Lucide Saxen 40202/02/11 Handleiding

Lucide Lamp Saxen 40202/02/11

Lees hieronder de đź“– handleiding in het Nederlandse voor Lucide Saxen 40202/02/11 (13 pagina's) in de categorie Lamp. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/13
Line drawing of the item
Item number: 40202/02/11
Technical details
Materials used: M +etal
F abric
Color: Chrome+Black shade
Dimmable and how is fixture dimmable No
Size: Height: 66cm
Length: 27cm
Width: 23.5cm
Net weight: 60. kg
Power requirements: -220 240v~50Hz
Bulb type and maximum wattage: E27 Max.60W + LED Max.3W
Number of bulbs: + 1xE27 1pc LED
IP degree:
IP20
27cm
23.5cm
20cm
34cm
MAX 66cm
15.5cm
Installation drawing
L
N
Safety Instructions
Please read this notice carefully and keep it all along the use of this product. Follow the instructions for a safe and correct
installation and functioning of the fitting. The manufacturer does not accept any responsibility for damage caused by improper
installation and service. Installation should always be done by qualified electrician.
Always isolate the power before commencing installation, maintenance or repair.
In case of doubts, please contact a qualified electrician.
Please pay attention to locations where the item can be installed (indoor, outdoor, bathroom (for outdoor and bathroom installation,
please see further). Indoor items cannot be used in humid places. Do not put in contact with water or any liquids or the item
inflammable products. Always respect the minimal distance (indicated on the light) to inflammable products.
During installation, make sure that the cables will not be squeezed or damaged by sharp edges. If the external flexible cable is
damaged, it needs to be replaced exclusively by the manufacturer, his service agent, or another qualified electrician. This to avoid is
all risks.
Because the temperature of the bulbs can get very high, they must cool down before being touched. Always use the the item and
correct bulb (respect type and maximal wattage as indicated on the product ).
Installation of items in bathroom:
Since each country has its own regulations, please check
them with qualified people, before installing lighting products
in the bathroom.
Below we will explain general requirements.
Zone 0: At least IPX7, and a voltage level according to SELV
is allowed in this zone. SELV means “security extra low
voltage”. In general, this means maximum 12V. We
recommend that the lights are installed by a qualified
electrician in this zone.
Zone 1: At least IPX4, Only lighting fixtures with an IP of
minimum IPX4 and a voltage level according to SELV is
allowed in this zone. We recommend that the lights are
installed by a qualified electrician in this zone.
Zone 2: At least IP44. If items are not low voltage, then they
need to be installed at a height of at least 1.6m.
Zone 3: This zone includes all the space which is not mentioned in the 3 other zones (0, 1 and 2). As long as the water can not spat
on the lighting or steam can not get fixated on the light, then an IP21 is ok.
Specific remarks:
If the bottom of the basin for bath or shower is higher than 15cm from the ground, then the heights need to be calculated from the
bottom of the basin.
If there is no basin then the height for zone 0 is 10cm.
In the Netherlands the height of 225cm for zones 1 and 2 is replaced by 260cm.
Symbol Explanation of the symbols which can appear on the fixture
This item is only suitable for indoor use, exclusive bathroom (except if a higher IP degree permits
that the item can be used in the bathroom).
Legislation requires that all electrical and electronic equipment must be collected for reuse and
recycling. Electrical and electronic equipment marked with this symbol indicating separate
collection of such equipment must be returned to a municipal waste collection point.
Please respect the minimum distance from the bulb to inflammable objects.
Class I: The item has an earth connection. The earth wire (green yellow) needs to be connected to -
the earth connection (marked with this symbol).
Class II: The item is double insulated and must not be connected to the earth wire.
Class III: The item is only suitable for lower voltage supply and must not be connected to the earth
wire.
If the protection glass is damaged or broken, it needs to be replaced immediately.

Product specificaties

Merk: Lucide
Categorie: Lamp
Model: Saxen 40202/02/11

Heb je hulp nodig?

Als je hulp nodig hebt met Lucide Saxen 40202/02/11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Lamp Lucide

Lucide

Lucide Baskett 45459/04/30 Handleiding

22 November 2024
Lucide

Lucide Tycho 45474/06/30 Handleiding

22 November 2024
Lucide

Lucide Knulle 45504/01/31 Handleiding

22 November 2024
Lucide

Lucide Gitta 47500/81/17 Handleiding

22 November 2024
Lucide

Lucide Greasby 47502/81/36 Handleiding

22 November 2024
Lucide

Lucide Ramzi 47506/81/43 Handleiding

22 November 2024
Lucide

Lucide Sytze 48750/30/72 Handleiding

22 November 2024
Lucide

Lucide Reda 78599/01/30 Handleiding

22 November 2024
Lucide

Lucide Otis 79198/32/61 Handleiding

22 November 2024
Lucide

Lucide Chimney 09926/02/30 Handleiding

22 November 2024

Handleiding Lamp

Nieuwste handleidingen voor Lamp

JBL

JBL Partylight Beam Handleiding

20 November 2024
HQ Power

HQ Power HQRL45007 Handleiding

18 November 2024
Heitronic

Heitronic 35113 Handleiding

17 November 2024
Livarno Lux

Livarno Lux IAN 66760 Handleiding

17 November 2024
Livarno Lux

Livarno Lux LTL 20 A2 Handleiding

17 November 2024
Livarno Lux

Livarno Lux 1241/022L+1242/022L Handleiding

17 November 2024
Livarno Lux

Livarno Lux 7594-010L Handleiding

17 November 2024
Livarno Lux

Livarno Lux 7596-010L Handleiding

17 November 2024
Dorr

Dorr SLR-16 Handleiding

17 November 2024
Eurolite

Eurolite TMH BSW-380 Handleiding

16 November 2024