Makita TD090DZ Handleiding
Makita
Schroefmachine
TD090DZ
Lees hieronder de 📖 handleiding in het Nederlandse voor Makita TD090DZ (12 pagina's) in de categorie Schroefmachine. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
IMPORTANT: Read Before Using.
Cordless Impact Driver
TD090D
008813
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model TD090D
Machine screw 4 mm - 8 mm
Standard bolt 5 mm - 14 mm Capacities
High tensile bolt 5 mm - 10 mm
No load speed (min-1 ) 0 - 2,400
Impacts per minute 0 - 3,000
Overall length 155 mm
Net weight 0.92 kg
Rated voltage D.C. 10.8 V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
ï½¥ Read instruction manual.
ï½¥ Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2012/19/EU on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
ENE033-1
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
ENG905-1
Noise
The typical A-weighted noise level determined
according to EN60745:
Sound pressure level (L
pA) : 92 dB (A)
Sound power level (L
WA) : 103 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745:
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (ah) : 10.0 m/s2
Uncertainty (K) : 1.5 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
Cd
Ni-MH
Li-ion
3
ENH101-17
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Impact Driver
Model No./ Type: TD090D
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The Technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
31.12.2013
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A
moment of inattention while operating power tools
may result in serious personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.
Loose clothes, jewellery
or long hair can be caught in moving parts.
Product specificaties
Merk: | Makita |
Categorie: | Schroefmachine |
Model: | TD090DZ |
Gewicht: | 920 g |
Breedte: | 54 mm |
Diepte: | 155 mm |
Hoogte: | 178 mm |
Stroombron: | Batterij/Accu |
Oplaadtijd: | 0.8 uur |
Accu/Batterij voltage: | 10.8 V |
Stationair toerental (max): | 2400 RPM |
Opbergetui: | Ja |
Ingebouwd licht: | Ja |
Schroefdiameter: | 12 mm |
Maximale koppel (harde applicaties): | 90 Nm |
Vibratie emissie: | 1.5 m/s² |
Batterijtechnologie: | Lithium-Ion (Li-Ion) |
Heb je hulp nodig?
Als je hulp nodig hebt met Makita TD090DZ stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schroefmachine Makita
23 November 2024
23 November 2024
23 November 2024
21 Juni 2023
20 Juni 2023
19 Juni 2023
19 Juni 2023
18 Juni 2023
15 Juni 2023
12 Juni 2023
Handleiding Schroefmachine
- Schroefmachine Bosch
- Schroefmachine Panasonic
- Schroefmachine AEG
- Schroefmachine DeWalt
- Schroefmachine Basetech
- Schroefmachine Batavia
- Schroefmachine Bavaria
- Schroefmachine Black Decker
- Schroefmachine Bruder Mannesmann
- Schroefmachine Dremel
- Schroefmachine Easymaxx
- Schroefmachine Einhell
- Schroefmachine Elu
- Schroefmachine Fein
- Schroefmachine Ferm
- Schroefmachine Festool
- Schroefmachine Goon
- Schroefmachine Greenworks
- Schroefmachine Gude
- Schroefmachine Hikoki
- Schroefmachine Hitachi
- Schroefmachine Ingersoll Rand
- Schroefmachine Kawasaki
- Schroefmachine Kress
- Schroefmachine Laserliner
- Schroefmachine Maktec
- Schroefmachine Matrix
- Schroefmachine Metabo
- Schroefmachine Milwaukee
- Schroefmachine Parkside
- Schroefmachine Powerfix
- Schroefmachine Powerplus
- Schroefmachine Ryobi
- Schroefmachine Silverline
- Schroefmachine Skil
- Schroefmachine Stanley
- Schroefmachine Toolcraft
- Schroefmachine Toolland
- Schroefmachine Trotec
- Schroefmachine Velleman
- Schroefmachine Vonroc
- Schroefmachine Westfalia
- Schroefmachine Wiha
- Schroefmachine Worx
- Schroefmachine Omega
- Schroefmachine Ozito
- Schroefmachine Black And Decker
- Schroefmachine Steren
- Schroefmachine Urrea
- Schroefmachine Cocraft
- Schroefmachine Meec Tools
- Schroefmachine Senco
- Schroefmachine Genesis
- Schroefmachine Hilti
- Schroefmachine Facom
- Schroefmachine Kraftwerk
- Schroefmachine EMOS
- Schroefmachine Cotech
- Schroefmachine Power Craft
- Schroefmachine Tacklife
- Schroefmachine Truper
- Schroefmachine Fieldmann
- Schroefmachine Mafell
- Schroefmachine Carrera
- Schroefmachine Biltema
- Schroefmachine Porter-Cable
- Schroefmachine Beta
- Schroefmachine Dedra
- Schroefmachine MSW
- Schroefmachine Sthor
- Schroefmachine Craftsman
- Schroefmachine Chamberlain
- Schroefmachine Chicago Pneumatic
- Schroefmachine Alpha Tools
- Schroefmachine Hazet
- Schroefmachine Yato
- Schroefmachine Total
- Schroefmachine Abac
- Schroefmachine Meister Craft
- Schroefmachine StarTech.com
- Schroefmachine Park Tool
- Schroefmachine Pansam
- Schroefmachine Gedore
- Schroefmachine Netter Vibration
- Schroefmachine SW-Stahl
- Schroefmachine Cleco
- Schroefmachine Einhell Bavaria
- Schroefmachine Prowork
- Schroefmachine Proviel
- Schroefmachine Weidmüller
- Schroefmachine Wera
- Schroefmachine Rodcraft
- Schroefmachine Bavaria By Einhell
- Schroefmachine TAURUS Titanium
Nieuwste handleidingen voor Schroefmachine
16 December 2024
16 December 2024
16 December 2024
9 December 2024
8 December 2024
5 December 2024
5 December 2024
5 December 2024
4 December 2024