Masport Westcott 2000 Handleiding

Masport Heater Westcott 2000

Lees hieronder de 📖 handleiding in het Nederlandse voor Masport Westcott 2000 (8 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
Installation Instructions
Westcott 1000
Westcott 2000
Keep instructions for future reference
Glen Dimplex Australia proudly supports the activities of Landcare Australia through its membership of the AHHA
Version 1.2 2
1.0
IMPORTANT INFORMATION …………………….....
2
2.0
ASSEMBLY OF THE HEATER …………………………..
3
3.0
INSTALLING THE HEATER ………………………………
4
4.0
REDUCING CLEARANCES TO COMBUSTIBLES. ..
5
5.0
INSTALLING THE FLUE …………………………….…….
6
6.0
TECHNICAL DRAWINGS …………… …………..………
7
Most building regulatory Authorities in Australia require any
wood heater installation to comply with Installation Standard
AS/NZS 2918:20 . Different states and councils may have 18
varying regulations. Check local building regulations before
installing the appliance.
The Masport Westcott 1000 and 2000 wood heaters have
been tested to ensure that they will meet the appropriate
safety Standard requirements if the instructions in this manual
are followed. As the safety and emissions performance can be
affected by altering the appliance, no modifications are
allowed without written permission from the manufacturer.
WE RECOMMEND THAT THE INSTALLATION OF YOUR
MASPORT WOOD HEATER BE CARRIED OUT BY A QUALIFIED
INSTALLER.
WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE
INSTALLED IN ACCORDANCE WITH AS/NZS 2918:20 AND 18
THE APPROPRIATE REQUIREMENTS OF THE RELEVANT
BUILDING CODE OR CODES.
WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH
THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS
OF AS/NZS 4012 & AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY, I.E. THE APPLIANCE SHALL BE
IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING
‘TESTED TO AS/NZS 4012 & AS/NZS 4013’.
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN
APPROVED IN WRITING BY THE TESTING AUTHORITY IS
CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED
FOR COMPLIANCE WITH AS/NZS 4012 & AS/NZS 4013.
CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM
COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY
RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS
CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
CAUTION: CRACKED AND BROKEN COMPONENTS, EG. GLASS
PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION
UNSAFE.
1. IMPORTANT INFORMATION
TABLE OF CONTENTS
Version 1.2 3
To make the heater easier for handling on installation, remove
the baffle plate, side and back bricks and door. Please these in
a secure plate to avoid damage. These must be refitted after
installation.
The legs and other fixings are packed in the ashpan for safe
keeping in transport. Fix the legs to the underside of the
product using the bolts provided.
Packed with the heater is a heat shield to be fitted on the
underside of the product . After fitting the legs, fit the (Fig 1)
holes in the heat shield over the threaded ends that secure
the legs. Fasten the nuts over the heat shield to hold in place.
The primary air sealing plate is located on the front of the
grate. To locate in position, loosen the screws beneath the
grate and pull forward, then close the door fully, open again
and tighten the screws . (Fig 2)
Installing bricks and baffle
Before install the baffle plate and bricks, be sure to remove
the slotted log guard first otherwise baffle won’t fit through
door opening.
The baffle plate in the Westcott 1000 and 2000 models consist
of a steel retainer frame and a vermiculite board that sits in
the frame.
Position the rear vermiculite brick first positioning it below the
secondary burn tube. Fit the baffle plate (retainer and
vermiculite board) in the firebox. Hold the baffle plate up
while fitting the side vermiculite bricks and then rest the
baffle plate on top of the vermiculite side bricks.
To fit the log guard, there is a small square hole on each front
corner of the internal firebox that the legs on each end of the
log guard drop into to locate it.
Westcott 1000
Westcott 2000
2. ASSEMBLY OF THE HEATER

Product specificaties

Merk: Masport
Categorie: Heater
Model: Westcott 2000

Heb je hulp nodig?

Als je hulp nodig hebt met Masport Westcott 2000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Heater Masport

Masport

Masport Rubyvale Handleiding

2 Juli 2023
Masport

Masport R1500 Handleiding

21 Juni 2023
Masport

Masport Riverstone Handleiding

16 Juni 2023
Masport

Masport Pittsburgh MK II Handleiding

11 Juni 2023
Masport

Masport Adena Handleiding

2 Juni 2023
Masport

Masport Rockwood Handleiding

25 Mei 2023
Masport

Masport Westcott 2000 Handleiding

23 Mei 2023
Masport

Masport Westcott 1000 Handleiding

23 Mei 2023
Masport

Masport Redwood Handleiding

23 Mei 2023
Masport

Masport Klondike Handleiding

22 Mei 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Trisa

Trisa 9330.44 Handleiding

18 December 2024
Hortus

Hortus 211-413 Handleiding

18 December 2024
Yamazen

Yamazen HF-L122 Handleiding

18 December 2024
Yamazen

Yamazen HF-D121 Handleiding

18 December 2024
Yamazen

Yamazen HF-L121 Handleiding

18 December 2024
Universal Blue

Universal Blue UCRA9104-24 Handleiding

18 December 2024
Orava

Orava VL-203 Handleiding

18 December 2024
SHX

SHX HL20OSZ Handleiding

16 December 2024
Stanley

Stanley ST-125T-KFA-ES Handleiding

16 December 2024
Perel

Perel PHS2000 Handleiding

14 December 2024