Martha Stewart MTS-PS10 Handleiding

Martha Stewart Zaagmachine MTS-PS10

Lees hieronder de 📖 handleiding in het Nederlandse voor Martha Stewart MTS-PS10 (20 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/20
Model MTS-PS10 Form No. SJ-MTS-PS10-880E-M
OPERATOR’S MANUAL
ELECTRIC POLE CHAIN SAW
10IN | 7 AMP
© 2018 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
General Safety
mWARNING! When using electric yard tools, basic safety
precautions should always be followed to reduce the risk of
re, electric shock, and personal injury, including the following:
1. Keep guards in place – Protective guards should be
checked periodically to ensure they are properly tted and
in correct working order.
2. Remove adjusting keys and wrenches – Check that
adjusting wrenches are removed from the saw before
turning it on.
3. Keep work area clean and well-lit – Clear work area of
branches and limbs after each cutting session. Cluttered
areas invite accidents.
4. Do not use in dangerous environments – Do not use the
pole chain saw in damp or wet locations.
5. Do not use the pole chain saw in the rain.
6. Keep bystanders and children away – All bystanders,
including children and pets, should be kept a safe
distance away from the work area.
7. Do not force the tool – It will do the job eectively and
safely if it is used at the rate for which it was designed.
8. Use the right tool – Do not force the tool or any
attachment on the tool to do a job for which they were
not designed.
9. Wear proper apparel – Do not wear loose articles of
clothing or jewelry since such items may get caught
in moving parts. Use of heavy-duty rubber gloves,
substantial non-skid footwear, and close-tting clothing is
recommended when working outdoors with power tools.
10. Wear protective hair coverings to contain long hair.
11. Always wear safety glasses and ear defenders to
provide eye and ear protection – Everyday eyeglasses
only have impact resistant lenses and do not provide the
same protection as safety glasses.
12. Wear face or dust masks – If the cutting operation is
dusty, the use of a face or dust mask specially designed
to lter out microscopic particles is recommended.
13. Do not overreach – Keep proper footing and balance
at all times.
14. Maintain tools with care – Keep tools sharp and clean
for best and safest performance. Follow instructions for
lubricating and changing accessories.
15. Disconnect tool – Disconnect the pole chain saw from
the power supply when not in use, before servicing,
when transporting, or when changing the chain or other
accessories.
16. Reduce the risk of unintentional starting – Make sure
the switch is in the OFF position before plugging the tool
into a power source.
17. Use recommended accessories – Consult the owner’s
manual for recommended accessories. The use of
improper accessories may cause risk of injury.
18. Check for damaged parts – Before each use, repair or
replace any guard or part that is damaged. In addition,
check for alignment of moving parts, binding of moving
parts, breakage of parts, and any other conditions that
may aect the tool's operation.
19. Never leave tool unattended while it is running – Turn
the power OFF by removing the power cord directly from
its socket. Do not leave the saw until the cutting chain
comes to a complete stop.
20. Avoid unintentional starting – Do not carry the pole
chain saw with your nger on the switch.
21. Do not grasp the exposed cutting blade or cutting
edges when picking up or holding the saw – Be sure to
encase the cutting bar in its protective sheath when not
in use.
22. Stay alert – Watch what you are doing. Use common
sense. Do not operate the pole chain saw when you are
tired.
2
23. Store idle tool indoors – When not in use, appliances
should be stored indoors in a dry and high or locked-up
place out of the reach of children.
Electrical Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
the pole chain saw. Receptacles are available having
built-in GFCI protection and may be used for this
measure of safety.
2. To prevent electric shock, use only with an extension cord
suitable for outdoor use, such as SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to
use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
3. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
Use this appliance only with a polarized UL-, CSA-, or
ETL-rated extension cord for outdoor, all-weather use.
The appliance plug will t into a polarized extension
cord only one way.
If the appliance plug does not t fully into the extension
cord, reverse the plug. If the plug still does not t, obtain
a correct polarized extension cord. A polarized extension
cord will require the use of a polarized wall outlet. The
extension cord plug will t into the polarized wall outlet
only one way. If the plug does not t fully into the wall
outlet, reverse the plug. If the plug still does not t,
contact a qualied electrician to install the proper wall
outlet. Do not modify the appliance plug, extension cord
receptacle, or extension cord plug in any way.
4. To prevent the appliance cord from disconnecting from
the extension cord during operation, use the cord restraint
hook and/or make a knot with the two cords as shown in
Table 1.
5. Do not abuse the cord. Never pull the pole chain saw
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and
sharp edges.
m WARNING! m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the pole chain saw to make
contact with water while it is in operation. If the
appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA-, or ETL-rated extension cord
for outdoor, all-weather use.
• Do not use an extension cord over 100 ft (30 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
Up to 50 ft
(15 m)
16
+50 ft - 100 ft
(+15 m - 30 m)
14
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
3
Specic Safety Rules For
Pole Chain Saws
mWARNING! To protect yourself SHOCK HAZARD! –
from electrocution, do not operate the pole chain saw within
50 ft (15 m) of overhead wires. Failure to follow this instruction
could result in severe personal injury.
Operating Tips For Pole Chain Saws
• Stay alert. Use common sense while operating the unit.
• Keep work area clean and well-lit. Cluttered areas invite
accidents.
• Note the extension cord's location relative to the tool.
While operating the pole chain saw, be careful not to trip
over the cord.
• Keep the cord away from the chain and the operator at
all times.
• Keep children, animals, and bystanders a safe distance
away from the pole chain saw and extension cord.
• Only the pole chain saw operator should be in the
work area.
• Do not use the pole chain saw to cut down trees.
• Always use two hands when operating the pole chain saw.
Grip the pole chain saw securely with one hand on the
trigger, the other hand on the pole.
• Before starting the pole chain saw, make sure that the saw
chain is not in contact with any object.
• Do not allow the pole chain saw to make contact with
grounded objects such as pipes, fences, and metal posts.
• Keep all parts of the body away from the saw chain while
operating the pole chain saw.
• Do not force the pole chain saw while cutting. Apply light
pressure. It will perform more eectively and safely if it is
used at the rate for which it was designed.
• Use extreme caution when cutting a limb that is under
tension. When wood tension is released, the limb could
spring back and strike the operator, causing severe injury
or death.
• Do not carry a plugged-in unit. Carry the pole chain saw
from one place to another with the unit unplugged. During
transport, hold the pole at its balance point (close to the
saw end), with the guide bar and chain facing to the rear.
• Do not cut small brush and saplings with the pole chain
saw. Small branches may catch in the chain and be
whipped towards the operator, which could pull the
operator o balance.
Kickback
mWARNING! Kickback may occur when the nose or tip
of the guide bar touches an object, or when the wood closes in
and pinches the saw chain in the cut.
AVOID CONTACTING THE GUIDE BAR TIP WITH ANY
OBJECT. In some cases, when the tip makes contact with an
object, it may cause a fast reverse reaction, kicking the guide
bar up and back towards the operator. Pinching the saw chain
along the top of the guide bar may also push the guide bar
rapidly back towards the operator. Either of these reactions
may cause you to lose control of the pole chain saw, which
could result in serious personal injury.
• Kickback safety devices on this pole chain saw include
a skip chain and a low kickback guide bar. These will
reduce, but not entirely prevent, kickbacks. Follow the
necessary precautions indicated in this operator's manual
to avoid kickbacks.
• Always use two hands when operating the pole chain saw,
one hand gripping the trigger and the other hand gripping
the pole. Use a rm grip. Thumbs and ngers must wrap
around the trigger and the pole.
• Keep all guards in place on the pole chain saw. Make sure
they are in proper working order.
• Do not overreach or extend arms above shoulder height.
• Keep solid footing and balance at all times.
• Never try cutting through two branches at the same time.
Only cut one at a time.
• Do not bury the guide bar nose or try to cut by boring the
guide bar nose into the wood.
• Watch for shifting of wood or other forces that may pinch
the chain.
• Use extreme caution when re-entering a previous cut.
• Use the low-kickback chain and guide bar supplied with
this pole chain saw. Only use genuine Snow Joe® +
Sun Joe® replacement parts designed specically for use
with this pole chain saw.
• Never use a dull or loose chain. Keep the chain sharp with
proper tension.

Product specificaties

Merk: Martha Stewart
Categorie: Zaagmachine
Model: MTS-PS10

Heb je hulp nodig?

Als je hulp nodig hebt met Martha Stewart MTS-PS10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Martha Stewart

Martha Stewart

Martha Stewart MTS-PS10 Handleiding

12 Januari 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Ozito

Ozito PXBCS-1830 Handleiding

24 December 2024
Einhell

Einhell STP 500 E Handleiding

23 December 2024
Anova

Anova E60CS Handleiding

20 December 2024
Silverline

Silverline 447132 Handleiding

19 December 2024
Silverline

Silverline 427644 Handleiding

19 December 2024
Herkules

Herkules KS 210 Profi Handleiding

17 December 2024
Total

Total TS730301 Handleiding

16 December 2024
Total

Total TJSLI8501 Handleiding

16 December 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024
Bavaria

Bavaria BJS 400 Handleiding

5 December 2024