Majestic SCCMPPT40 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Majestic SCCMPPT40 (34 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/34
MPPT Series
Maximum Power Point Tracking
SCCMPPT20 SCCMPPT30 SCCMPPT2440— —
Solar Charge and Discharge Controller User Manual
Model
SCCMPPT 20
SCCMPPT 30
SCCMPPT 40
Battery voltage
12V/ 24V
Max. solar panel voltage
100V (25°C), 90V (-25°C)
Charging current
20A
30A
40A
Discharging current
20A
Dear users,
Thank you for choosing our product!
Safety Instructions
1. As this controller deals with voltages that exceed the top limit for human safety, do not
operate it before reading this manual carefully and completing safety operation training.
2. The controller has no internal components that need maintenance or service, thus do
not attempt to disassemble or repair the controller.
3. Install the controller indoors, and avoid component exposure and water intrusion.
4. During operation, the heatsink may reach a very high temperature, therefore install the
controller at a place with good ventilation conditions.
5. It's recommended that a fuse or circuit breaker be installed outside the controller.
6. Before installing and wiring the controller, make sure to disconnect the photovoltaic
array and the fuse or breaker close to the battery terminals.
7. After installation, check if all connections are solid and reliable so as to avoid loose
connections that may give rise to dangers caused by heat accumulation.
Warning: means the operation in question is dangerous, and you
should get properly prepared before proceeding.
Note: means the operation in question may cause damage.
Tips: means advice or instruction for the operator.
Table of Contents
1. Product Introduction ................................................................................................................ 4
1.1 Product Overview ............................................................................................................ 4
1.2 Product Features .............................................................................................................. 4
1.3 Exterior and Interfaces ..................................................................................................... 6
1.4 Introduction to Maximum Power Point Tracking Technology ........................................ 7
1.5 Charging Stages Introduction ........................................................................................ 10
2. Product Installation ................................................................................................................ 13
2.1 Installation Precautions .................................................................................................. 13
2.2 Wiring Specications ..................................................................................................... 14
2.3 Installation and Wiring .................................................................................................. 15
3. Product Operation and Display .............................................................................................. 19
3.1 LED Indicators ............................................................................................................... 19
3.2 Key Operations .............................................................................................................. 21
3.3 LCD Startup and Main Interface ................................................................................... 22
3.4 Load Mode Setting Interface ......................................................................................... 23
3.5 System Parameter Settings ............................................................................................ 24
4. Product Protection Function and System Maintenance ......................................................... 26
4.1 Protection Functions ...................................................................................................... 26
4.2 System Maintenance ...................................................................................................... 27
4.3 Abnormality Display and Warnings ............................................................................... 28
5. Product Specication Parameters .......................................................................................... 29
5.1 Electric Parameters ........................................................................................................ 29
5.2 Battery Type Default Parameters (parameters set in monitor software) ....................... 30


Product specificaties

Merk: Majestic
Categorie: Niet gecategoriseerd
Model: SCCMPPT40

Heb je hulp nodig?

Als je hulp nodig hebt met Majestic SCCMPPT40 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Majestic

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Smeg

Smeg GTA-6 Handleiding

21 November 2024
Smeg

Smeg KIT6CX Handleiding

21 November 2024
Senal

Senal SCS-98 Handleiding

21 November 2024
Senal

Senal ASM-6 Handleiding

21 November 2024
Senal

Senal ASM-MNTKIT Handleiding

21 November 2024
Senal

Senal SMS-45 Handleiding

21 November 2024
Smeg

Smeg KIT6PX Handleiding

21 November 2024
Senal

Senal SCI-3212MP Handleiding

21 November 2024
Senal

Senal OLM-2S-P Handleiding

21 November 2024