Lorex ETP-01T Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor Lorex ETP-01T (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Package
ETP-01T (Transmitter)
ETP-01R (Receiver)
Quick Start
Guide
Hardware Overview
Overview
ETP-01 Series are High-Speed, long distance Ethernet & PoE extender
that makes possible to transmit the Ethernet signal and PoE up to
300m through single pair of twisted wires.
It is cost-effective and time saving solution to migrate existing
analog system to IP based system since ETP-01 series support easy
installation utilizing the existing UTP bundle cables or any single
twisted pair cables.
With long distance transmission feature, the device makes to
overcome 100 meters distance limitation easily and reduces the
construction cost significantly compared with fiber optic configuration.
Features
Long reach Ethernet & PoE extension over existing 2-Wire twisted
cable
Data + Power over twisted cable
Data and PoE distance up to 300 m
100Mpbs Full Duplex
PoE, PoE+, Extra PoE (Max. 60W PoE output, ETP-01T model only
with DC Power adapter)
LED Indication (Data, Power)
Plug & Play
Surge Protection
Support PoE, PoE+ Input (25.5W) from PoE Switch / PoE NVR
(ETP-01R model only)
Slim design
Quick Start Guide
ETP-01T / ETP-01R
Please read carefully the instruction manual before use.
Contents of this manual are subject to change without prior
notice for reasons such as functionality enhancements.
Installation Guide
1. Connect Ethernet cable (Cat5e or better) from PoE Switch/NVR to
ETP-01R. Check LEDs on ETP-01R.
Ethernet cable
(Cat5e or better)
PoE Switch/NVR
Check LEDs
2. Connect single twisted pair cable to ETP-01R.
Connect single twisted pair cable from ETP-01R to ETP-01T.
2-Wire Twisted cable
3. Connect Ethernet cable (Cat5e or better) from ETP-01T to IP
Camera. Check LEDs on ETP-01T.
Î
Set ETP-01T, PoE Switch ON to supply direct power to IP camera.
Set ETP-01T, PoE Switch OFF to connect PC or network switch
devices.
Check LEDs
Ethernet cable
(Cat5e or better)
LED Indicators
Indicator Color Function
LINK Ethernet Data Act
ACT Ethernet Connect Act
Attention polarity( , ).
Rev.4.0
Ri tgh
Left
Top
RJ45
Status LED Indicator
LINK
Status LED Indicator
ACT
DC Power JackTeminal connector
PoE Switch ON/OF
(ETP-01T only)
Mounting
Screw Hole
Mounting
Screw Hole
Caution
Please install the device following the installation guide.
Do not touch the device and cable with wet hands.
Keep away from moisture and shock.
Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus that produce heat.
Indoor use only. (Use waterproof junction box when it is used in
outdoor)
Do not use for other purposes.
Do not disassemble or modify this device.
Do not put any sticker or paint on it.
If this device is defective or malfunctioning, please unplug the power
source immediately and contact dealer or service center.
Please use the rated power supply for the product.
Connect DC power to this device first and then to AC outlet when
using DC power supply.
Warranty
This device has passed the quality control and product inspection.
Please install and use according to the installation guide.
The warranty period for this product is 24 months from the date of
purchase.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Any damages or breakage from user’s abuse, accident, modification
or natural disasters will not be covered manufacturer’s warranty.
Please visit below website for more detailed information.
Web: http://www.intercoax.com Tel: +82. 31. 365. 3133~4
E-mail: info@intercoax.com Fax: +82. 31. 365. 3135
This device complies with part 15 of the fcc rules. Operation is subject to the
following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference
that may cause undesired operation
Specification
Model ETP-01T ETP-01R
Interface
2-Wire 1 x 2-Pin Terminal Block–
Ethernet over 2-Wire cable
Ethernet 1 x RJ45 - 100 Base-T
Transmission Rate 100Mbps Full Duplex
(100Mbps between Intercoax devices)
Transmission
Distance
Ethernet Up to 300m (1 Pair of Cat.5e)
PoE (PoC) Up to 300m (1 Pair of Cat.5e / 7W Camera)
LED
Indication Ethernet 1 x Link (Yellow) / 1 x ACT (Green)
Power
Input T-Linx or DC48V~57V PoE Switch or
DC48V~57V
PoE Output
IEEE802.3af (PoE),
IEEE802.3at (PoE+),
Extra PoE up to 60W
with 57V Power
Adaptor
PoE Not
Supported
PoC Only
Mechanical
Dimension 93(L) x 51(W) x 24(H)mm
Weight 52 g
Environment
Operating
Temp -20 ~ 60Β°C
Storage
Temp -30 ~ 80Β°C
Relative
Humidity 10% ~ 90%
Compliance
Certification FCC, CE, KC, RoHS
Surge
Protection
IEC 61000-4-5 4kV(1.2 / 50us),
2kA(8 / 20us)
Optional Accessories 57VDC / 1.2A External Power Supply
Applications
[Simply IP and PoE over 2-Wire]
2-Wire CableTwsited
E RTP-01
E TTP-01
PoE NVR
PoE
C raame
[High Power over 2-Wire]
NVR
2-Wire CableTwsited
57V DC/1.2A Power Supply
(Sold Separately)
PoE
C raame E TTP-01
E RTP-01
[Extra PoE (60W) over 2-Wire]
57V DC/1.2A Power Supply
(Sold Separately)
2-Wire CableTwsited
PoE NVR
PoE
C raame E TTP-01
E RTP-01
Β© Intercoax Co., Ltd.


Product specificaties

Merk: Lorex
Categorie: Niet gecategoriseerd
Model: ETP-01T

Heb je hulp nodig?

Als je hulp nodig hebt met Lorex ETP-01T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Lorex

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd