Martec Vapour Handleiding

Martec Heater Vapour

Lees hieronder de 📖 handleiding in het Nederlandse voor Martec Vapour (9 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

Please read these instructions carefully before installing and using the product. Keep the instructions handy for future reference. Electrical

wiring must only be done by a licensed electrician and a “Certificate of Compliance” must be issued on completion of the installation.

WH T’S IN THE BOXA

•Bathroom unit

•Operating and Installation Instructions.

•Wall plate and switch.

•1 x LED Light Panel

•Cutout emplateT

SAFETY INSTRUCTIONS

During use of the product, it is necessary to observe some precautions. Improper operation with disregard of precautions may result in infliction

of harm to health of the user and other people, as well as in infliction of damage to their property.

•Use only the voltage specified on the rating plate of the heater.

•This item should only be installed by a licensed tradesperson.

•The heater should be connected to the electric mains equipped with an automatic circuit breaker.

•The unit must be handled with care avoiding any sudden impacts or vibrations.

WARNING: FIRE RISK EXISTS IF THE HEATER IS COVERED BY OR POSITIONED CLOSE TO CURTAINS OR

OTHER COMBUSTIBLE MATERIALS.

•Do not use the appliance areas where gasoline, paint or other flammable liquids are used or stored.

•Do not use the appliance in particularly in dusty or where explosives are stored.

•Do not use the appliance in a building site, green house, barn or in animal stables.

•Do not use the appliance as a sauna heater.

•Do not use this unit in the place of animal propagating and rising.

•W o avoid burns, do not touch the appliance surface by hand and other body parts. It is also necessary to avoid touching the heater arming: T

whilst the appliance is switched on, as severe burns may result. The appliance can take up to 1 hour to cool down after switching it off.

•Do not place any items of clothing, hand towels or similar over the heater to dry. Risk of overheating and fire hazard.

•Do not leave the heater unattended whilst in use.

•Do not use this heater on a wet surface, or where it can fall or be pushed into water.

•Do not reach for an appliance that has fallen into water. Switch off at supply and unplug immediately.

•If the heater is defective, it must be checked and repaired by the manufacturer, its service agent or similarly qualified persons for repair.

•Do not operate appliance with wet hands.

•Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric

shock or injury.

•Do not use abrasive cleaning products on this appliance. If the body becomes dirty, wipe off dust with a cloth. Always remove plug from the

mains supply before cleaning.

ww .martecaustralia.com.au | 02 8778 7500 | sales@martecltd.com.auw Page 1 of 5

VAPOUR

Vapour 3-in-1 Fan Heater, Light and Exhaust

Installation Instructions

Model No: MBHV2000W

•The heater must be installed at least 1.8 m above the oor.

• The heater must not be located immediately below a socket outlet. The heater must not be located in front of a socket outlet. They

should be located outside the physical footprint of the units to minimize heat build up behind the heater.

• The standard power point must be installed by a licensed electrician.

• If the heater is to be mounted on an incline (eg. Sloping or angled ceiling), ensure the electrical connection is located at that lowest

point of the heater.

•Do not connect the appliance to the mains source until it has been installed in its nal location and adjusted to the position it will be

used in.

•Do not operate with the cord coiled up as this could cause a buildup of heat, which could pose a hazard.

• The use of an extension cord with this appliance is not recommended.

• Do not allow cord to come in contact with heated surfaces during operation.

• Do not run cord under carpeting, throw rugs or runners etc. Arrange cord away from areas where it is likely to be tripped over.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance

• The appliance is only intended for the purpose described in user manual.

• Do not use appliance or any part of the appliance out of the intended use to avoid risk.

• The use of attachments which are not recommended or sold by the appliance manufacturer may cause a risk of injury to persons

• CAUTION — some parts of this product can become very hot and cause burns. Particular attention has to be given where children

and vulnerable people are present.

•Install and operate the heater in strictly horizontal position on the ceiling or ceiling structural surface. The thermal resistance of the

ceiling coating and ceiling material should be at least 80 °C.

• WARNING: This heater is not equipped with a device to control the room temperature. The heater must not be within reach from

the oor, as severe burns may occur due to high surface temperatures. Do not use this heater in small rooms or where the room or

area is occupied by persons not capable of leaving the room on their own, persons who are unable to operate the heater safely and

with the guidelines of the use manual, unless constant supervision is provided.

• When the appliance is not in use and before cleaning, unplug the appliance from the outlet.

• To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water or other liquid.

• Household indoor/covered outdoor use only.

VAPOUR

Vapour 3-in-1 Fan Heater, Light and Exhaust

Installation Instructions

ww .martecaustralia.com.au | 02 8778 7500 | sales@martecltd.com.auw Page of 52

Model No: MBHV2000W

PRODUCT DIAGRAM AND SIZE

LOC TIONA

• The unit must be located and installed in accordance with AS/NZS 3000 and local building codes relating to damp situations.

• This may mean that no part of the Module may be located directly above any part of a bath or shower recess or enclosure.

•The unit should be installed in flat ceilings with a minimum height on 2 meters. At leas 200mm height clear ance in the ceiling cavity

is required to ensure sufficient ventilation for moisture to dis The unit must also be installed at least 250mm away from walls.perse.

• Ensure adequate air intake into the room exists through windows, vents or under the door to replace the displaced air from the

exhaust fan.

•Regulations concerning the discharge of air must be fulfilled.

POWER

AC220-240V ~50Hz electrical supply is required. The unit can be connected to a lighting or power circuit if loading permits. All

electrical work must be carried out in accordance with AS/NZS 3000 or latest edition thereof, and local building codes and

regulations. A five switch wall plate is included for all kinds of wiring combinations. Ensure the power supply is isolated before

commercing installation. Electrical wiring must only be done by a licensed electrical and a “Certificate of Compliance” contractor

must be issued at completion of the installation.

INS ALL TIONT A

VAPOUR

Vapour 3-in-1 Fan Heater, Light and Exhaust

Installation Instructions

ww .martecaustralia.com.au | 02 8778 7500 | sales@martecltd.com.auw Page 3 og 5

Model No: MBHV2000W

1. Use the cut out template card as a template. Place in the required

location and mark out the hole cutting size: 528mm x 345mm. Before

commencing cutting ensure that the area behind the intended

location is clear of all cables, pipes and joists. Once clear, cut out the

section along the previously marked lines.

2. Prise up the edge of fascia then take off the fascia. ake the LED T

plug ff the eater nit and remove cover of the terminal and connect o h u

the wires according to the diagram. Connect the ducting to the unit if

required.

3. Insert the unit into he ceiling cavity, ensuring the clips are resting

against the body of the unit. Tighten the screws to ensure the unit is

fixed securely.

4. Select the desired colour via the tricolour switch at the back of the

LED light. Connect the LED plug to the fascia and push the edge of

fascia towards the housing then let clips on fascia fix on the housing.

Product specificaties

Merk:	Martec
Categorie:	Heater
Model:	Vapour

Heb je hulp nodig?

Als je hulp nodig hebt met Martec Vapour stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Heater Martec

Martec Linear MBHL1000 Handleiding

16 November 2024

Martec MBHL1000W Handleiding

30 Januari 2024

Martec MBHT2000W Handleiding

22 Juni 2023

Martec MBHA800W Handleiding

19 Juni 2023

Martec Contour 2 Handleiding

18 Juni 2023

Martec Profile Panel 4 Handleiding

12 Juni 2023

Martec Phoenix Handleiding

9 Juni 2023

Martec Profile Panel 2 Handleiding

29 Mei 2023

Martec Forme 4 MBHF4LW Handleiding

27 Mei 2023

Martec Forme 2 MBHF2LW Handleiding

25 Mei 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Trisa 9330.44 Handleiding

18 December 2024

Hortus 211-413 Handleiding

18 December 2024

Yamazen HF-L122 Handleiding

18 December 2024

Yamazen HF-D121 Handleiding

18 December 2024

Yamazen HF-L121 Handleiding

18 December 2024

Universal Blue UCRA9104-24 Handleiding

18 December 2024

Orava VL-203 Handleiding

18 December 2024

SHX HL20OSZ Handleiding

16 December 2024

Stanley ST-125T-KFA-ES Handleiding

16 December 2024

Perel PHS2000 Handleiding

14 December 2024