Maxicool LMD-12HDI Handleiding

Maxicool Airconditioners LMD-12HDI

Lees hieronder de 📖 handleiding in het Nederlandse voor Maxicool LMD-12HDI (2 pagina's) in de categorie Airconditioners. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Fit the Installation Plate and drill

holes in the wall according to the

wall structure and corresponding

mounting points on the installation

plate. The installation plate provided

with the machine differ from appliance

to appliance.

(Dimensions are in mm unless

otherwise stated)

1. Determine hole positions according to left and right

side of the installation plate. The hole center is obtained

by measuring the distance as shown in the diagram above.

2. Dirll the piping plate hole with 65mm hole-core drill.φ

3. Drill the piping hole at either the right or the left and the

hole should be slightly slanted to the outdoor side.

4. Always use wall hole conduit when drilling metal grid,

metal plate or the like.

1. For the left-hand and right-hand piping,

remove the pipe cover from the side panel.

2. For the rear-right-hand and rear-left-hand

piping, install the piping as shown.

3. Bundle the tubing, connecting cable, and

drain hose with tape securely, evenly as

shown in Figure on the right.

Because the condensed water from rear

of the indoor unit is gathered in ponding

box and is piped out of room. Do not put

anything else in the box.

1. Run the drain hose sloping downward.

Do not install the drain hose as illustrated

in Figures.

2. When connecting extension drain hose,

insulate the connecting part of extension

drain hose with a shield pipe, do not let

the drain hose slack.

Connect the indoor unit first, then the

outdoor unit.

Do not allow the piping to let out from the

back of the indoor unit.

Be careful not to let the drain hose slack.

Heat insulated both of the auxiliary piping.

Be sure that the drain hose is located at

the lowest side of the bundle. Locating at

the upper side can cause drain pan to

overflow inside the unit.

Never intercross nor intertwist the power

wire with any other wiring.

Run the drain hose slopped downward to

drain out the condensed water smoothly.

1. Pass the piping through the hole in the wall.

2. Hook the indoor unit onto the upper portion

of installation plate(Engage the indoor unit with

the upper edge of the installation plate). Ensure

the hooks are properly seated on the installation

plate by moving it in left and right.

3. Piping can easily be made by lifting the indoor

unit with a cushioning material between the

indoor unit and the wall. Get it out after finish

piping.

4. Press the lower left and right side of the unit

against the installation plate until hooks

engages with the their slots.

INSTALLATION MANUAL FOR ROOM

AIR CONDITIONER

(Split Wall-Mounted Type)

DRILL A HOLE IN THE WALL

FIT THE INSTALLATION PLATE

CONNECTIVE PIPE AND DRAINAGE INSTALLATION

Connective pipe installation

Drainage

CAUTION

Indoor unit installation

" "

Cor rect orientation

of Installation Plate

Installation Plate

Clip Anchor

Self-tapping Screw A ST3.9x25

Seal(For cooling & heating models only)

Drain Joint(For cooling & heating models only ）

Connecti ng

pipe

Assembly

Liquid side

Gas side

Remote controller

Self-tapping Screw B ST2.9x10

Φ6.35

Φ9.52

Φ12.7

Φ 16

Parts you must purchase. The pipe

size differ from appliance to appliance.

Consult the technician for the proper

size.

5-8(depending on models)

Except the above parts provided,the other parts needed during installation you must

purchase.

Remote controller holder

ACCESSORIES

Number

Name of Accessories Qty

NOTE:

optional

parts

Outdoor unit dimension

mm(WxHxD)

A(mm)

458

B(mm)

250

530

600

290

320

560

549

460

481

335

276

Mount ing d imensi ons

700x540 x240

760x590 x285

775x545 x310

845x700 x320

780x540 x250

685x430 x260

670x540 x265

SELECT THE BEST LOCATION

The seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to property.

1) This equipment must be earthed and installed with earth leakage current breaker. It may cause

electrical shock if grounding is not perfect.

2) Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and

accumulates at surrounding of the unit, it may cause fire.

3) Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water

may enter the room and damage the furniture.

1) Install according to this installation instructions strictly. If installation is defective, it will cause water

leakage, electrical shock fire.

2) Use the attached accessories parts and specified parts for installation, otherwise, it will cause the se t

to fall, water leakage, electrical shock fire.

3) Install at a strong and firm location which is able to withstand the set s weight. If the strength is not

enough or installation is not properly done, the set will drop and cause injury.

4) For electrical work, follow the local national wiring standard, regulation and this installation instructions.

An independent circuit and single outlet must be used. If electrical circuit capacity is not enough or

defect found in electrical work, it will cause electrical shock fire.

5) Use the specified cable and connect tightly and clamp the cable so that no external force will be acted

on the terminal. If connection or fixing is not perfect, it will cause heat-up or fire at the connection.

6) Wiring routing must be properly arranged so that control board cover is fixed properly. If control board

cover is not fixed perfectly, it will cause heat-up at connection point of terminal, fire or electrical shock.

7) When carrying out piping connection, take care not to let air substances other than the specified

refrigerant go into refrigeration cycle. Otherwise, it will cause lower capacity, abnormal high pressure

in the refrigeration cycle, explosion and injury.

8) Do not modify the length of the power supply cord or use of extension cord, and do not share the

single outlet with other electrical appliances. Otherwise, it will cause fire or electrical shock.

SAFETY PRECAUTIONS

CAUTION

WARNING

CAUTION

WARNING

Please read this installation manual completely before installing the product.

If the power cord is damaged, replacement work shall be performed by authorised personnel only.

Installation work must be performed in accordance with the national wiring Standards by authorised

personnel only.

Contact an authorised service technician for repair, maintenance or installation of this unit.

This appliance is not intended for use by persons(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The design and specifications are subject to change without prior notice for product improvement.

Consult with the sales agency or manufacturer for details.

All the pictures in the instructions are for explanation purposes only. The actual shape should prevail.

There should not be any heat source or stream

near the unit.

There should not be any obstacles blocking the

air circulation.

A place where air circulation in the room is good.

A palce where drainage can be easily done.

A palce where noise prevention is taken into

consideration.

Do not install the unit near the door way.

Ensure the spaces indicated by arrows from the

wall,ceiling,fence or other obstacles.

There should not be any direct sunlight. If unavoidable,

sunlight prevention should be taken into consideration.

Indoor unit

Outdoor unit

If an awning is built over the unit to prevent

direct sunsight or rain,be careful that heat

radiation from the condenser is not obstructed.

There should not be any animal or plant which

could be affected by hot air discharged.

Keep the spaces indicated by arrow from wall

ceiling, fence or other obstacles.

Do not place any obstacles which may cause

a short circuit of the discharged air.

Anchor the outdoor unit with a bolt and nut 10 or φ

φ8 tightly and horizontally on a concrete or rigid mount.

Settlement of outdoor unit

NOTE: The outdoor unit you purchase may be like one

of the following. Install the outdoor unit according to the

dimension as indicated in the table below:

Air outlet

Air inlet

1. Fit the installation plate horizontally

on structural parts of the wall with

spaces around the installation plate.

2. If the wall is made of brick, concrete

or the like, drill five or eight 5mm diameter

holes in the wall.Insert Clip anchor for

appropriate mounting screws.

3. Fit the installation plate on the wall

with five or eight type A screws.

NOTE:

Fit the Installation Plate

The mounting wall is strong and solid

enough to prevent it from the vibration.

" "

150 or more to ceiling

Indoor unit outline Installation plate

292

Right rear side

refrigerant

pipe hole 65φ

Left rear side

refrigerant

pipe hole 65φ

120 or more

to wall

120 or more

to wall

920

185

150

Right rear side

refrigerant

pipe hole 65φ

Installation plate

Indoor unit outline

Left rear side

refrigerant

pipe hole 65φ

150 or more to ceiling

120 or more

to wall

120 or more

to wall

Model A (A: 710, B: 250, C:100, D: 110)

Model B( )A: 790, B:265, C:100, D: 150

Model C

Model D

120mm or more

from the wall

120mm or more

from the wall

150mm or more from the ceiling

Indoor Unit Outline

Hooked Part

998

100 120

322

202000192534 CS211I-BP9A1U(HL) 20130622

AIR PURGING AND TEST OPERATION

Liquid side: 6.35mmφ

R22: (Pipe length-5)x30g/m

R410A: (Pipe length-5)x20g/m

Liquid side: 9.52mm:φ

R22: (Pipe length-5)x60g/m

R410A: (Pipe length-5)x40g/m

Connective pipe length

Less than 5m

More than 5m

Air purging method

Use vacuum pump

Additional amount of refrigerant to be charged

Open the valve stem until it hits against

the stopper. Do not try to open it further.

Securely tighten the valve stem cap with

a spanner or the like.

Valve stem cap tightening torque. See

Tightening torque table.

Flare nut

Stopper

Cap

Valve body

Valve stem

Use vacuum pump

For the R407C refrigerant model, make sure the refrigerant added into air conditioner is liquid

form in any cases.

When relocate the unit to another place, using vacuum pump to perform evacuation.

Air and moisture in the refrigerant system have undesirable effects. Therefore, the indoor unit

and tubing between the indoor and outdoor unit must be leak tested and evacuated to remove

any noncondensables and moisture from the system.

Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have

been properly connected and all wiring for the test run has been completed.

Pipe length and refrigerant amount:

Outdoor

unit

Indoor

unit

Refrigerant

Packed valve

Half union

Gas side

Liquid side

1. Completely tighten the flare nuts, A, B, C, D, connect

the manifold valve charge hose to a charge port of the

packed valve on the gas pipe side.

2. Connect the charge hose connection to the vacuum

pump.

3. Fully open the handle Lo of the manifold valve.

4. Operate the vacuum pump to evacuate. After starting

evacuation, slightly loose the flare nut of the packed

valve on the gas pipe side and check that the air is

entering. (Operation noise of the vacuum pump changes

and a compound meter indicates 0 instead of minus)

5. After the evacuation is complete, fully close the handl e

Lo of the manifold valve and stop the operation of the

vacuum pump.

Make evacuation for 15 minutes and more and check

that the compound meter indicates -76cmHg(-1.0x10 Pa).

6. Turn the stem of the packed valve B about 45 counter-

clockwise for 6~7 seconds after the gas coming out, then

tighten the flare nut again. Make sure the pressure display

in the pressure indicator is a little higher than the atmosphere

pressure.

7. Remove the charge hose from the Low pressure charge hose.

8. Fully open the packed valve stems B and A.

9. Securely tighten the cap of the packed valve.

Manifold valve

Compound meter

-76cmHg

Handle Lo Handle Hi

Charge hose Charge hose

Vacuum pump

Pressure gauge

Packed valve

Perform test operation after completing gas leak check at the flare nut connections and electrical

safety check.

Check that all tubing and wiring have been properly connected.

Check that the gas and liquid side service valves are fully open.

1. Connect the power, press the ON/OFF button on the remote controller to turn the unit on.

2. Use the MODE button to select COOL, HEAT, AUTO and FAN to check if all the functions works

well.

3. When the ambient temperature is too low(lower than 17 C), the unit cannot be controlled by the

remote controller to run at cooling mode, manual operation can be taken. Manual operation is

used only when the remote controller is disable or maintenance necessary.

Hold the panel sides and lift the panel up to an angle until it remains fixed with a clicking sound.

Press the Manual control button to select the AUTO or COOL, the unit will operate under Forced

AUTO or COOL mode(see User Manual for details).

4. The test operation should last about 30 minutes.

1. Air purging

2. When using the Vacuum Pump

4. Test running

3. Safety and leakage check

A: Lo packed valve B: Hi packed valve

C and D are ends of indoor unit connection.

CAUTION

1. Soap water method:

Apply a soap water or a liquid neutral detergent on the indoor

unit connections and outdoor unit connections by a soft brush

to check for leakage of the connecting points of the piping. If

bubbles come out, it indicates that the pipes have leakage.

2. Leak detector

Use the leak detector to check for leakage.

CONNECT THE CABLE TO THE OUTDOOR UNIT

CAUTION

Indoor unit

check point D

Outdoor unit

check point

Cover

Electrical box

cover

Front Panel

Manual control

button

AUTO/COOL

Connect the cable to the indoor unit

Before performing any electrical work, turn off the main power to the system.

1. The inside and outside connecting cable can be connected without removing the front grille.

2. The indoor power cord type is H05VV-F or H05V2V2-F, the outdoor power cord and

interconnected cord type is H07RN-F.

3. Lift the indoor unit panel up, remove the electrical box cover by loosening the screw.

4. Ensure the colour of wires of outdoor unit and the terminal Nos. are the same to the indoor s

respectively.

5. Wrap those cables not connected with terminals with insulation tapes, so that they will not touch

any electrical components. Secure the cable onto the control board with the cord clamp.

NOTE:

NOTE: If used as MONO unit, for the standby control needs, the cross section area of cable connected

to L(1), 1, 2(N) must be sufficient for the maximum system current. The maximum system current is

equal to the sum of indoor unit and outdoor unit rated current.

Terminal block of indoor unit

To outdoor unit

L(1)

2(N)

1. Remove the electrical control board cover from the outdoor unit by loosening the screw.

2. Connect the connective cables to the terminals as identified with their respective matched number s

on the terminal block of indoor and outdoor units.

3. Secure the cable onto the control board with the cord clamp.

4. To prevent the ingress of water, form a loop of the connective cable as illustrated in the installation

diagram of indoor and outdoor units.

5. Insulate unused cords (conductors) with PVC-tape. Process them so they do not touch any electrica l

or metal parts.

Cover

Screw

Terminal block of outdoor unit

To indoor unit Power supply

2(N)

L N

L(1)

CONNECT THE CABLE TO THE INDOOR UNIT

Install the outdoor unit on a rigid base to prevent increasing noise level and vibration.

Determine the air outlet direction where the discharged air is not blocked.

In the case that the installation place is exposed to strong wind such as a seaside, make

sure the fan operating properly by putting the unit lengthwise along the wall or using a dust

or shield plates.

Specially in windy area, install the unit to prevent the admission of wind. If need suspending

installation, the installation bracket should accord with technique requirement in the

installation bracket diagram. The installation wall should be solid brick, concrete or the same

intensity construction, or actions to reinforce, damping supporting should be taken.

The connection between bracket and wall, bracket and the air conditioner should be firm,

stable and reliable.

Be sure there is no obstacle which block radiating air.

Strong

wind

Strong

wind

Barrier

Incorrect Correct

Seal

Drain joint

Base pan hole

of outdoor unit

(A) (B)

The drain joint is slightly different according to the

different outdoor unit.

For the drain joint with the seal(Fig.A), first fit the seal onto

the drain joint, then insert the drain joint into the base pan

。

hole of outdoor unit, rotate 90 to securely assemble them.

To install drain joint as shown in Fig.B, insert the drain

joint into the base pan hole of outdoor unit until it remains

fixed with a clicking sound. Connecting the drain joint with

an extension drain hose (Locally purchased), in case of the

water draining off the outdoor unit during the heating mode.

DRAIN JOINT INSTALLATION

OUTDOOR INSALLATION PRECAUTION

Oblique

90 Roughness

Burr

REFRIGERANT PIPE CONNECTION

1. Cut a pipe with a pipe cutter.

2. Remove flare nuts attached to indoor and

outdoor unit, then put them on pipe/tube

having completed burr removal and flare

the pipe.

3. Firmly hold copper pipe in a die in the

dimension shown in the table below.

Align pipes to be connected.

Sufficiently tighten the flare nut with fingers,

and then tighten it with a spanner and torque

wrench as shown.

Excessive torque can break nut depending

on installation conditions.

Outer diam.

(mm)

A(mm)

Max. Min.

6.35 1.3 0.7

9.52

1.6 1.0

12.7

1.8 1.0

12.7

1.8

2.2

1.0

2.0

Bar

Copper pipe Clamp handle

Handle

Bar

"A"

Indoor unit tubing Flare nut Pipings

Outer

diam. Tightening

torque(N.cm) Additional tightening

torque(N.cm)

φ6.35mm

φ12.7mm

φ16mm

φ9.52mm

1500

(153kgf.cm) 1600

(163kgf.cm)

3500

(357kgf.cm)

4500

(459kgf.cm)

3600

(367kgf.cm)

4700

(479kgf.cm)

2500

(255kgf.cm)

2600

(265kgf.cm)

Flaring

Tightening connection

NOTE:

Electric safety regulations for the initial Installation

1. If there is serious safety problem about the power supply, the technicians should refuse to install

the air conditioner and explain to the client until the problem is solved.

2. Power voltage should be in the range of 90%~110%of rated voltage.

3. The surge protector and main power switch with a 1.5 times capacity of Max. Current of the unit should

be installed in power circuit. Ensure the air conditioner is grounded well.

4. The appliance shall be installed in accordance with national wiring regulations. Do not operate your air

conditioner in a wet room such as a bathroom or laundry room.

5. An all-pole disconnection device which has at least 3mm clearances in all poles, and have a leakage

current that may exceed 10mA, the residual current device(RCD) having a rated residual operating

current not exceeding 30mA, and disconnection must be incorporated in the fixed wiring in accordance

with the wiring rules.

6. For the unit adopts auxiliary electric heater, keep at least 1 meter away from the nearest combustible

materials.

7. According to the attached Electrical Connection Diagram located on the panel of the indoor & outdoor

unit to connect the wire. All wiring must comply with local and national electrical codes and be installed

by qualified and skilled electricians.

8. An individual branch circuit and single receptacle used only for this air conditioner must be available.

See the following table for suggested wire sizes and fuse specifications:

Minimum cross-sectional area of conductors:

Rated current

of appliance

(A)

>3 and ≤6

>6 and ≤10

>10 and ≤16

>16 and ≤25

>25 and ≤32

>32 and ≤40

Nominal cross-sectional

area

(mm2)

0.75

1.5

2.5

Electrical work

The wire size of power supply cord and

interconnected wire and the current of

the fuse or switch are determined by the

maximum current indicated on the

nameplate which located on the side panel

of the unit. Please refer to the nameplate

before selecting the wire size, fuse or switch.

The controller of the air conditioner designed

with a fuse protection function under

abnormal conditions, the specifications of

the fuse have printed on the circuit board,

such as: 3.15A/250VAC, T5A/250VAC, etc.

NOTE:

NOTE: Connective pipe length will affect the capacity and energy efficiency of the unit. The

nominal efficiency is tested basing on the pipe length of 5 meters.

Product specificaties

Merk:	Maxicool
Categorie:	Airconditioners
Model:	LMD-12HDI

Heb je hulp nodig?

Als je hulp nodig hebt met Maxicool LMD-12HDI stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Airconditioners Maxicool

Maxicool SGL-1AHDC Handleiding

4 Oktober 2022

Maxicool KGL18HDA Handleiding

4 Oktober 2022

Maxicool LMD-M09 Handleiding

4 Oktober 2022

Maxicool LMD-12HDI Handleiding

4 Oktober 2022

Maxicool SGL-09HOC Handleiding

4 Oktober 2022

Maxicool LMD-09HDI Handleiding

4 Oktober 2022

Maxicool DMD-M09 Handleiding

4 Oktober 2022

Handleiding Airconditioners

Nieuwste handleidingen voor Airconditioners

Haier AC12CS1ERA Handleiding

4 Oktober 2022

Tarrington House MAC2510C Handleiding

4 Oktober 2022

Camry CR 7910 Handleiding

4 Oktober 2022

BEKO BEHPH 241 Handleiding

4 Oktober 2022

Frigidaire FFRP092LT3 Handleiding

4 Oktober 2022

Danby DAC050MB1WDB Handleiding

4 Oktober 2022

Toshiba RAS-4M23SAV-E Handleiding

4 Oktober 2022

Daitsu ADP 12A Handleiding

4 Oktober 2022

Frigidaire FFRE0533S1 Handleiding

4 Oktober 2022

Infiniton PAC-S10 Handleiding

4 Oktober 2022