Makita 6407 Handleiding

Makita Schroefmachine 6407

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita 6407 (36 pagina's) in de categorie Schroefmachine. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/36

Drill Instruction Manual

Perceuse Manuel d’Instructions

Bohrmaschine Betriebsanleitung

Trapano Istruzioni d’Uso

Boormachine Gebruiksaanwijzing

Taladro Manual de Instrucciones

Berbequim Manual de Instruço˜ es

Boremaskine Brugsanvisning

Borrmaskin Bruksanvisning

Boremaskin Bruksanvisning

Porakone Käyttöohje

GR ∆Ú˘¿ÓÈ √‰ËÁ›Â˜ ÃÚ‹ÛÂˆ˜

6407

6408

6407

6408

1 2

3 4

ENGLISH Explanation of general view

1Chuck

2Chuck key

3Tighten

4Sleeve

5Ring

6Switch trigger

7Lock button

8Reversing switch lever

SPECIFICATIONS

Model 6407/6408

Drilling capacities

Steel ............................................................ 10 mm

Wood ........................................................... 25 mm

No load speed (RPM) ................................ 0 – 2,500

Overall length ............................................... 261 mm

Net weight ....................................................... 1.4 kg

•Due to the continuing program of research and

development, the speciﬁcations herein are subject

to change without prior notice.

•Note: Speciﬁcations may diﬀer from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, and can only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed

safety instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Always be sure you have a ﬁrm footing.

Be sure no one is below when using the

machine in high locations.

2. Hold the machine ﬁrmly.

3. Keep hands away from rotating parts.

4. When drilling into walls, ﬂoors or wherever

‘‘live’’ electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE!

Hold the machine by the insulated grasping

surfaces to prevent electric shock if you drill

into a ‘‘live’’ wire.

5. Do not leave the machine running. Operate the

machine only when hand-held.

6. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing drill bit

Important:

Always be sure that the machine is switched oﬀ and

unplugged before installing or removing the bit.

For 6407 (Fig. 1)

To install the bit, place it in the chuck as far as it will

go. Tighten the chuck by hand. Place the chuck key in

each of the three holes and tighten clockwise. Be sure

to tighten all three chuck holes evenly.

To remove the bit, turn the chuck key counterclock-

wise in just one hole, then loosen the chuck by hand.

After using the chuck key, remember to return it to the

chuck key holder.

For 6408 (Fig. 2)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far

as it will go. Hold the ring ﬁrmly and turn the sleeve

clockwise to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve

counterclockwise.

Switch action (Fig. 3)

CAUTION:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

To start the machine, simply pull the trigger. Machine

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. For continuous

operation, pull the trigger and then push in the lock

button. To stop the machine from the locked position,

pull the trigger fully, then release it.

Reversing switch action (Fig. 4)

CAUTION:

•Always check the direction of rotation before drilling.

•Use the reversing switch lever only after the

machine comes to a complete stop. Changing the

direction of rotation before the machine stops may

damage the machine.

This machine has a reversing switch to change the

direction of rotation. Move the reversing switch lever

to the position for clockwise rotation or the posi-

tion for counterclockwise rotation.

Product specificaties

Merk:	Makita
Categorie:	Schroefmachine
Model:	6407
Kleur van het product:	Blauw
Gewicht:	1406 g
Breedte:	261 mm
Gewicht verpakking:	1814 g
Stroombron:	AC
Input vermogen:	- W
Stationair toerental (max):	2500 RPM
Boor diameter in staal (max):	- mm
Boor diameter in beton (max):	10 mm
Boor diameter in hout (max):	25 mm
Boorhouder:	Sleutel
Aanpasbare snelheid:	Ja
Boorstift inbegrepen:	Ja
Geluidsvermogensniveau:	79 dB