Makita 6805BV Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Makita 6805BV (32 pagina's) in de categorie Schroefmachine. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/32
GB
Screwdriver Instruction Manual
F
Visseuse Manuel d’Instructions
D
Schrauber Betriebsanleitung
I
Avvitatrice Istruzioni d’Uso
NL
Schroevedraaier Gebruiksaanwijzing
E
Atornillador Manual de Instrucciones
P
Aparafusadora Manual de Instruço˜ es
DK
Skruemaskine Brugsanvisning
S
Momentskruvdragare Bruksanvisning
N
Skrutrekker Bruksanvisning
SF
Ruuvinväännin Käyttöohje
GR ∫·ÙÛ·‚›‰È √‰ËÁ›Â˜ ÃÚ‹Ûˆ˜
6805BV
1 2
3 4
5 6
7
2
ENGLISH Explanation of general view
1Front cap
2Locator
3Pointer
4Adjusting ring
5Low
6High
7Speed control screw
8Switch trigger
9Lock button
0Reversing switch lever
SPECIFICATIONS
Model 6805BV
Capacities
Self drilling screw .......................................... 6 mm
Machine screw .............................................. 8 mm
Wood screw ............................................... 6.2 mm
Bit shank size ............................................. 1/4’’ Hex
No load speed (RPM) ................................ 0 2,500
Overall length ............................................... 267 mm
Net weight ....................................................... 1.9 kg
Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
These symbols mean:
Read instruction manual.
DOUBLE INSULATION
ADDITIONAL SAFETY RULES
1. Always be sure you have a firm footing.
Be sure no one is below when using the
machine in high locations.
2. Hold the machine firmly.
3. Keep hands away from rotating parts.
4. When driving into walls, floors or wherever
live’ electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE
MACHINE!
Hold the machine by the insulated grasping
surfaces to prevent electric shock if you drive
into a ‘‘live’’ wire.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Removing or installing the bit (Fig. 1)
Important:
Always be sure that the machine is switched off and
unplugged before removing or installing the bit.
To remove the bit, first pull the front cap off and then
pull the bit firmly. To install the bit, insert it into the
machine as far as it will go and then replace the front
cap.
Depth adjustment (Fig. 2, 3 & 4)
When you wish to drive self drilling screws, etc.,
adjust the depth as follows.
Turn the locator to adjust the depth.
Initially, adjust the locator to create a distance of
approximately 1 mm from the tip of the front cap
(which works in conjunction with the locator) to the
base of the screw head. One full turn of the locator
equals 1 mm change in depth. After adjusting the
locator, turn the adjusting ring so that the 6 mark is
aligned with the pointer on the gear housing. Drive a
trial screw into your material or a piece of duplicate
material. If the depth is not suitable for the screw,
continue adjusting until the proper depth setting is
obtained.
Adjusting fastening torque (Fig. 5)
When you wish to drive machine screws, wood
screws, hex bolts, etc. with the predetermined torque,
adjust the fastening torque as follows.
The fastening torque may be adjusted by turning the
adjusting ring. Before turning the adjusting ring, turn
the locator in the direction of the arrow as far as it will
go without forcing. The torque is increased by turning
the adjusting ring in the direction of the arrow and
decreased by turning it in the opposite direction. Align
the number 1 on the adjusting ring with the pointer on
the gear housing. Drive a trial screw into your material
or a piece of duplicate material. If the fastening torque
is not suitable for the screw, continue adjusting until
the proper torque is obtained.
CAUTION:
The adjusting ring should be turned only within the
numbered range. It should not be forced beyond this
range.
3


Product specificaties

Merk: Makita
Categorie: Schroefmachine
Model: 6805BV

Heb je hulp nodig?

Als je hulp nodig hebt met Makita 6805BV stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Schroefmachine Makita

Handleiding Schroefmachine

Nieuwste handleidingen voor Schroefmachine