "¹⁄₂

(72.4 cm)

Electrical Requirements

Before you move your ice maker into its final location, it is

important to make sure you have the proper electrical

connection:

A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical supply,

properly grounded in accordance with the National Electrical

Code and local codes and ordinances, is required.

It is recommended that a separate circuit, serving only your ice

maker, be provided. Use a receptacle which cannot be turned off

by a switch or pull chain.

IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) equipped outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Ice quality

may be affected. If nuisance tripping has occurred, and if the

condition of the ice appears poor, dispose of it.

Recommended Grounding Method

The ice maker must be grounded. The ice maker is equipped with

a power supply cord having a 3 prong grounding plug. The cord

must be plugged into a mating, 3 prong, grounding-type wall

receptacle, grounded in accordance with the National Electrical

Code and local codes and ordinances. If a mating wall receptacle

is not available, it is the personal responsibility of the customer to

have a properly grounded, 3 prong wall receptacle installed by a

qualified electrician.

Water Supply Requirements

Check that the water supply lines are insulated against freezing

conditions. Ice formations in the supply lines can increase water

pressure and damage your ice maker or home. Damage from

frozen supply lines is not covered by the warranty.

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker. If

you have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT:

■A reverse osmosis system is not recommended for ice

makers that have a drain pump installed.

■For gravity drain systems only.

■The pressure of the water supply coming out of a reverse

osmosis system going to the water inlet valve of the ice

maker needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of

water per hour to the ice maker for proper ice maker operation. If

a reverse osmosis system is desired, only a whole-house

capacity reverse osmosis system, capable of maintaining the

steady water supply required by the ice maker, is recommended.

Faucet capacity reverse osmosis systems are not able to

maintain the steady water supply required by the ice maker.

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Vacation or Extended Time Without Use

■When you will not be using the ice maker during the summer

months, turn off the water and power supply to the ice maker.

■Make sure the water supply lines are protected against

freezing conditions. Ice formations in the supply lines can

increase water pressure and cause damage to your ice maker

or home. Damage from freezing is not covered by the warranty.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■Use copper tubing or Whirlpool supply line, Part Number

8212547RP, and check for leaks.

■Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed

Gather the required tools and parts before starting installation:

■Flat-blade screwdriver

■⁷⁄₁₆ ¹⁄₂" and " open-end wrenches or two adjustable wrenches

■¹⁄₄" nut driver

NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily.

Connecting the Water Line

1. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

2. Using a ¹⁄₂" copper supply line with a quarter-turn shutoff

valve or the equivalent, connect the ice maker as shown.

NOTE: To allow sufficient water flow to the ice maker a

minimum ¹⁄₂" diameter home supply line is recommended.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Product specificaties

Merk:	Maytag
Categorie:	Ijsmachine
Model:	MIM1555ZRS

Heb je hulp nodig?

Als je hulp nodig hebt met Maytag MIM1555ZRS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ijsmachine Maytag

Maytag MIM1554ZRS Handleiding

17 Augustus 2023

Maytag MIM1555ZRS Handleiding

17 Augustus 2023

Handleiding Ijsmachine

Nieuwste handleidingen voor Ijsmachine

Ninja Creami Deluxe NC501 Handleiding

20 November 2024

Scotsman B330P Handleiding

19 November 2024

Waring Commercial WCIC25 Handleiding

16 November 2024

Jocel JMFG001764 Handleiding

15 November 2024

Royal Catering RCHI-01 Handleiding

14 November 2024

Cuisinart ICE31U Handleiding

23 Oktober 2024

Yamazen YSIA-F25 Handleiding

23 Oktober 2024

Summit BIM182 Handleiding

20 Oktober 2024

Edgestar IB250BL Handleiding

20 Oktober 2024

Edgestar IB121SS Handleiding

20 Oktober 2024