Lowell OS-150TB Handleiding

Lowell Speaker OS-150TB

Lees hieronder de 📖 handleiding in het Nederlandse voor Lowell OS-150TB (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTALLATION SHEET FOR

0S-150TB AND OS-150TW

150 WATT INDOOR/OUTDOOR SPEAKERS

Instruction Sheet

IS-OS150

Issued 1-: 13-16

Lowell Manufacturing Company 100 Integram Drive Pacific, Missouri 63069 U.S.A.

Call: 800-325-9660 Fax: 636-257-6606 Click: www.lowellmfg.com

The OS-150TW (white and OS-150TB (black speakers may be mounted indoors ) )

or protected (covered outdoors The models are identical except for color In this ) . .

installation sheet the speaker will be referred to simply as the OS-150T The front , .

of the speaker (See Figure 1 is protected with an aluminum fine mesh grille with a )

weather resistant scrim material behind the grille. The speaker and grille may be

wiped down for cleaning but the use of a power washer or other high pressure ,

cleaning equipment will void the speaker’s warranty. The rear of the speaker (See

Figure 2 includes a U-bracket and an input selector switch. )

MECHANICAL SPECIFICATIONS

Complete OS-150T weight: . lbs. (8.165 18 0 Kg.)

Enclosure: Weather-resistant UV-resistant talc impregnated polypropylene.

Front Grille: Weather-resistant UV-resistant powder coat painted aluminum.

U-Bracket Weather-resistant plated and powder coat painted steel.:

ELECTRICAL SPECIFICATIONS

Power Rating: 150W RMS (RS426B test procedure).

Frequency Response: 65Hz- kHz + 620 dB

Sensitivity: 91.0dB log average SPL (at ohms @1W/1M8 )

Woofer: 8" polymer coated paper composite cone with cloth surround.

HF Compressions Driver: Titanium diaphragm with 1 voice coil ferrite magnet." &

Impedance: 8-ohms nominal (minimum impedance 8. ohms 6 @ 274 Hz).

Input: Screw terminals capable of attaching (2 #12 stranded conductors.–)

22 86. cm

INPUT SELECT SWITCH - TRANSFORMER TAP SETTINGS

TAP

25 70V LINE V LINE

7.5W

100V LINE

3.8W

1.9W

. W94

60W

30W

15W

7.5W

60W

DO NOT USE

30W

15W

8-ohm switch position bypasses the transformer.

E . W 3.8W 7.5W48

16"

40 64. cm

10 25" / .4cm (as shipped from factory)

11" / . cm (using alternate bracket holes)27 94

16.3"

41 40. cm

2" / 5.08cm

8.3"

21 08. cm

Dispersion: 80o vertical X 80o

horizontal conical dispersion (-6dB down at 2kHz).

FIGURE 1

FIGURE 2

Instruction Sheet

IS-OS150

Issued 1- -: 13 16

Lowell Manufacturing Company 100 Integram Drive Pacific, Missouri 63069 U.S.A.

Call: 800-325-9660 Fax: 636-257-6606 Click: www.lowellmfg.com

The OS-150T includes a heavy steel plated and powder coat painted

U-bracket that allows the OS-150T to be mounted vertically (See Figure 3 or )

horizontally (See Figure 4). Only install the OS150T in a protected (covered)

outdoor location and tilt the speaker slightly downward to prevent moisture

from collecting in the drivers. The U-bracket includes a 5/8 diameter center "

hole that may be used to route the speaker cable into the wall. The bracket

also includes vertical and horizontal mounting slots that make it possible to

secure the mounting bolts to the wall and then slide the bracket over those

bolts to hang the speaker (See Figure 5). Be sure to securely tighten the bolts

after the speaker is in place. Some installers prefer to remove the bracket and

mount it to the wall first. That makes it easy to lift the speaker and attach it to

the bracket by replacing the bracket knobs.

The two angle adjustment knobs may be removed and then refastened

through the optional mounting holes in the U-bracket to allow horizontal shelf

mounting with the maximum downward tilt angle of 40 degrees down from

horizontal (See Figure 6).

Speaker Mounting:

SAFETY NOTICE: Speaker installation should only be performed by experienced

qualified professionals with knowledge of the proper load-rated hardware and

safe mounting and rigging techniques. The speaker system must be mounted in

accordance with all local, state and federal codes and regulations and the ,

installation must conform to industry standard practices. It is the responsibility

of the installer to consult a licensed mechanical or structural engineer to

evaluate and certify the structural integrity and safety of any mounting method

before installation. Lowell Manufacturing is not responsible for the use misuse, ,

or misapplication of this loudspeaker product.

The optional U-bracket mounting holes can also be used to mount the speaker

in the vertical orientation (so the speaker can be adjusted horizontally to the

right or left but by attaching the top knob to the furthest hole from the rear of )

the bracket and by attaching the bottom knob to the closest hole in the bracket

(See Figure 7) an automatic degree downward tip of the speaker will result. , 4

A 4 degree upward tilt can also be achieved by attaching the top knob to the

closest hole from the rear of the bracket and by attaching the bottom knob to

the furthest hole in the bracket See Figure 8).

Lowell Manufacturing recommends that a safety cable be used when

speakers are installed over-head The OS-150T has four (4 -20 tapped . ) ¼”

insert points on the rear of the speaker. When mounting the speaker using

the U-bracket that is included, one or more of those ¼”-20 tapped insert

points can be used to attach a safety cable .

TOP/TILT-DOWN

BOTTOM/TILT-DOWN

TILT-DOWN

FIGURE 3

FIGURE 4

FIGURE 5

FIGURE 6 FIGURE 7 FIGURE 8

TOP/TILT-UP

BOTTOM/TILT-UP

TILT-UP

Instruction Sheet

IS-OS150

Issued 1- -: 13 16

Lowell Manufacturing Company 100 Integram Drive Pacific, Missouri 63069 U.S.A.

Call: 800-325-9660 Fax: 636-257-6606 Click: www.lowellmfg.com

Due to its 70o square linear dispersion pattern (same vertical dispersion as the

horizontal dispersion) the OS-150T is ideal for use in open architecture ,

ceilings firing straight down in a distributed speaker system (See Figure ). 11

The maximum recommended center-to-center spacing is given in the table

below for edge- -edge spacing at a 4 average listening level. Note that to '

center-to-center spacing that is closer than the maximum given in the table,

will result in desirable overlapping coverage. Spacing that is farther apart than

the maximum given in the table will result in undesirable dead spots between ,

the speakers where the coverage is not optimized for listening. The paper at

the link below explains the “linear dispersion” concept for distributed systems.

http://www.lowellmfg.com/tinymce/jscripts/tiny_mce/plugins/filemanager/files/LowellDSSS.pdf

A sound system should be able to achieve a minimum sound pressure level at

every listeners position of at least dB above the loudest expected ambient 10

noise level. To assist the designer with those calculations the on-axis ,

maximum sound pressure level for the OS-150T is given in the table below for

the selector switch in the 8-ohm position (150 watt input and for each of the )

possible transformer tap input selector switch positions.

Distance

Power 2 Feet Feet Feet Feet Feet Feet Feet Feet4 8 16 24 32 48 64 96 Ft. 128 Ft.

150 Watts

Input

60 Watts

30 Watts

15 Watts

7.5 Watts

3. Watts8

1.9 Watts

. Watts94

. Watts48

117dB

113dB

110dB

107dB

104dB

101dB

98dB

95dB

92dB dB 80dB 74dB 7086 .5dB dB 6468 .5dB 62dB 58.5dB 56dB

89dB 83dB 77dB 73.5dB dB 6771 .5dB 65dB 61.5dB 59dB

92dB 86dB 80dB 76.5dB dB 7074 .5dB 68dB 64.5dB 62dB

95dB 89dB 83dB 79.5dB dB 7377 .5dB 71dB 67.5dB 65dB

98dB 92dB 86dB 82.5dB dB 7680 .5dB 74dB 70.5dB 68dB

101dB 95dB 89dB 85.5dB dB 7983 .5dB 77dB 73.5dB 71dB

104dB 98dB 92dB 88.5dB dB 82 dB 80dB86 .5 76.5dB 74dB

107 89dB 101dB 95dB 91 dB.5 dB 85 dB 83dB.5 79.5dB 77dB

111 93dB 105dB 99dB 95 dB.5 dB 89 dB 87dB.5 83.5dB 81dB

Center- -Cen terto

Spacing

Center- -to

Center

Spacing

Spacing = Maximum center- -center spacing for to

edge to edge coverage at 4 listening level.'

Height Face of speaker from the finished floor= .

SpacingHeight Height HeightSpacing Spacing

8 Ft.

9 Ft.

10 Ft.

11 Ft.

12 Ft.

13 Ft.

14 Ft.

15 Ft.

16 Ft.

17 Ft.

18 Ft.

19 Ft.

20 Ft.

21 Ft.

22 Ft.

23 Ft.

24 Ft.

25 Ft.

26 Ft.

27 Ft.

28 Ft.

29 Ft.

30 Ft.

31 Ft.

5.6 Ft.

7 Ft.

8.4 Ft.

9.8 Ft.

11.2 Ft.

12.6 Ft.

14 Ft.

15.4 Ft.

16 8 . Ft.

18 2 . Ft.

19 6 . Ft.

21 Ft.

22 4 . Ft.

23 8 . Ft.

25 2 . Ft.

26 6 . Ft.

28 Ft.

29 4 . Ft.

30 8 . Ft.

32 2 . Ft.

33 6 . Ft.

35 Ft.

36 4 . Ft.

37 8 . Ft.

Speakers Aiming

St raight Down As

Seen From the Floo r

FIGURE 9

FIGURE 10

FIGURE 11

Note Safety cable is not shown.:

For some OS-150T installations the installer may choose to use an omni-style ,

bracket (by others to mount the OS-150T instead of using the U-bracket that )

is included. When an omni-style bracket is used remove the two bracket ,

knobs discard the U-bracket and then replace the bracket knobs in the , ,

tapped holes. The OS-150T has four (4 -20 tapped insert points on the ) ¼”

rear of the speaker that are spaced to accept an Omnimount 25.0W bracket

(see Figure 9 or Adaptive Technologies Group MM-016-BT bracket (see )

figure ). 10 When another manufacturer’s omni-style bracket is used to mount

the OS-150T overhead one of the U-bracket knob 5/ "-18 insert points , 16

should be used to attach a safety cable.

Product specificaties

Merk:	Lowell
Categorie:	Speaker
Model:	OS-150TB
Kleur van het product:	Zwart
Breedte:	228.1 mm
Diepte:	210 mm
Hoogte:	405.5 mm
Materiaal behuizing:	Kunststof
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	150 W
Diepte apparaat (met standaard):	293.5 mm
Hoogte apparaat (met standaard):	414.4 mm
Aanbevolen gebruik:	Universeel
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Muur-montage
Diameter driver:	203.2 mm
Frequentiebereik:	65 - 20000 Hz
Gevoeligheid:	91 dB
Luidspreker soort:	2-weg
Roostermateriaal van luidspreker:	Aluminium