Makita DCS540 Handleiding
Makita
Kettingzagen
DCS540
Lees hieronder de 📖 handleiding in het Nederlandse voor Makita DCS540 (64 pagina's) in de categorie Kettingzagen. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/64
1
Owner’s and Safety Manual
for Gasoline Chain Saws (page 2 - 32)
Manuel d’emploi et de sécurité
de tronçonneuses thermiques (page 33 - 63)
WARNING!
Read and understand this Manual. Always follow safety precautions in the Owner’s and Safety Manual.
Improper use can cause serious injury!
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Preserve this Manual carefully!
ATTENTION!
Suivez toujours les conseils de sécurité du présent manuel d’emploi et de sécurité. Une utilisation
incorrecte de la tronçonneuse peut entraîner des blessures graves! Conservez avec soin ce manuel!
Les gaz d’échappement émis par ce produit contiennent des produits chimiques connus par l’Etat de
Californie pour provoquer le cancer, des défauts de naissance ou autres dommages de reproduction.
Lisez et comprenez ce manuel.
DCS430, DCS431
DCS520, DCS520i
DCS540
DCS5200, DCS5200i
2
EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE
MAKITA U.S.A, Inc warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built,
and equipped to conform at the time of initial sale to all applicable regulations of the U.S.
Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause
this engine to fail to conform with EPA regulations during its warranty period.
For the components listed under PARTS COVERED, the service dealer authorized by MAKITA will, at no cost to you, make the
necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.
EMISSION COMPONENT DEFECT WARRANTY PERIOD
The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.
PARTS COVERED
Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require
scheduled maintenance and are warranted up to the first scheduled replacement point for that part.
Fuel Metering System Ignition System
Carburetor and internal parts Spark plugs
Fuel filter, if applicable Flywheel Magneto
Throttle stopper, if applicable Ignition Coil
Choke System, if applicable
Air Induction System Miscellaneous Items Used in Above Systems
Pre filter, if exist Fuel hoses, clamps and sealing gaskets
Air filter, Air cleaner case, Intake manifold
OBTAINING WARRANTY SERVICE
To obtain warranty service, take your engine to the nearest MAKITA Factory Service Center or service Center authorized by
MAKITA. Bring your sales receipts indicating date of purchase for this engine. The dealer of service authorized by MAKITA will
perform the necessary repairs or adjustments within a reasonable amount of time and furnish you with a copy of the repair order.
All parts and accessories replaced under this warranty become the property of MAKITA.
WHAT IS NOT COVERED
• Conditions resulting from tampering, misuse, improper adjustment (unless they were made by the service dealer authorized by
MAKITA during a warranty repair), alteration, accident, failure to use the recommended fuel and oil, or not performing required
maintenance services.
• The replacement parts used for required maintenance services.
• Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.
• Diagnosis and inspection charges that do not result in warranty-eligible service being performed.
• Any non-authorized replacement part, or malfunction of authorized parts due to use of non-authorized parts.
OWNER’S WARRANTY RESPONSIBILITIES
As the engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual.
MAKITA recommends that you retain all receipts covering maintenance on your engine, but MAKITA cannot deny warranty solely
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the engine owner, you should
however be aware that MAKITA may deny warranty coverage if your engine or a part has failed due to abuse, neglect, improper
maintenance or unapproved modifications.
You are responsible for presenting your engine to the nearest service dealer authorized by MAKITA when a problem exists.
If you have any questions regarding your warranty rights and responsibilities, you should contact the MAKITA Warranty service
Department at 1-888-OPE-PART for the information.
THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM WARRANTY:
MAINTENANCE AND REPAIRS
You are responsible for the proper maintenance of the engine. You should keep all receipts and maintenance records covering the
performance of regular maintenance in the event questions arise. These receipts and maintenance records should be transferred
to each subsequent owner of the engine. MAKITA reserves the right to deny warranty coverage if the engine has not been properly
maintained. Warranty claims will not be denied, however, solely because of the lack of required maintenance or failure to keep
maintenance records.
MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY
ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A SERVICE
DEALER AUTHORIZED BY MAKITA. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY
TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A
BEARING ON THE OUTCOME OF A WARRANTY CLAIM.
If other than the parts authorized by MAKITA are used for maintenance replacements or for the repair of components affecting
emission control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to the parts
authorized by MAKITA in their performance and durability.
HOW TO MAKE A CLAIM
All repair qualifying under this limited warranty must be performed by a service dealer authorized by MAKITA. In the event that any
emission-related part is found to be defective during the warranty period, you shall notify MAKITA Warranty service Department at
1-888-OPE-PART and you will be advised of the appropriate warranty service dealer or service providers where the warranty repair
can be performed.
3
The MAKITA DCS430, DCS431, DCS520, DCS520i, DCS540, DCS5200, DCS5200i will be delivered in a
protective cardboard box to prevent transport damage. Cardboard is a basic raw material and is consequently
reuseable or suitable for recycling (waste paper recycling).
WARNING !
Careless or improper use of this product can cause serious or even fatal injury.
Before operating a chain saw or other MAKITA products it is important that you read, fully understand and
carefully follow the instructions outlined in this owners manual. Kickback may cause severe or fatal injury and
is one of many potential dangers in operating a chain saw. Kickback and other safety related precautions are
described in detail within this owners manual. Additional owners manuals are available from MAKITA U.S.A.,
INC., 14930-C Northam Street, La Mirada, CA 90638-5753, USA, Telephone: (714) 522 80 88 and MAKITA
CANADA INC.,1950 Forbes Street, Whitby, Ontario, L1N 7B7, Canada, Telephone: (905) 571 22 00.
RE Y
Contents Page
Delivery inventory 4
Symbols 4
Safety precautions 5-16
Denomination of components 17
Technical data 18
Approved bar and chain combinations 18
Mounting the guide bar and saw chain 19-20
Chain brake 20
Fuel / Refuelling 21-22
Adjusting the chain lubrication 22
Starting the engine 23
Stopping the engine 23
Checking the chain brake 24
Checking the chain lubrication 24
Adjusting the carburetor 24
Working in winter 25
Contents Page
Sharpening the saw chain 25-26
Cleaning the guide bar 26
Cleaning the brake band and sprocket interior 27
Replacing the saw chain 27
Replacing the fuel filter 27
Replacing / cleaning the spark arrester screen 27
Cleaning the air filter 28
Replacing the spark plug 28
Replacing the starter cable 29
Replacing the return spring 29
Mounting the fan housing 29
Instructions for daily and periodic maintenance 30
Service, spare parts and guarantee 30-31
Troubleshooting 31
Extract from the spare parts list 32
Adress list 64
DCS430, DCS431, DCS520, DCS520i, DCS540, DCS5200, DCS5200i
This product complies with: American National Standard Institute B 175.1-1991 chain saw safety standard.
Canadian Standards Association Z62.1-95 chain saw safety standard.
Z62.3-96 chain saw kickback standard.
Society of Automotive Engineers SAEJ 335-Jun 95 „Multiposition small
engine exhaust system fire ignition
suppression”
With the purchase of this chain saw you have chosen a German quality product. Important instructions for the
assembly and operation of this saw are given in this manual. For your own safety, we ask you to read the accident
prevention instructions very carefully before putting your chain saw into operation, as incorrect handling can,
despite all precautions, lead to accidents. With a little care and attention you will have good service and lasting
satisfaction from this first-rate product. The following industrial property rights apply: US 4465440, US 5411382,
EP 0236858, EP 0560201, GBM 8710075, GBM 8809928, GBM 9203378, GBM 29616652.
Product specificaties
| Merk: | Makita |
| Categorie: | Kettingzagen |
| Model: | DCS540 |
Heb je hulp nodig?
Als je hulp nodig hebt met Makita DCS540 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kettingzagen Makita
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
Handleiding Kettingzagen
- Kettingzagen Alpina
- Kettingzagen Dolmar
- Kettingzagen Einhell
- Kettingzagen Hitachi
- Kettingzagen Husqvarna
- Kettingzagen McCulloch
- Kettingzagen Metabo
- Kettingzagen Remington
- Kettingzagen Ryobi
- Kettingzagen Sachs Dolmar
- Kettingzagen Solo
- Kettingzagen Sterwins
- Kettingzagen Stiga
- Kettingzagen Stihl
- Kettingzagen Tanaka
- Kettingzagen Worx
- Kettingzagen Ozito
- Kettingzagen Black And Decker
- Kettingzagen Ronix
- Kettingzagen Meec Tools
- Kettingzagen Cobra
- Kettingzagen Black Max
- Kettingzagen MacAllister
- Kettingzagen Nakayama
- Kettingzagen Poulan
- Kettingzagen Craftsman
- Kettingzagen Qualcast
Nieuwste handleidingen voor Kettingzagen
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022
4 Oktober 2022