Marshall MG10 Handleiding
Marshall
Gitaarversterker
MG10
Lees hieronder de 📖 handleiding in het Nederlandse voor Marshall MG10 (7 pagina's) in de categorie Gitaarversterker. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/7
From Jim Marshall
I would personally like to congratulate you on your purchase of this
next-generation Marshall MG amplifier.
As a musician myself, I fully understand what it takes to perform live in
a band situation. In addition to talent, dedication and a lot of hard work,
you also need equipment that does exactly what you ask of it. Over the
years I have witnessed many advances in amplifier technology and I
wanted this MG series to take full advantage of such innovations.
These solid-state amplifiers had to meet the tonal expectations of the
modern guitarist whilst also incorporating new and exciting digital
technology. With this goal firmly in mind, I set my experienced R&D
team the task of designing a new range of affordable MG amplifiers that
would not only produce the tone you’re looking for, but also offer an
intuitive and totally programmable way of customising, storing and
accessing your favourite Marshall tones and features.
Like all the amplifiers in the new MG range, state-of-the-art
manufacturing and stringent quality control procedures ensure that
these amplifiers meet the high standard of build you have come to
expect from all Marshall products.
Whether this is your first ever Marshall, or is the latest addition to your
arsenal of amps, the tone, flexibility and feel of these compact, rugged
units is guaranteed to deliver the goods – from bedroom, to backstage,
to on stage!
I wish you every success with your new Marshall. Welcome to the
family...
Yours Sincerely,
Dr. Jim Marshall OBE
MG15FX
1
MG30FX
2
Channel Selection
The amplifier has 4 channels - Clean, Crunch, OD1 &
OD2.
Pressing the Clean/Crunch switch (3) selects between
the Clean (Green Light) and Crunch (Red Light)
channels.
Pressing the OD switch (5) selects between the OD1
(Green Light) and OD2 (Red Light) channels.
When moving from an OD channel to a Clean/Crunch
channel, the unit remembers the last channel you were
in before leaving. E.g. If you have moved from the
Crunch Channel to an OD channel and you press the
Clean/Crunch switch (3), the amplifier will revert back to
the Crunch channel - rather than starting again in the
Clean channel.
Modes
The amplifier operates in two modes - Preset and
Manual.
To change between these two modes, you must hold
the Tap switch (10) down for at least two seconds.
When in manual mode the Store switch (12) lights red
and the selected channel light (3 or 5) will start to flash.
The amplifier will remember the last mode it was in after
power off and revert to it the next time it is powered on.
Preset
This is the factory default operation of the amplifier.
In Preset mode the position of all controls except
Master Volume (13) are stored within each channel.
Each channel should be considered a preset.
Selecting a channel automatically recalls the settings
stored within the channel. Note: The physical position of
the front panel controls, except Master Volume (13)
which is not storable, will now not match the actual
settings of the amplifier. All front panel switches will
automatically update.
Altering a control will cause the associated parameter to
jump to the current physical position of that control.
When a control is altered the selected channel light (3
or 5) will start to flash indicating that the current preset
has been altered.
To store the updated settings, push the Store switch
(12).
If you select another channel without pressing Store
(12) then any altered settings will be lost as the new
channel and its settings are recalled.
Manual
In manual mode the amp’s settings always match the
physical positions of the controls.
Changing channel only changes the channel, NO
presets are recalled, NO other controls are altered.
Pressing Store (12) will store the current settings into
the selected channel. These can then be recalled when
using the unit in Preset mode.
When channel settings have been stored the current
channel light (3 or 5) will stop flashing indicating the
preset has been saved.
Reverb & FX
The amplifier provides two simultaneous effects,
Reverb and one of four FXs (Chorus, Phaser, Flanger
or Delay)
Reverb
The Reverb control (8) sets the amount of signal sent to
the reverb section - allowing the reverb to spill between
channels as different presets are recalled. When the
Reverb control (8) is set to ‘0’ the reverb is switched off,
the status of the reverb is also indicated on the optional
footcontroller.
FX
The FX control is split into four segments and selects
the type of FX and adjusts its associated settings.
When the FX control is set to ‘0’ the FX are switched
off, the status of the FX is also indicated on the optional
footcontroller.
Tap Tempo
The Tap Tempo switch (10) is used for the Delay effect
only.
The Tap Tempo switch matches the delay time to the
time between two presses.
The Tap Tempo LED flashes red at the
selected/recalled delay time.
The number of repeats is reduced as the delay time
decreases.
If you change from a channel with delay to one without
delay the effect will spill between channels.
If you change from a channel with delay to a channel
with delay set to a different delay time the delay effect
will not spill between channels.
MP3 / Line In
The 3.5mm MP3 / Line In socket (14) allows the
connection of an external audio source e.g. MP3 or CD
player.
Headphones
The 3.5mm Headphones socket (16) allows the
connection of a pair of headphones. When a jack is
inserted into the headphones socket the unit’s speaker
is muted.
Power
The Power switch (17) turns the amplifier on and off. If
current settings have not been stored they will be lost.
MG15FX & MG30FX Overview
0
Chorus
Phaser
Flanger
Delay
FX Off
Speed increases and depth is reduced as
knob is turned clockwise.
Speed increases as knob is turned
clockwise.
Speed increases, feedback and depth are
reduced as knob is turned clockwise.
Delay level is increased as knob turned
clockwise.
Product specificaties
| Merk: | Marshall |
| Categorie: | Gitaarversterker |
| Model: | MG10 |
Heb je hulp nodig?
Als je hulp nodig hebt met Marshall MG10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Gitaarversterker Marshall
19 Juni 2023
14 Juni 2023
5 Juni 2023
22 Mei 2023
11 Mei 2023
11 Mei 2023
8 Mei 2023
3 Mei 2023
3 Mei 2023
29 April 2023
Handleiding Gitaarversterker
- Gitaarversterker Yamaha
- Gitaarversterker Ampeg
- Gitaarversterker Behringer
- Gitaarversterker Boss
- Gitaarversterker Fender
- Gitaarversterker Hartke
- Gitaarversterker Line 6
- Gitaarversterker Peavey
- Gitaarversterker Roland
- Gitaarversterker Orange
- Gitaarversterker Vox
- Gitaarversterker Harley Benton
- Gitaarversterker ART
- Gitaarversterker Valeton
- Gitaarversterker TC Electronic
- Gitaarversterker Radial Engineering
- Gitaarversterker Mooer
- Gitaarversterker Blackstar
- Gitaarversterker Electro Harmonix
- Gitaarversterker Markbass
- Gitaarversterker SPL
- Gitaarversterker Hughes & Kettner
- Gitaarversterker Laney
- Gitaarversterker Ashdown Engineering
- Gitaarversterker Bugera
- Gitaarversterker Palmer
- Gitaarversterker Empress Effects
- Gitaarversterker Dimavery
- Gitaarversterker Fishman
- Gitaarversterker AER
- Gitaarversterker EBS
- Gitaarversterker Rivera
- Gitaarversterker Suhr
- Gitaarversterker Two Notes
- Gitaarversterker GR Bass
- Gitaarversterker Voodoo Lab
- Gitaarversterker AMT
- Gitaarversterker DACS Audio
- Gitaarversterker DV Mark
- Gitaarversterker Budda
- Gitaarversterker API Audio
Nieuwste handleidingen voor Gitaarversterker
20 November 2024
20 November 2024
18 November 2024
18 November 2024
16 November 2024
16 November 2024
16 November 2024
15 November 2024
20 Oktober 2024
20 Oktober 2024